TVT TD-9555A3-PA User manual

Package
Overview
1
2
3
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Network Camera
Camera Quick start guide
CD Plastic plug × 4 Rubber plugDrill template
Screwdriver
Tapping screw ×4
■ Please read this instruction carefully before operating the
unit and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
Security Cap
1
2
3
4
5
6
7
8
9
Ethernet connector
Audio input connector
Audio output connector
Alarm input/output
Power connector
Speaker
Microphone
Micro SD card slot
Reset
89
ALARM
4 3 2 1
1
2
3
4
5
6
7
1--ALARM-COM
2--ALARM_OPEN
3--ALARM_INA
4--ALARM_GND
DC12V
ALARM
4 3 2 1
Sensor
IPC
ALARM-INA
ALARM-GND
Alarm
Power
IPC
ALARM-COM
ALARM-OPEN
+
+
-
-
3
4
1
2
► Connecting Alarm Input/Output
Alarm Input
Alarm Output
Installation
4
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
2
13
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment.
① Loosen the fixed screw to disassemble the camera.
Fixed Screw Mounting Base
Enclosure
Dome
MIC
HP

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
● Access Through IP-Tool
① Make sure that the camera and the PC are connected to the local
network.
② Install IP-Tool from the CD and run it after installation.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Devic e Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as the
computer’s. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 201
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the camera listed in the IP-Tool or manually enter
the IP address in the address bar of the web browser to connect IP
camera. Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
450043001344A0
The default username is admin; the default password is 123456.
② Unscrew the cover of the dome and then insert a micro SD card.
After that, install back the cover. (Note that the cover shouldn’t be
installed unevenly.)
Insert a micro SD card
Cover
③ Drill the screw holes and the cable hole on the ceiling according
to the drill template.
Ø107.7
Ø5.0
Ø79.4
56.1
56.1
(mm)
④
ceiling or wall with the screws provided.
Route and connect the cables. Then secure the mounting base to the
⑤ Install the dome and enclosure to the mounting base and then
adjust the dome to obtain an optimum view angle. Finally, fix the
camera with the fixed screw.
Fixed Screw