TVT TD-6528M3 User manual

Quick Start Guide
Outdoor 360° Panoramic
Network Camera
Outdoor 360° Panoramic
Network Camera

Thank you for purchasing this panoramic camera!
Please read this manual carefully before operating the unit and retain it for future reference.
All examples and pictures used in the guide are for reference only.
The contents of this manual are subject to change without notice.
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Do not use camera beyond specified voltage range.
Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of
electric shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper
enclosure cleaning (such as using cloth) may result in poor IR functionality and/or IR
reflection.
4. Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Important Safeguards and Warning
.

Overview
Cable Connection
1
2
1 Ethernet Connector(PoE)
2 MIC-Audio Input
3 HP-Audio Output
4 Alarm Input/Output
5 Power Jack
6 Ground
7 Reset
8 Micro SD slot
1
2
3
4
5
6
ALARM
4 3 2 1
78
RJ 45
HP
MIC
1-ALARM
2-ALARM-COM
3-ALARM-GND
4-ALARM-IN1
-OPEN
Power Jack
Ground
ALARM
4 3 2 1
Cover
1

► Connecting Alarm Input/Output
Max. load of the alarm output: 30VDC, 1A
2
► ower ConnectionP
When using 24V power supplyAC
ALARM_IN
ALARM_GND
ALARM_OPEN
ALARM_COM
ALARM
POWER
DC Support 3~12V DC IN
PE
Relay
Non-PoE Switch
ALARM
4 3 2 1
24V power supplyAC

When using a PoE switch
When using a PoE power injector
PoE+ Switch(Optional)
Connect the camera to an 802.3at PoE switch via a network cable.
ALARM
4 3 2 1
Network cable
Non-POE Switch
PoE+ Power Injector
(Optional)
ALARM
4 3 2 1
3
Installation
3
This camera supports outdoor pole mounting or indoor ceiling mounting.
Please select a way to install as needed. The following instructions are for
reference only.

Memory Card Installation
1. Unscrew the cover of the memory card.
2. Insert a micro SD card and then install the cover back with the screws.
Outdoor Mounting
4
Please make sure the installation surface is strong enough to bear the dome
camera’s weight and the camera is powered off during installation.
As dirt, dust, or fingerprints on the bubble will reduce the clarity of the
image, please keep it clean in the course of installing or using but DO NOT
directly touch or wipe it. DO NOT remove the protective film until the
installation is complete.
1m
It’s strongly recommended to mount the camera 1 m (4 feet) away from the
pole, to avoid image blur caused by the IR light beam reflection from the pole
into the camera lens.

2. Connect the relevant cables.
Make sure the side with the sign faces
people/vehicle flow when installing.
①②③
5
The recommended installation height ranges
from 4m to 8m.
1
pole according to the picture on the right.
. Install the bracket (not provided) to the
1 m
4~8 m

3. Attach the camera to the bracket with screws.
6
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Ground
Indoor Mounting
1. Install the ceiling mounting bracket (provided) according to the following
diagram.
It is recommended to install the camera in the center of the ceiling.

7
2. Mount the adapter tube to the bracket and fix it with a screw.
3. Secure the ceiling mounting bracket to the ceiling.
4. Connect cables and then hook the safety wire to the adapter stem.
5. Secure the camera to the adapter tube with screws firmly.
Adapter tube
4Network Connection
● Configuration Requirements:
* IE browser preview: CPU: i7 or higher; RAM: 4GB or higher;
Display: 4K@30fps resolution

8
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
Here we take accessing IP camera via IE browser in LAN for example.
● Access the camera through IP-Tool
① Make sure that the camera and the PC are connected via LAN.
② Install the IP-Tool in the computer. After that, run the IP-Tool
as shown below.
* NVR preview: support the NVR with 8K video decoding output
capability that can decode 16MP real-time video stream , or only the
sub or third stream can be decoded.
* Display Device: recommended aspect ratio: 32:9/32:10
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration

After the installation is complete, you can log in via IE browser and
adjust the horizontal scrolling range to make the obstacle display on
both sides of the image.
Go to Config>Image>Display Settings interface. Select the horizontal
scrolling range as needed.
③
camera. The default IP address of this camera is 192.168.226.201.
Then follow directions to download and install the plugin if
prompted.
Double-click the camera listed in the IP-Tool to connect the
④ Activate the device.
interface.
Enter the username and password in the login
The default username is admin;
The default password is 123456 or you can self-define the
password according to the actual situation.
9
Auto
Auto
0
50
Open
Open
Close
Close
Exposure Mode
Gain Mode
Gain Limit
Corridor Pattern
Horizontal 45
Scrolling
Image Mirror
Image Flip

Before adjustment
After adjustment
10