TVT TD-6424M3 User manual

Package
Overview
Installation
1
2
3
4
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the Ethernet connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ The grounding hole of the product is recommended to be
grounded to further enhance the reliability of the camera.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Panoramic Bullet
Network Camera
Camera Quick start guide
CD Plastic plug ×4
Drill template
Screwdriver Rubber plug
4 tapping screws
● Connecting Alarm Input/Output
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
2
13
1 Ethernet Connector *
2 Audio Input (MIC)
3 Audio Output (HP)
4 Alarm Input/Output
5 RS485
6 Power Connector *
7 Ground
8 Reset
9 Micro SD Card Slot
* 1
* 2 This camera can be powered by DC 12V/PoE power supply. If the PoE switch
is used to power the camera, DC12V power supply is not required.
It is recommended to install the security cap for outdoor installation.
Security cap
Ground
1
3
4
5
6
7
89
2
ALARM
4 3 2 1
R 485
S
+
ALARM
4 3 2 1
R 485
S
+
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
RS485T+
RS485T-
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
① Open the cover of the camera and then insert a micro SD card.
Then install back this cover and fix it firmly with the screws (please
keep it flat when installing).
● Connecting Network Cable
Alarm
Power Source
IPC
ALARM-COM
ALARM-OPEN
Alarm Input
Alarm Output
+
+
--
Sensor
IPC
ALARM-INA
ALARM-GND
3
4
1
2

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
● Access Through IP-Tool
● Camera Mounting with a Junction Box
Here we take accessing IP camera via LAN for example.
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the ad ministrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address to open up the web browser or
manually enter the modified IP address in the address bar of your
browser. Then follow directions to download and install the plugin if
it is the first time for you to log in.
the user name and password in the login interface.
The default username is admin; the default password is 123456.
⑤ Enter
450043001316 A0
② Drill the screw holes and the cable hole (if you want to route
through the ceiling) on the wall or ceiling according to the drill
template.
Insert a micro
SD card
Mounting base
Rubber plug
Fixed screws
∅4.50mm
90.23mm
90.22mm
③
the mounting base to the wall with the screws provided.
Route the cables and connect the relevant cables. Then fasten
④ Bracket adjustment. Before adjustment, preview the image of the
camera on a monitor and then loosen the fixed screws to adjust the
view angle of the camera. After that, tighten the fixed screws.
Rotate: 360
Pan: 360
Tilt: 90
°
°
°
① Mount the junction box to the wall or ceiling with screws.
② Route the cables and connect the relevant cables (Take cable
going through mounting surface for example).
③ Fix the camera onto the junction box with screws.
Cover
Daily Maintenance
Lens cover is an optical element. Please don’t touch or wipe the cover surface directly
during installation and use. Please follow these cleaning tips to clean it.
* If there is dust on the lens cover, please use a dry soft brush to gently brush it .
* If there is water or grease on the lens cover, please gently wipe off the water or grease
with a soft cloth. Then use oil-free cotton cloth with a little neutral detergent to wipe it
several times until it is clean. Finally, change the cloth to dry it .
* If there are fingerprints on the lens cover, please use oil-free cotton cloth or paper
soaked with a little neutral detergent to wipe it several times and then dry it with a soft
cloth.
Tips