TVT TD-C12 User manual

Package
Overview
Installation
1
2
3
4
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -10˚C~45˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Network Camera
Camera
Drill template
Quick start guide CD
2 tapping screws 2 plastic plugs
■ Please read this instruction carefully before using the product and
keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
5
11
6
12
13
15
14
16
1
7
2
8
3
9
4
10
STATUS LINK AL ARM
ALARM
DC12V
RST
I
G
O
LAN
1
3
2
4
5
6
7
8
9
10
11
12
14
15
16
13
Lens
IR LED ( ON: visible)
Microphone
PIR (Passive Infrared) sensor
Power indicator
Network indicator
Alarm indicator
Light sensing
Ethernet connector & PoE
Speaker
Alarm I/G/O
Power connector
Reset or WPS
Micro SD card slot
3-axis bracket
Mounting base
● Alarm Connections:
I: Alarm input interface; O: Alarm output interface; G: Grounding
Alarm input: Connect the cables of the sensor to I and G interfaces.
Alarm output: Connect the cables of the alarm output device to O and G
interfaces.
230°
71°
360°
● Indicators
Power indicator: Green: the camera is started successfully.
Network indicator: Flashing blue: the camera is connected
to the wired network successfully.
Alarm indicator: Red: alarms are triggered.
● Reset
Press RST about 10s when the camera is powered on to
restore the default settings.
● 3-axis Bracket Adjustment
The camera can be placed on the desktop or installed on the wall.
Please make sure the wall is strong enough to withstand 3 times the
weight of the camera. The steps of wall mounting are as follows.
① Attach the drill template to the place where you want to fix the
camera. Then drill the screw holes on the wall according to the drill
template.
② Peel off the drill template and then insert the plastic plugs and
screws into the screw holes. Please leave a little clearance between
the wall and the screws.
● WPS
WPS (Wi-Fi Protected Setup): Press the WPS button on the router
and then press the RST button on the camera within 120s to quickly
connect the Wi-Fi. Pressing the RST button on the camera and then
pressing the WPS button on the router will work as well. The red
alarm indicator will flash if the Wi-Fi is connected.

Network Connection
5
MENU
Camera
Network Cable Network Cable
Switch
Router Computer
● Access the Camera Through the Wired Network
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as the
computer’s . Please modify the IP address of your device according
to the practical situation. After modification, please enter the
password of the administrator and click “Modify” button to modify
the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect the camera.
Then follow directions to download and install the applicable plug-in.
After that, enter the user name and password in the login interface.
● Access the Camera Through Wi-Fi
The default username is admin; the default password is 123456.
① Make sure that the camera and the PC are connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
② Run the IP-Tool and then find the IP address of the camera.
The default IP address of this camera is 192.168.226.201. Double
click it. This will bring you to the login interface of the camera.
Enter the default username and password to log in.
③ Click “Config”→ “Network”→ “WIFI” to go to the following
interface.
① Connect the camera to the LAN through the network cable.
450043001237 A0
③ Route and connect the cables.
④ Hook the mounting base to the screws and ensure that the
camera is fixed firmly. Then adjust the angle of the bracket.
⑤ Remove the protection films of the lens and the IR LED cover.
Lens
IR LED Cover
④ Enable WIFI and click “Search” to search wireless routers.
Select the desired router, enter the key number and select encryption
type. After that, select “Obtain an IP address automatically” or
manually enter the IP address by clicking “Use the following IP
address”.
⑤ Pull the network cable out of the camera.
⑥ Run the IP-Tool and find the camera through IP address or MAC
address. Then double click it listed in the IP-Tool or enter the IP
address of the camera in the address bar of the web browser to
access the camera.
∅7.5
12.2
4.5
34.5
mm
Plastic plug
Screw
A: You can quickly connect Wi-Fi through WPS function (See 3
Overview--WPS for more details).
B. You can also follow the steps below to connect Wi-Fi.
Enable
Index SSID Working Mode Security Mode Channel Signal Mbps Connection
1 HUAW EI-WLAN Manage WPA2-personal 2 50 150 Unconnected
WI-FI
SSID
Security Mode
Key 1
Encryption Type
Wi-Fi Networks Search
HUAW EI-WLAN
WPA2-pe rsonal
AES