Turnstiles PY300DC User manual

PY300DC
Sliding Gate Opener
User Manual

1
Dear users,
Thank you for choosing this product. Please read this manual carefully before installation and use.
Please do not forget to include this manual if you send the product to a third party.
1. Safety Instruction
Please make sure that the power voltage being used matches with the supply voltage of gate
opener (AC110V or AC220V); kids are not allowed to touch the control devices or the
remote-control unit.
The remote-control unit is single button mode or three button mode (please refer to the instructions
of the remote control in accordance with the actual gate opener type). The indicator light on the
remote-control unit will flicker when its button is pressed. Main engine and gate can be unlocked
with a disengagement wrench and the gate can be manually operated after disengagement.
Please make sure that nobody is around the main engine or gate when the switch is operated.
Please temporarily stop using the product if the main engine needs to be repaired or regulated. The
installation and maintenance of the product must be carried out by professionals.
Please read this manual carefully before installing、using、maintaining or repairing it. Without
following this manual, any injury or property losses caused by improper use or unauthorized
modification is out of the responsibility of our company.

2
2. Packing List (standard)
No.
Picture
Name
Quantity
1
Main engine
1
2
Manual release key
1
3
A
B
C
D
A
B
C
D
Remote control
2
4
Accessories box
1
4-1
Manual release bar
1
4-2
Foundation bolt M8
4
4-3
Nut M8
8
4-4
Flat washer Ø8
4-6
4-5
Spring washer Ø8
4-7

3
2. Packing List (optional)
No.
Picture
Name
Quantity
1
Steel gear rack
1m/pc
2
Nylon gear rack
1m/pc
3
Infrared sensor
1
4
0
8
5 6
97
4
1 2 3
Wireless keypad
1
5
Alarm lamp
1
6
Mounting plate
1
3. Technical parameters
Model
PY300DC
Power supply
220V/50Hz;110V/60Hz
Motor power
100W
Gate Moving speed
13m/min
Maximum weight of gate
300Kg
Remote control distance
≥30m
Remote control mode
Single button mode
Limit switch
Electronic limit switch
Noise
≤60dB
Working duty
S2, 20min
Recording of up remote controls
20
Frequency
433.92 MHz
Working temperature
-20°C ~ +70°C

4
Storage battery
24V 4.5Ah
Package weight
11.32Kg
4. Installation
PY300DC sliding gate opener is applicable to gate weight less than 300kg, and length of the sliding
gate less than 8m. The drive mode adopts the rack and gear transmission. This gate opener must
be installed inside the enclosure or yard for protection.
4.1 Installation drawing
⑤
④
③
②
0
8
5 6
97
4
1 2 3
⑧
①
⑦
⑥
Figure 1
①Gate opener; ②Wireless keypad (optional); ③Gate; ④Infrared sensor (optional);
⑤Alarm lamp (optional); ⑥Safety stop block; ⑦Gear rack; ⑧Remote control;
4.2 Size of main engine and accessories
4.2.1 Size of main engine

5
300
270 200
Figure 2
4.2.2 Size of mounting plate
200±0.2
270
150
100±0.2
4×φ10
Figure 3
4.3 Installation procedures
4.3.1 Preparation work before installation
Please make sure that the sliding gate is correctly installed, the gate rail is horizontal, and the gate
can be manually moved smoothly before installing the gate opener.
Cable installation
In order to guarantee the normal operation of the gate opener and protect the cables from damages,
please bury the motor & power cable and controlling cable separately with two PVC tubes.
Concrete pedestal
Please precast a concrete pedestal with the size can be 400mm x 250mm, depth be 200mm in
advance, so as to firmly install PY300DC gate opener. Please make sure the distance
between the gate and gate opener is appropriate before casting the pedestal.

6
Embedded screws
Concrete
Power line
Mounting plate
Foundation bolt
Figure 4
4.3.2 Main engine installation
a) Dismantle the plastic housing on the main engine before installation and keep relevant fasteners
properly;
b) Please prepare the power line for connecting the mounting plate to the main engine (the number
of power supply cable cores should not be less than 3 PCS, the sectional area of cable core should
be over 1.5mm²and the length should be determined by users according to the situation on
installation spot)
c) Please unlock the main engine before installation, the unlock method is: first remove the upper
cover, and then insert the key to open the shell cover. Insert the manual release bar into the release
hole and clockwise rotation till the output gear can be rotated easily, which means the motor has
been released.
Figure 5
4.3.3 Gear rack installation
Fix the mounting screws to the rack.
Put the rack on the output gear, make the rack engage with the output gear then weld the
mounting screw to the gate (each screw with one solder joints firstly).
Manually move the gate (gate should be moved smoothly after motor unlocked) to check

7
whether there is a fit clearance between rack and output gear, as shown in Figure 7.
Weld all the mounting screws to the gate firmly.
Make sure that all racks on the same straight line.
Pull the gate after installed, make sure the entire trip is flexible without any stuck.
Figure 6
The fit clearance of output gear and rack is shown in Figure 7 below:
1-21-2
GearGear rackrack
OutputOutput geargear
mmmm
Figure 7
Warnings
·To ensure safety, install safety stop blocks on both ends of the rails to prevent the gate from running
out of the rail. Before installing the main engine, make sure that the safety stop blocks are in place
and whether it has the function of preventing the gate from running out of the rail or safety range.
·Please make sure that the main engine and its components have good mechanical properties, and
the gate can be operated flexibly when manually moved before installing the main engine.
·Please note that for this product, one control can only drive one main engine, otherwise, the control
system will be damaged.
·Earth leakage circuit breaker must be installed in where the gate movement can be seen, and the
minimum mounting height is 1.5m to avoid being touched by children.
·After installation, please check whether the mechanical property is good or not, whether gate
movement after manual unlocking is flexible or not, whether the installation for infrared sensor
(optional) is correct and effective.

8
4.3.4 Control board wiring
－LAMPLAMP＋
GNDGND
PEPE
+24V+24VCLOSECLOSE STOPSTOP OPENOPEN C OMCOM OSCOSC
COMCOM
InfraredInfrared sensorsensor
24VDC24VDC
AlarmAlarm lamplamp
StopStop buttonbutton
CloseClose buttonbutton
OpenOpen buttonbutton
SingleSingle buttonbutton switchswitch
＋SOLARSOLAR BATBAT－＋ RECHGRECHG BATBAT－JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
C1C1
J5J5
J3J3
J2J2
C5C5
C20C 20 C18C 18
VCCVCC DATADA TA GNDGND GNDGND ANTANT
24VAC24VAC M
24VDC24VDC motormotor HallHall lineline
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
COMCOM
Figure 8
Transformer wiring:
＋SOLARSOLAR B ATBAT －＋ RECH GR ECHG B ATBA T－JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
ControlControl boardboard
TransformerTransformer inputinput 220VAC220VAC
TransformerTransformer outputoutput 24VAC24VAC
Figure 9

9
Control board wiring instruction:
24VDC motor: black wire to “T1”, red wire to “T2”. If the gate opening direction is wrong, please
exchange T1 and T2.
J1: Transformer secondary (AC24V / 3.3A);
J2: Singe button (OSC and COM);
Three button (OPEN, CLOSE, STOP, COM);
J3: Infrared sensor (PE and COM);
Output DC power (24V and GND);
J4: Alarm lamp, voltage 24VDC;
J5: Solar panel and storage battery;
J6: Hall line.
Set open and close positions:
1. Press and hold SET until number “1” is indicated on the LED display.
2. Press and hold OPEN to reach the desired open position (press OPEN button, the door must in
open direction, otherwise exchange the two motor wires).
3. Press the SET to confirm the open position, LED display indicates “2”.
4. Press and hold CLOSE to reach the desired close position.
5. Press the SET to confirm the close position.
6. The door will do a complete open and close cycle.
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 10
Set automatic close time:
1. Press and hold OPEN until “─” is indicated on the LED display.
2. Press OPEN to increase the automatic close time, press CLOSE to decrease the time.
3. Set time to “0”, the automatic close function will disable.
4. Press SET to confirm the setting.
5. Add 10 seconds per number.
NOTE: Automatic close function is available only when the door is in fully opened position.

10
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 11
Set obstruction force:
If the door meets an obstruction during closing, it will stop and reverse about 15cm~20cm.
1. Press and hold SET. The LED will display number from “1” to “4”, when the number “3” appears
on the LED display, release the SET.
2. Press OPEN to increase the obstruction force, the maximum force is level 9. Press CLOSE to
decrease force, the minimum force is level 1.
3. Press SET to confirm.
NOTE: Please adjust the obstruction force according to door weight, so that the obstruction
force can be in a state of security protection, otherwise it may cause security risks.
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 12
Set infrared protection function:
1. Press and hold CLOSE until “─” is indicated on the LED display
2. Press OPEN, LED display indicates “H”, the infrared protection function is enabled.
3. Press CLOSE, LED display indicates “||”, the infrared protection function is disabled.
4. Press SET to confirm. (When not use photocell, please set to “||” status).
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 13

11
Infrared photocell function: In the closing process, when infrared ray of the photocell is covered by
people or objects during its detection range, the gate will open immediately for security protection.
The distance between photocell receiver and photocell emitter should be more than 2 meters,
otherwise will affect the induction of the photocell.
Wiring as below, the photocell output signal must be N.C..
－LAMPLAMP＋
GNDGND
PEPE
+24V+24VCLOSECLOSE STOPSTOP OPENOPEN COMCOM OSCOSC
J1J1
C1C1
J5J5
J3J3
J2J2
V+V-
V+V- NO COM NC
InfraredInfrared receiverreceiver connectingconnecting InfraredInfrared emitteremitter connectingconnecting
Figure 14
Add extra remote control:
1. Press CODE, the red dot on the LED display will be on.
2. Press one of the transmitter’s buttons which you want to use, and then press the same button
again after one second.
3. The dot on the LED display will flash then turn off.
4. “||” is indicated on the LED display, which means the learning process is finished. A maximum of
20 remote controls can be learned.

12
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
A
B
C
D
1 2
3 4
Figure 15
Delete remote control:
Press and hold CODE until “C” is indicated on the LED display. This indicates that all remote
controls that learned previously have been deleted.
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 16
Remote control:
RemoteRemote controlcontrol
A
B
C
D
CLOSECLOSE
OPENOPEN
STOPSTOP
Figure 17

13
Storage battery wiring:
＋SOLARSO LAR BATBAT－＋ RECHGRECHG BATBAT－JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
StorageStorage batterybattery
ControlControl boardboard
Figure 18
Solar panel wiring:
＋SOLARS OLAR B ATBAT－＋ R ECHGRECHG BATB AT－JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
CHARGECHARGE LOADLOAD BATTERYBATTERY
＋ － ＋ － ＋ －
＋
－
＋
－
SolarSolar panelpanel SolarSolar chargercharger
StorageStorage batterybattery
ControlControl boardboard
Figure 19

14
5. Others
5.1 Maintenance
Check whether the gate operates normally every month.
For the sake of safety, each gate is suggested to be equipped with infrared protector, and regular
inspection is required.
Before installation and operation of the gate opener, please read all instructions carefully.
Our company reserves the right to change the instruction without prior notice.
5.2 Troubleshooting
Problems
Possible Reasons
Solutions
The gate cannot open or
close normally, and LED
does not light.
1.The power is off.
2.Fuse is burned.
3.Control board power wiring with
problem.
1.Switch on the power supply.
2.Check the transformer input
interface fuse, change the fuse
if burnt.
3.Re wiring according to
instructions.
The gate can open but
cannot close.
1.Infrared protection function is
disabled, but not connect
photocell.
2.Photocell wiring with problem.
3.Photocell mounting with problem.
4.Photocell is blocked by objects.
5.Sensitivity of obstacle is too high.
1.Connect photocell or disable
infrared protection function.
2.If not connect photocell,
please make sure that the
infrared port and GND short
circuit; if connect infrared
sensor, please make sure the
wiring is correct and the
photocell is N.C.
3.Make sure that the photocell
mounting position can be
mutually aligned.
4.Remove the obstacle.
5.Reduce the sensitivity of
obstacle.
Remote control doesn’t
work.
1.Battery level of the remote
control is low
2.Remote control learning is not
completed
1.Change the remote control
battery
2.Re-conduct remote control
learning
Press OPEN, CLOSE
button, the gate is not
moving, motor has
noise.
Gate moving is not smoothly.
According to the actual
situation to adjust the motor or
the gate.

15
Leakage switch tripped.
Power supply line short circuit.
Check wiring.
Remote control working
distance is too short.
Signal is blocked.
Connect external receiver
antenna, 1.5 meters above
ground.
The gate moves to the
middle position to stop
or reverse.
1.Obstruction force is too small.
2.Gate meets obstacle.
1.According to the instruction
to increase the obstruction
force.
2..Remove the obstacle.
Gate opens
automatically
Automatic close function has been
turned on but with incorrect
opening direction.
Please refer to the attentions
under 4.3.4 to change the
opening direction.
Warranty
Warranty Ordinance
1. To repair against this warranty card and invoice during the warranty period.
2. Warranty period: 1 year after the date of invoice.
3. Without unauthorized dismantling, any product broken or damage due to quality problem, we’ll
offer the repair service for free or replace for free.
4. The malfunction and damaged caused by incorrect use or man fault is not covered by this
warranty.
Maintenance Record
Check Date
Check Content
Maintained by
2018V1