Tview T712HR-IR User manual

OWNER'S MANUAL
7" 16:9 TFT LCD MONITOR
T712HR-IR
T712HR-IR
T71 2HR -IR
POW

Appearance and function
Thank you for your purchasing LCD monitor. Please read this manual
carefully before operating and reserve it for future reference. It will be
helpful to you if you encounter any operational problem.
01 02
MODEL:T712HR-IR
1 2
34
56
1). –: MENU adjustment reduce.
2). +: MENU adjustment increase.
3).POW: Power on or off.
4).MENU: Menu adjustment.
5).V1/V2: Display mode switch.
6).Remote control window.
7).IR transmit window
Noted: This product is for touch
influence type button. More
convenient for operation. Just
touch the button, the button
indicator light will flicker; The
unit can adjust to the picture
which you need for .
Specification
Name: 7” TFT LCD Monitor
Resolution: 480x3(RGB)x234
System: PAL/NTSC
Power: DC12V 1A ±10%
Power consumption: 6W
Signal: AV1/AV2+IR
Screen size: 7"(16:9)
Remote control: full function remote control operation.
7
T71 2HR- IR
POW
+12V DC
Ground
Fuse box
A
RC Yellow AV1
RCA Yellow Av2
CAUTION:
please observe the right polarity of the cables an the right colours of the RCA-plugs
A
RC Wht I
i e LN
A e
RC R d R IN
Connections
·Before using the device, please check it for any possible damages. In case of
damage do not operate it.
·Unplug the device if you do not use it for a certain time.
·The device may not become subject of mechanical stress and should not be
exposed to humidity.
·To be considerate of the ventilation do not cover the device and protect it from
direct solar radiation.
·Clean the device with a dry and soft cloth only.
·Caution! Should the device itself get damaged, please let the repair to the
manufacturer or to a qualified service agent.
·Please dispose packaging materials properly and do not let play children with it.
·The device itself is no toy either. Do not let children play with it too
Security Advices

03 04
1.Power: Turn on/off po wer
2. : Pres s them to increase and decr ea se the bri ghtness.
3. COL: Pres s the m to inc rease and decrease the color.
4. : Pres s them to increase and decr ea se co nt rast.
5. : Pres s it to select the mode
(standard, light, so ft, vi vi d, mem ory)
6.Reverse: Turn the pi cture from lef t to righ t or up to do wn.
7.V1/V2: AV1/AV2 to sw itch
POWER
COL
1
2
3
4
SYS
V1\V2
5
6
7
Remote Control
The above functions can be executed by MENU on the display
or remote control unit.
Press the MENU of unit , you can choose “BRIGHT”
“COLOR” “CONT” “TINT(ONLY NTSC SYSTEM)”
“LANGUAGE” “SCALING”, then press “+” “-” on the unit to
adjust that you need. Or press / col / “ ” “ ” on the
remote control directly adjust “BRIGHT” “COLOR”
“CONT”
.
.
.
.
Precautions before using remote control unit
AV Display Mode:
Remote control unit operating range
6
1.
Replacing the battery
2.
3.
Operating method: Press the button “V1/V2” on the remote
control or the unit to choose AV display mode. If the VCD or DVD
signal is connected, there should be display normally pictures
signal; If the VCD or DVD signal isn't connected, the screen is
blue. the system will display “NO SIGNAL”.
1. BRIGHT
2. COLOR
3. CONT
4. TINT(only NTSC system)
5. LANGUAGE
6. SCALING(16:9/4:3)
IR: The machine equipped with IR audio transmitter, frequency
(2.3MHZ, 2.8MHZ), please choose a suitable infrared
receiver headset answering, receiving distance in a straight
line within 3 meters
IR emission from AV1/AV2 audio control, as long as the boot,
with the audio input can be launched

05
ALARM
For your safety, driver are advised not to watch the display when driving.
It's prohibited in law of some countries when driving and operating to
watch displayer.
Simple Trouble-Shooting Guide
Symptom Probable Cause Solution
Black Screen
1.No12 voltage
2.Brightness or contrast
ratio is too small
3.no high-voltage
1 .check the power is on or
connect rightly
2. check the A/V Cable
is loose or not
3. Increase the brightness
and contrast ratio
NO picture
1.No sources output
2.The video concentric plug
becomes loose
1.Check the output of VCD
or DVD
2.Replace with the A/Vcable
3.Tighten the Video input
cable
color picture
1 Video sources have
no output
2.Color ratio should be
re-adjust
1.check the video sources
2.Enter into the Menu to
re-adjust
With a little regular light
spots and color spots on
the screen or black
horizontal line in the
picture
It is normal symptom in the
active matrix display
technology.
it is normal symptom in
view range with a little
regular light spots on
display screen.
Unclear picture
1.Poor quality of the
video sources
2.Bright &Contrast
1.Replace with the high
quality videodisc
2.Reset Bright &contrast.
The outer cover of the
monitor has been deformed
1.External temperature is
too high.
2.The power has not been
switched off for a long time.
1.The surround temperature
should not exceed to 0-60
degrees.
2.Turn off the power after
using the unit.
If your product fails, please follow the way of exclusion, if it is still
unresolved, please contact the professional or supplier.