TVT TD-9521E3 User manual

Package
Overview
Installation
1
2
3
4
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Do not directly touch the camera when installing.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Quick Start Guide
Network Camera
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug Screwdriver
Tapping screws × 4
Ethernet connector
Audio input connector
Alarm input/output
Power connector
Reset
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment. You'd better install back the lower
dome less than 4 hours after removing it. Do not remove the protection
film until finishing the installation.
① Attach the drill template to the place where you want to fix the camera
and then drill the screw holes and the cable hole on the wall according
to the drill template.
2
13
Micro SD Card Slot
Security Cap
■ Please read this instruction carefully before operating the unit
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
74.3
74.3
1
2
3
4
5
6
(mm)
1
2
3
4
5
6
DC12V
ALARM
4 3 2 1
ALARM
4 3 2 1
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
● Connecting Network Cable
●
Alarm Input: Join the grounding ends of the sensor and the camera and then
connect the signal cable of the sensor to the alarm input port (ALM-INA)
of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then insert the
signal wires of the alarm output devices into the port of OPEN and COM
separately. Finally tighten the screws. Some of the external alarm output
devices need the power supply.
Alarm Connection

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
● Access Through IP-Tool
In LAN, there are two ways to access the camera. 1. Access Through
IP-Tool; 2. Direct Access Through WEB Browser
① Make sure that the camera and the PC are connected to the local
network.
② Install the IP-Tool from the CD and run it after installation.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure
its network address is in the same local network segment as the
computer’s. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
modification, please enter the password of the administrator and click
“Modify” button to modify the settings.
The default password of the administrator is “123456”.
④ Double-click the IP address and then the system will pop up the
web browser to connect IP-CAM. Follow directions to download
and install the plugin in the computer. Then enter the user name and
password in the login interface.
● Direct Access Through WEB Browser
450043001271 A0
The default username is admin; the default password is 123456.
③
④ Route and connect the cables.
⑤ Secure the camera to the wall with screws provided as shown
below.
Loosen the screws to open the lower dome.
Rotation 0°~355°
Pan 0°~355°
Rubber Plug
Lower dome
Tilt 0°~67°
⑥
the camera on a monitor and then adjust the camera according to
the figure below to get an optimum angle.
Three-axis adjustment. Before adjustment, view the image of
⑦
screws. Then put the trim ring onto the lower dome and then rotate
it clockwise until it is locked.
Install the lower dome back to the camera and fix it with the
Transparent Dome Maintenance
Transparent dome is an optical element which is made of plastics. As dirt,
dust or fingerprints on the dome will reduce the clarity of the image, please
keep it clean in the course of installing or using but do not directly touch or
wipe it. If there is any dirt or dust, please follow these cleaning tips to clean
your dome camera.
* If there is dust on the dome, please use a dry soft brush to gently brush it .
* If there is water or grease on the dome, please gently wipe off the water or
grease with a soft cloth. Then use another clean cloth with a little neutral
detergent to wipe it several times until it is clean. Finally, dry it with a soft
cloth.
* If there are fingerprints on the dome, please use a clean cotton cloth or lens
cleaning wipe with a little neutral detergent to wipe it several times and
then dry it with a soft cloth.
Tips
① Make sure that the camera and the PC are connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool.
③ Modify the IP address and make sure its network address is in the
same local network segment as the computer’s.
④ Open your web browser and enter the modified IP address in the
address bar to log in the web client. Follow directions to download
the plug-in in the computer. After that, enter the default user name
and password to log in.
Trim ring
② Rotate the trim ring anticlockwise to remove it from the camera.
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After