Turner Hastings HTRCPT Operation manual

7 Day Programmable Timer
Installation & User Guide
TRTS / TRTSB / TRTSL

2
Installing the timer
User Interface
Setting the date & time
Heating modes
Advanced settings
Setup your heating schedule
Factory Reset
Temporary override
Holiday Mode
Key lock
Technical data
Service and support
3
5
6
7
8
9
16
17
18
19
19
20
Contents
............................
................................
.......................
................................
............................
...................
..................................
.............................
..................................
.......................................
.................................
............................

Carefully remove the back of the timer by placing a
flat head screwdriver into the slots on the bottom of
the unit and push to release.
Unplug the cable connector from the back of the
timer screen.
Connect the Turner Hastings towel rail to the timer as
seen in the below wiring diagram.
Installing the timer
3

Screw the back plate of the timer to the
electrical plate.
Plug the cable connector into the back of the
timer screen and connect the screen to the back
of the timer.
Installing the timer
4

User Interface: Portrait
1. Day indicator
2. Key lock icon
3. Schedule mode icon
4. Manual mode icon
5. ON/OFF indicator
6. Confirm settings
7. Program button
8. Mode button
9. Power button
10. Up & down arrows
11. Time
5

1. Day indicator
2. Key lock icon
3. Schedule mode icon
4. Manual mode icon
5. ON/OFF indicator
6. Confirm settings
User Interface: Landscape
6
7. Program button
8. Mode button
9. Power button
10. Up & down arrows
11. Time

Press and the time will begin to flash
Use to select the correct time
Press until the day begins to flash
(Note: Monday is Day 1)
Use to select the correct day
Press to save the settings
7
Setting the date and time

When the timer is on, press the to switch
between manual and schedule modes.
Manual Mode
In manual mode press the to set the
ON/OFF status.
Schedule Mode
In the schedule mode the timer will follow the
heating schedule that is set.
Refer to page 9 for programming instructions.
8
Heating Modes

To access the advanced settings, turn the timer
off by pressing
Press to display setting 01
Use the to adjust the settings
Press to cycle between setting 01 to 03
Press to save the settings
Menu Description Range Default
01 Clock Format 24
02 5+2 or 7 Day
Programming 01=5+2 Day Program
03 Screen Saver
12 or 24
01=5+2 Day Program
02=7 Day Program ON
= Activated
OF = Not Activated OF=Not Activated
9
Advanced Settings

Turn the timer on by pressing
To set up the heating schedule for Monday to
Friday press
The time for P1 will flash. This is the first ON
period for the day.
Use the to adjust the time to when the
heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
10
(For 5+2 Day Program)
Set up your heating schedule

Press and the ON / OF will flash.
Using the select OF for P2.
Repeat above steps for P3 and P4 and then press
(Note: P3 is turning the heated towel rail on in the
evening and P4 is turning it off in the evening)
If the heated towel rail is only required to be on
once a day set to OF for both P3 and P4 and
ensure that the time set for P3 and P4 is after the
time set for P2.
When Monday-Friday has been set press
to go onto the Saturday and Sunday schedule.
11
Set up your heating schedule (For 5+2 Day Program)

The time for P1 will flash. This is the first ON
period for Saturday and Sunday.
Use the to adjust the time to when the
heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2.
Repeat above steps for P3 and P4
12
Set up your heating schedule (For 5+2 Day Program)

Turn the timer on by pressing
Change the menu option 02 to setting 02
(7 Day Program) as per instructions on page 8. The
7 day program option means that all 7 days are
programmed to the same schedule or all 7 days are
programmed individually.
Press until the day display flashes.
If programming all 7 days individually use the
to select the day to program first.
If programming all 7 days to the same schedule,
press and hold the button for about 5 seconds
to select all 7 days.
13
Set up your heating schedule (For 7 Day Program)

To set up the heating schedule press
The time for P1 will flash. This is the first ON
period for the day.
Use the to adjust the time the heated
towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2
Set up your heating schedule (For 7 Day Program)
14
Set up your heating schedule (For 7 Day Program)

Repeat above steps for P3 and P4 and then press
(Note: P3 is turning the heated towel rail on in the
evening and P4 is turning it off in the evening)
If programming all 7 days to the same schedule, the
program is now set up.
If programming all 7 days individually, press and
use the to select the next day to program.
Set up your heating schedule (For 7 Day Program)
15
Set up your heating schedule (For 7 Day Program)

Press to turn the timer off
Press and the hold until 04 is displayed
Press and hold for approx. 5 seconds
will display on the screen and then the
timer has been reset.
Turn the timer back on to setup the program
Factory Reset
16
Factory Reset

and the
In schedule mode, press the
ON/OFF display will flash.
Use
press
to adjust the desired setting and
to confirm.
will be displayed below the
ON/OFF display. To cancel the override setting
press .
Temporary override
Turning the timer onto temporary override will
allow the timer to be operated on manual until
the next programmed period.
17
Temporary Override

The Control Panel timer does not have a dedicated
holiday mode. To suspend the heating schedule for
a period of time turn the timer off using the button.
This will ensure the heating schedule is held and
then to resume the heating schedule press the
button.
18
Holiday Mode

To lock the key pad, press and hold the for 5
displays. To unlock
seconds or until the
press and hold the until the disappears.
Supply voltage
Maximum Load
IP Rating
Warranty
Width
Height
Depth
230 - 240VAC
16A
IP30
2 Years
80mm
120mm
45mm (27mm in wall)
Technical data
19
Key Lock

Turner Hastings
16 McPherson Rd, Smeaton
Grange NSW 2567, Australia
1300 00 2284
www.turnerhastings.com.au
Service and support
20
Service and Support