Twyford SF1261CP Instructions for use

Please retain this document
for future reference.
This product should be fitted
in compliance with Water
Regulations, by a qualified
plumber.
Use only a clean damp cloth
to maintain the surface finish,
use of abrasive cleaning
materials will invalidate your
guarantee.
SOLA SHOWER RAIL, HOSE & HANDSET
Installation Instructions
& Maintenance Guide
SFCPSFCP
IMPORTANT: Please read all of the
instructions before installation.

P2
Select location for kit, ensuring no wiring or pipework
in the wall can be damaged, also that when the slider
bracket is positioned at the top of the rail, the hose is
not over extended.
The location should also ensure that during use, the
water flow is directed toward a suitable location, so as
not to cause water damage.
Remove the caps from the front of the end brackets,
using a sharp blade, taking care not to damage the
product.
Place both end brackets on the rail and position as
required and mark drill holes.
Drill holes in marked position and insert wall plugs.
Place the slider bracket onto the rail, ensuring the
wider opening of the handset holder is located
upwards.
Fit the hose retainer and soap dish to the rail.
Fit both end brackets and locate assembled rail over
the drill holes.
Place wall screw through top end bracket and loosely
fit to the wall.
Place screw through bottom end bracket and then
secure assembly to the wall.
Select location for kit, ensuring no wiring or
pipework in the wall can be damaged, also
that when the slider bracket is positioned at
the top of the rail, the hose is not over
extended.
The location should also ensure that during
use, the water flow is directed toward a
suitable location, so as not to cause water
damage.
Remove the caps from the front of the end
brackets, using a sharp blade, taking care not
to damage the product.
Place both end brackets on the rail and
position as required and mark drill holes.
Drill holes in marked position and insert wall
plugs.
Locate hose retainer and soap dish as
required.
To locate the slider bracket, ensure that
slider handle is turned to release the bracket,
before attempting to move along the rail,
failure to this will damage the rail surface.
Ensure that the rail is fully secured to the wall
before fitting handset.
Fit chrome end caps to both top and bottom
brackets.
Place the slider bracket onto the rail,
ensuring the wider opening of the handset
holder is located upwards.
Fit the hose retainer and soap dish to the rail.
Fit both end brackets and locate assembled
rail over the drill holes.
Place wall screw through top end bracket and
loosely fit to the wall.
Place screw through bottom end bracket and
then secure assembly to the wall.
Fit hose seals to both ends of shower hose.
Thread the hose through the hole in the hose
retainer.
Screw the cone end of the hose to the
handset.
Screw the opposite end of the hose to the
mixer.
Locate the hose cone into the slide bracket,
ensuring that it is fully inserted.
If the cone is not fully inserted, the handset
may fall out during use.
To adjust the angle of the handset, gently
move the handset just above the slider.
DTC INST201 - ISSUE 1 (11.5.11)
Select location for kit, ensuring no wiring or
pipework in the wall can be damaged, also
that when the slider bracket is positioned at
the top of the rail, the hose is not over
extended.
The location should also ensure that during
use, the water flow is directed toward a
suitable location, so as not to cause water
damage.
Remove the caps from the front of the end
brackets, using a sharp blade, taking care not
to damage the product.
Place both end brackets on the rail and
position as required and mark drill holes.
Drill holes in marked position and insert wall
plugs.
Locate hose retainer and soap dish as
required.
To locate the slider bracket, ensure that
slider handle is turned to release the bracket,
before attempting to move along the rail,
failure to this will damage the rail surface.
Ensure that the rail is fully secured to the wall
before fitting handset.
Fit chrome end caps to both top and bottom
brackets.
Place the slider bracket onto the rail,
ensuring the wider opening of the handset
holder is located upwards.
Fit the hose retainer and soap dish to the rail.
Fit both end brackets and locate assembled
rail over the drill holes.
Place wall screw through top end bracket and
loosely fit to the wall.
Place screw through bottom end bracket and
then secure assembly to the wall.
Fit hose seals to both ends of shower hose.
Thread the hose through the hole in the hose
retainer.
Screw the cone end of the hose to the
handset.
Screw the opposite end of the hose to the
mixer.
Locate the hose cone into the slide bracket,
ensuring that it is fully inserted.
If the cone is not fully inserted, the handset
may fall out during use.
To adjust the angle of the handset, gently
move the handset just above the slider.
DTC INST201 - ISSUE 1 (11.5.11)

P3
Locate hose retainer and soap dish as required.
To locate the slider bracket, ensure that slider handle
is turned to release the bracket, before attempting to
move along the rail, failure to this will damage the rail
surface.
Ensure that the rail is fully secured to the wall before
fitting handset.
Fit chrome end caps to both top and bottom brackets.
Fit hose seals to both ends of shower hose.
Thread the hose through the hole in the hose
retainer.
Screw the cone end of the hose to the handset.
Screw the opposite end of the hose to the mixer.
Locate the hose cone into the slide bracket, ensuring
that it is fully inserted.
If the cone is not fully inserted, the handset may fall
out during use.
To adjust the angle of the handset, gently move the
handset just above the slider.
If required the 8 litre per minute flow regulator
should be fitted between the hose and handset
instead of the rubber washer.
Select location for kit, ensuring no wiring or
pipework in the wall can be damaged, also
that when the slider bracket is positioned at
the top of the rail, the hose is not over
extended.
The location should also ensure that during
use, the water flow is directed toward a
suitable location, so as not to cause water
damage.
Remove the caps from the front of the end
brackets, using a sharp blade, taking care not
to damage the product.
Place both end brackets on the rail and
position as required and mark drill holes.
Drill holes in marked position and insert wall
plugs.
Locate hose retainer and soap dish as
required.
To locate the slider bracket, ensure that
slider handle is turned to release the bracket,
before attempting to move along the rail,
failure to this will damage the rail surface.
Ensure that the rail is fully secured to the wall
before fitting handset.
Fit chrome end caps to both top and bottom
brackets.
Place the slider bracket onto the rail,
ensuring the wider opening of the handset
holder is located upwards.
Fit the hose retainer and soap dish to the rail.
Fit both end brackets and locate assembled
rail over the drill holes.
Place wall screw through top end bracket and
loosely fit to the wall.
Place screw through bottom end bracket and
then secure assembly to the wall.
Fit hose seals to both ends of shower hose.
Thread the hose through the hole in the hose
retainer.
Screw the cone end of the hose to the
handset.
Screw the opposite end of the hose to the
mixer.
Locate the hose cone into the slide bracket,
ensuring that it is fully inserted.
If the cone is not fully inserted, the handset
may fall out during use.
To adjust the angle of the handset, gently
move the handset just above the slider.
DTC INST201 - ISSUE 1 (11.5.11)
Select location for kit, ensuring no wiring or
pipework in the wall can be damaged, also
that when the slider bracket is positioned at
the top of the rail, the hose is not over
extended.
The location should also ensure that during
use, the water flow is directed toward a
suitable location, so as not to cause water
damage.
Remove the caps from the front of the end
brackets, using a sharp blade, taking care not
to damage the product.
Place both end brackets on the rail and
position as required and mark drill holes.
Drill holes in marked position and insert wall
plugs.
Locate hose retainer and soap dish as
required.
To locate the slider bracket, ensure that
slider handle is turned to release the bracket,
before attempting to move along the rail,
failure to this will damage the rail surface.
Ensure that the rail is fully secured to the wall
before fitting handset.
Fit chrome end caps to both top and bottom
brackets.
Place the slider bracket onto the rail,
ensuring the wider opening of the handset
holder is located upwards.
Fit the hose retainer and soap dish to the rail.
Fit both end brackets and locate assembled
rail over the drill holes.
Place wall screw through top end bracket and
loosely fit to the wall.
Place screw through bottom end bracket and
then secure assembly to the wall.
Fit hose seals to both ends of shower hose.
Thread the hose through the hole in the hose
retainer.
Screw the cone end of the hose to the
handset.
Screw the opposite end of the hose to the
mixer.
Locate the hose cone into the slide bracket,
ensuring that it is fully inserted.
If the cone is not fully inserted, the handset
may fall out during use.
To adjust the angle of the handset, gently
move the handset just above the slider.
DTC INST201 - ISSUE 1 (11.5.11)

Your product has a high quality finish and should be treated with care to preserve the
visible surfaces.
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly
with contamination free warm soapy water and a damp soft cloth. Do not use products
containing chlorine bleach or hydrochloric acid as these can damage the product.
Always rinse the product thoroughly after cleaning to remove cleaning products that
can damage the product finish.
Your product comes with a 1 year guarantee, proof of purchase is required.
The guarantee does not cover faults or damage caused by incorrect installation and/or
maintenance, ordinary wear and tear, water composition etc. including:
Supply pipes reversed, Incorrect pressure or temperature, *Incorrect use, Foreign
bodies and/or scale due to the water composition, Incorrect cleaning.
We have a policy of continuous improvement and reserve the right to change
specifications without notice
INST SF1261CP/SF1256CP – V1
Twyford Bathrooms Registered Office
Geberit House
Edgehill Drive
Warwick
Warwickshire
CV34 6NH
Part of the Geberit Group
UK Technical Helpline
TEL: [phone]
E: [email protected]
www.twyfordbathrooms.com