Tyent NMP Series User manual

User Manual
WATER IONIZER
MADE IN KOREA
This product is intended for domestic use only.
Keep this user manual handy for easy reference.
Carefully read this User Manual, particularly “all safety warnings.”
■
■
■
pH Chart
How to Measure: Place 10-15 mL of test water in a container
and add 2-3 drops of reagent. Then mix well and check the
color of the water with the pH chart above.
(The color depends on water quality and reagent.)
The user should be responsible for failure or
improper selection or improper use of the
products such as use in any manner for which
the product was not originally intended.
This product is subject to changes that enhance
its performance without prior notification.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
This appliance is not intended for use by persons (including
children) with reduced physical sensory or mental capabilities
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
100-130V

To Our Valued Customers Table of contents
23
Table of Contents To Our Valued Customers
To Our Valued Customers
Table of Contents
Before Usage
Safety Precautions and Warnings
Product Features
Package Contents
Unit Overview
LCD Display and Touch Pad Overview
How to Install the Unit
Water Hose Installation
Directions for Product Use
System Setup Mode
Cleaning Function
Customer Serviceable Parts
How to Change the Filters
How to Reset the Filters
TURBO Function
Unit Specifications
Troubleshooting
Product Warranty
2
3
4
5
10
12
13
14
16
18
20
22
24
25
26
27
28
29
30
31
o Our Valued Customers
able of ContentsT
ntended UseI
Thank you for purchasing the NMP series Water Ionizer .
Please read all safety warnings and this User Manual carefully before using this product
to ensure proper product usage. (Keep the manual handy for easy reference.)
This device creates
functional alkaline ionized water . It changes the properties
of regular tap water through the use of electrolysis. Following are the changes normal
tap water undergoes via this process:
We are not responsible for any accidents and/or malfunctions due to the
improper use of this machine
Please keep the manual and warranty card in a safe place, so that it’s
easily accessible when you need it
Please refer to this manual often when you have questions when using or
when troubleshooting this unit
An increase or decrease in pH level
Creation of negatively charged hydrogen ions (antioxidants)
Purification through filtration
T

45
Before Usage Safety Precautions and Warnings
afety Precautions and WarningsS
Do not use if the power cord is damaged or in a
loose power outlet.
Do not pull the power cord. Never touch the power
cord or the power outlet with wet hands.
Do not forcibly bend, squeeze, damage or crush
the power cord under heavy objects.
Unplug the power cord during general maintenance,
repair and inspection and while replacing parts.
Do not use power surge protectors with this unit.
Use unit with its own dedicated power source.
Regarding the Power Supply
efore UsageB
Safety precautions are provided for the safe and proper use of this unit and can prevent
danger, bodily harm and/or possible damage due to misuse. Please make sure you are
familiar with all the safety precautions and warnings associated with this unit.
Do not drink functional water with medication. When taking medication, use “clean H2O”
filtered water thirty minutes prior to taking medication as well as with medication.
You may resume drinking functional water thirty minutes after taking medication.
Always consult your primary care physician before drinking functional water. Only
drink a small amount near a neutral pH level for the first week. This will give the body
time to adjust to functional water during the detoxification period. See Welcome
Guide for full details on getting started.
If you notice any negative effects from drinking functional water, stop drinking the
functional water immediately and consult your primary care physician about
changes in your body’s pH level.
If you are currently under the care of a primary care physician for an existing condi-
tion, consult your primary care physician about how changes in pH and other
characteristics of functional water could affect your medical condition.
If you suffer from gastric anacidity, kidney failure or potassium excretion, you should
not drink functional water.
Verify the pH levels of the functional water dispensed from this unit on a monthly
basis to ensure proper function. This can be done with the supplied reagent drops
and a pH color chart.
When switching from one pH to another, it is good practice to let the water run for
several seconds before using.
It is common to drink half your body weight in ounces. For example, if you weigh 180
pounds, it may be wise to drink 90 ounces every day of water per day. This especially
applies after you have given your body some time to adjust to the new pH level.
The recommended drinking level for functional water is 9.5 pH (+-0.3). It is not
recommended to drink functional water above a pH of 10.
If you wish to store functional water, use a glass or other nonleaching material with
an airtight lid and store it in the refrigerator. Functional water will begin to weaken
immediately and will lose most of its benefits after 3 days.
Never run hot water through this unit.
Never drink acidic water.
DANGER (Red Warning Sign) indicates an imminent hazard that could result in serious injury
or death. If you see this sign, stop using this unit immediately.
WARNING (Orange Warning Sign) indicates a potential hazard that could result in significant
bodily harm or damage to the unit. If you see this sign, stop the use of this unit.
ATTENTION (Yellow Warning Sign) indicates a potential hazard that could result in minor
bodily harm or damage to the unit.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Before Usage Safety Precautions and Warnings

67
Safety Precautions and Warnings Safety Precautions and Warnings
To reduce the risk of electric shock, do not remove
the cover; there are no user-serviceable parts
inside. Refer servicing to qualified service person-
nel. Removing the cover will void the warranty.
Only use the unit with the correct voltage.
Do not place this unit near heat sources.
Do not place this unit on an uneven surface.
Do not drop or use excessive force on this unit.
Do not connect the water line to a hot water supply.
Do not use unfit raw water in accordance with the
standards of the water service act.
Installation
Do not use in areas of high humidity and/or high
temperature.
Usage
Install the drain faucet near sink and adjust the
position of drain faucet to drain away to the sink.
Make sure the drain faucet is positioned lower than
the unit.
Do not discharge water over 1 hour.
If the unit won't be used for a long time, shut off the
valve and unplug the power cord.
If you hear strange noises, smell a burning odor or
see smoke, unplug the power cord immediately
and call qualified personnel for service.
Replace filters every 6 months to optimize the purifica-
tion performance of this unit even if the replacement
indicator light isn’t turned on.
If the unit is not used for a few days, let the water run
for 1-2 minutes before drinking functional water.
Safety Precautions and Warnings Safety Precautions and Warnings
Turn off

89
Safety Precautions and Warnings Safety Precautions and Warnings
Do not poke or scratch the touch pad or LCD
display with sharp objects.
Do not place any objects on top of this unit no
matter how small they are.
If water leaks out of the unit (other than the
hoses) or if the unit is standing in a puddle of
water, shut off the water supply, unplug the
power cord and contact qualified service personnel
for service.
Do not use alkaline or acidic water in fish bowls
or aquariums. The sudden change in pH could
be harmful or fatal to some marine life.
In areas of hard water (calcium scaling present
on faucets), notify your service provider and
install a cell safe antiscale prefilter to protect the
ionizer from scaling.
It is beneficial for the maintenance of the
machine to run a strong acidic level for 5-minute
cycles twice weekly. This will help to maintain a
clean chamber.
It is normal for condensation to be present on the
unit during humid summer months. If condensa-
tion persists despite weather conditions, unplug
the power cord and refer servicing to qualified
service personnel.
Turn off
Cleaning
Do not store the unit near chemicals, food,
metals or medication
Do not spray water on the main unit. Do not
clean the unit with benzene or other chemicals,
which may leak into the unit. If using a damp
cloth, be very careful not to get electronic display
wet.
Storage
If the original packaging is not available, cover
the unit in plastic to avoid scratching the surface.
Store the unit in its original packaging in a cool,
dry place when not in use.
Carefully remove this unit from its packaging.
Keep the original packaging for future storage
and unit transportation.
Remove the filters and turn them upside down to
remove excess water before storing.
Safety Precautions and Warnings Safety Precautions and Warnings

10 11
Product Features Product Features
Product Features Product Features
roduct FeaturesP
Fully automatic system with embedded central
processing unit (CPU)
Every aspect of creating functional water is controlled by the CPU
chip that automatically finds an optimal operating condition using.
Fixed quantity discharge function
It generates desired amount of water by convienet operation.
SMPS type power supply
A CPU monitors the power that is supplied to different parts of
the unit, thereby ensuring efficient performance.
Automatic water flow
Simply pressing the touch button allows you to start and stop
the flow of functional water.
Voice announcement
Voice announcement for different functions and safety warnings
ensure safe and convenient use.
RTR(Real Time Refresh)
Automatic cleaning function
Unit features an automatic plate cleaning function using polarity
oscillation.
Automatic Stop Function
15 minutes after a function is selected, water outflow will stop to
prevent overflow or flooding.
Temperature Sensor Function for Safe Operation
If the temperature of the source water exceeds 95℉(35℃) then
water will stop flowing and a warning message will appear on
the screen.
Eco mode
The LCD backlight will be turned off automatically during periods
of non-use and the Time function is displayed.
Filter replacement cycle
This unit features a filter life cycle display and voice announce-
ments designed to let you know when it is time to change the
filters. Every 6 months is best for optimal performance.
Touch LCD display color backlight
The color back light on the LCD display allows you to distinguish
alkali water from acidic water.
Advanced water purification system
The advanced performance of the primary filter and functional
secondary filter enable optimal purifying conditions for tap water.
Detects if filter door is open
When door is open, the water supply will be suspended for your safety.
15min
Safety Functions
The outflow of functional water stops automatically when raw water is not
supplied, preventing the electrolytic cell and power supply unit from being
damaged due to current overflow, water from being wasted and accidental
water leaks. This function also allows you to set pH and ORP levels according
to the amount of water inflow, to distinguish pH from backlight colors and set
the auto cleaning function.

12 13
Unit Overview Package Contents
Package Contents Unit Overview
ackage ContentsPnit OverviewU
Tools You Will Need
Make sure you are familiar with the parts and features of this unit, and carefully read
the user manual and other important information
Water Outlet Tube
Water Ionizer
Faucet Diverter
pH Testing
Solution Bottle
8.2 ft (2.5 m)
of Hose
Tube Suction Cup
Assortment of Connectors
and Rubber Washers
Adjustable
Wrench
Utility
Scissors Plumber’s Tape
Front View
Water Outlet Unit
LCD Display
Front Cover
Door Case
Front Case
Water Outlet Tube
JOG Dial
①
②
③
④
⑤
⑥
⑦
①
②
③
①
②
Rear View
Hanging Groove
Rear Case
Power Cord
Bottom View
Water Inflow
Water Outflow
Wrench
1
56
4
7
2
12
3
2
3
1
(Model: NMP-9000T, S11T, S13T)
Drain Faucet
+ Tube Suction Cup
Stem ElbowTube Elbow
-Drain Hose
-User Manual

LCD Display and Touch Pad Overview LCD Display and Touch Pad Overview
14 15
How to Install the Unit How to Install the Unit
CD Display and Touch Pad OverviewL
ⓐ ⓑ ⓒ ⓓ ⓔ ⓕ ⓖ
ⓗ
ⓚ ⓝ
ⓘ ⓙ
ⓞ
ⓟ ⓠ ⓡ
ⓢ ⓣ
ⓛ ⓜ
Turbo
Acidic level 2
Acidic level 1
Purify water
Alkaline level 1
Alkaline level 2
Alkaline level 3
ⓐ
ⓑ
ⓒ
ⓓ
ⓔ
ⓕ
ⓖ
ⓗ
ⓘ
ⓙ
ⓚ
ⓛ
ⓜ
ⓝ
ⓞ
ⓟ
ⓠ
ⓡ
ⓢ
ⓣ
Time
pH
Water flow
Voltage/Flow/Time
Door open
Temperature
Remaining time
Fixed quantity discharge
System set up
Cleaning
Volume On / Off
1st Filter reset
2nd Filter reset
When Alkaline Water (1, 2 & 3), Purified Water (H2O), Acidic Water (1 & 2)
and Turbo Water icons are selected, backlight colors are as follows :
Alkaline level 1
Light Alkaline water
Alkaline level 2
Medium Alkaline water
Alkaline level 3
Strong Alkaline water
Purify water
Creates purified water
Acidic level 1
Non-Drinkable
Acidic level 2
Non-Drinkable
Turbo mode
Non-Drinkable
Real Time Refresh
Non-Drinkable
Standby screen1
Water Outflow screen2
Display color3
Backlight of LCD display will match the pH level color according to water pH level
being used after icon is pressed.
Below information will be
rotating on the display.
▶
Selected pH level Amount of
supply water
Remaining
discharge time
※pH value is standard value based on test water.
※Errors may occur between actual output water according to raw water condition such as
water quality, amount of water and temperature.
The selected icon flickers during water outflow.

How to Install the Unit How to Install the Unit
16 17
How to Install the Unit How to Install the Unit
ow to Install the UnitH
Determine whether you will connect the unit directly to the cold water supply line
(under sink) or to the faucet (see image).
Do not turn on the main water supply until all hoses are properly installed to the
unit. The unit and components are subject to change without prior notification in
order to enhance performance.
Many faucets vary in design, and your faucet may require different setup instruc-
tions than those featured in this manual. Please consult a qualified service profes-
sional if you are unable to correctly complete the installation.
Shut off both the hot and cold water main supply at the pipe under the sink.
If your faucet features a screw-on style aerator, remove it by unscrewing it from the tip
of the faucet.
If the included faucet diverter does not fit directly to the tip of the faucet, select an
appropriate size connector and rubber washer (included).
When connecting the diverter or adapter to the faucet, be sure to use plumbing pipe
thread seal tape (not included) to prevent leaks.
If necessary, connect the faucet diverter with the appropriate connector to the faucet.
Be sure all connections are secure but do not overtighten them.
Option A l Faucet: A faucet connection requires a faucet diverter (included).
Option B l Under-Sink: An under sink connection requires an under-sink adapter kit
(not included) or a compatible t-valve (available from most hardware stores). For more
information see Welcome Guide or call support.
Option A – Faucet Installation
①
②
③
④
⑤
⑥
①
②
③
④
⑤
⑥
⑦
Purchase either an under-sink installation kit (not included) or purchase a
T-connection (with shut-off valve) from a hardware or plumbing supply store.
Shutoff both the hot and cold water main supply at the pipe under the sink.
Locate the cold water supply line valve.
Disconnect the faucet cold water supply line from main cold water pipe. Use a towel
to catch the small amount of water that may come from the faucet supply line.
When connecting the T-connection to cold water pipe, be sure to use plumbing
pipe thread seal tape (not included) to prevent leaks.
Reconnect the faucet cold water supply line to the T-connection (now secured to
the main cold water pipe).
Be sure all connections are secure but do not overtighten them.
Option B – Under-Sink Installation
Both Options

Water Hose Installation Water Hose Installation
18 19
Water Hose Installation Water Hose Installation
ater Hose InstallationW
Inflow
① Place the unit on the planned installation location
and screw the flexible tube clockwise into the
water outlet hole positioned at the top of the unit.
Do not over tighten.
Cut an appropriate length of drain hose and
connect it the drain faucet. When drain hose is
connected, put the drain faucet in the inner part
of sink to run water.
Make sure all hose connections are firmly seated
in the correct holes, both on the unit and at the
water supply
Turn on both the cold and hot water supply.
Make sure there are no leaks at any of the
connections. Make sure the faucet is working
with both hot and cold water. Make sure there
are no leaks from the hose connections on the
bottom of the unit. Make sure the hoses are firmly
seated in the unit holes.
②
Press the stem elbows into the water inflow and
outflow holes on the bottom of the unit until you
hear a click and feel the hose sit firmly in place.
③
⑤
⑥
⑦
Measure between where the unit will be located
(on the counter) and the water faucet (or under-
sink T-connection) where the diverter (or
T-connection) will be installed. Cut enough hose
to allow connection from the rear of the unit to
the water supply (either faucet diverter or under-
sink T-connection).
Note: Keep the length under-16 feet (5 meters) from
the unit to the faucet. You may need a pressure pump
or larger size hose if the pressure is too low. Be sure to
leave a few extra inches (centimeters) of length so the
faucet can still be rotated.
④
Connect the hose from the inflow hole to the cold
water supply, either at the faucet diverter (Option
A - remove the nut from the diverter, slide the nut
on to the hose, firmly seat the hose on the faucet
diverter, and screw the nut over the hose and
back on to the faucet diverter) or the under-sink
T-connection.
(Option B: route the hose through the counter-top
to the T-connection, firmly seat the hose on the
T-connection, make sure the connection is sealed
completely)
Inflow Drain
hose to faucet
Be careful not to touch the touch screen at initial
power up. The touch sensor may not operate caused
by touch sensibility change. If the touch sensor does
not operate due to contact with a part of the body,
reconnect the power cord.
Plug in the power cord. You should hear a series
of tones when you power up the unit.
⑧
※
Drain faucet
to sink
Drain

Directions for Product Use Directions for Product Use
20 21
Directions for Product Use Directions for Product Use
irections for Product UseD
When using the Touch screen1
When using fixed quantity discharge function
When using fixed quantity discharge function
When using the Jog dial2
Select a desired water mode.
①
Water Outflow Stop: Lightly touch the blinking icon again to stop water flow.
③
②
Water Outflow: The selected icon flickers during water outflow. If the selected
icon is not pressed again, the unit will automatically stop after 15 minutes of
water outflow.
》 》
15min
15min
》
※NOTE: Remember, a LIGHT TOUCH is all that is required when pressing the LCD.
Touch the QTY,C icon and choose a fixed amount of water. (0.5ℓ, 1.0ℓ,1.5ℓ)
( 0.5 》1.0 》1.5 》release )
Select a desired water mode.
Water outflow stops automatically.
(Fixed quantity discharge function is released after water comes out.)
①
②
③
》 》
Touch the "QTY,C" button.
Select the fixed amount of water you need by turning the jog dial.
- Clockwise : Increasing by 100ml ( Max.5L )
- Counterclockwise : Decreasing by 100ml ( Min. 200ml )
Push the discharge level you need.
Automatic stop after discharging fixed amount of water you selected.
(Discharge of water will stop when you touch the button while water is coming out.)
After water comes out, fixed quantity discharge function is released.
①
②
③
④
⑤
(model: NMP-9000T, S11T, S13T)
Turn Dial either direction to select function.
Push center of Dial to start water outflow. The selected icon flickers
during water outflow.
Push center of Dial to stop water outflow.
①
②
③
》
》 》

The voice icon will disappear by selecting the voice icon in this sequence.
Voice message - On : “ Voice function works ”
Off : “ Voice function terminates ”
System setup mode System setup mode
22 23
system setup mode system setup mode
ystem setup modeS
①
②
2pH Control Function
3Volume Level Adjustment
4Selecting Voice On / Off
③Press F1 to raise pH. Press F2 to lower pH.
(Adjustable by Jog dial)
④Once setup is complete, press the water level
button you selected for 3 seconds.
(beeps 2 times)
1Setting the time
①Change to the system setting mode by pressing
the SET icon on the LCD for 3 seconds.
(beeps 2 times. Voice says ,“System setup mode”)
①Change to the system setting mode by pressing
the SET icon on the LCD for 3 seconds.
(beeps 2 times. Voice says ,“System setup mode”)
①Change to the system setting mode by pressing
the SET icon on the LCD for 3 seconds.
(beeps 2 times. Voice says ,“System setup mode”)
②Press the fixed quantity discharge icon for
3 seconds. (beeps 2 times)
③The mode (AM-Hour-Minute) will be changed by
selecting the fixed quantity discharge icon in this
sequence.
④Press F1 or F2 to set the time.
(Adjustable by Jog dial)
⑤Once setup is complete, press the fixed quantity
discharge icon for 3 seconds. (beeps 2 times)
⑥Push setup icon for 3 seconds to return to
standby screen.
(beeps 2 times. Voice says ,“Setup was completed”)
⑤Push setup icon for 3 seconds to return to
standby screen.
(beeps 2 times. Voice says ,“Setup was completed”)
④Push setup icon for 3 seconds to return to standby screen.
(beeps 2 times. Voice says ,“Setup was completed”)
③Control the voice volume by F1 and F2
button on the bottom. Current voice
volume level is displayed on LCD.
- F1 icon : Volume decrease
- F2 icon : Volume increase
②Press the voice icon to control volume.
②Press the desired water level button for 3 seconds.
(beeps 2 times)
~

Primary Filter: YT20 1st Filter
1st Filter
2nd Filter
ATTENTION: The consumer accepts any and all responsibility and/or liability if
replacement filters and/or purchased parts are not manufacturer specific. This unit
contains high-performance purifying filters and an advanced control system.
The life of the filter can vary greatly due to use, water pressure, water quality and the
changing of the seasons. Filters may need to be replaced sooner than the scheduled time
due to these reasons, you may notice reduced water quality or declining water taste.
Recommended filter replacement cycle:
951.0 gallons (3,600 L) / Every 6 months
Removes harmful chemicals like chlorine,
compounds such as agrichemicals and deter-
gents, large suspended matters like rust and
sediments as well as other volatile organic
compounds through an efficient, an activated
absorption method. It also eliminates bad
smells and any remaining dissolved chlorine.
Secondary Filter: YT20 2nd Filter
Recommended filter replacement cycle:
951.0 gallons (3,600 L) / Every 6 months
Fine artificial film filters contaminated materials
including ordinary bacteria while maintaining
essential minerals in the water.
leaning FunctionCustomer Serviceable PartsC
Other Icon Display Customer Serviceable Parts
24 25
Customer Serviceable Parts Cleaning Function
Performed during water outflow after more than 24 hours of non-operation.
(Note: RTR icon and backlight will flicker before automatic cleaning is performed)
Performed after 30 liters of water outflow. Performed each time power is
turned on.
(Note: RTR icon and backlight will flicker before automatic cleaning is performed)
Press the RTR button on stand-by screen.
The cleaning (Voice message: “It’s under washing, do not drink”)
- Automatic stop: The cleaning will be stop automatically when the washing
time is done.
- Manual stop: The cleaning will be stop when touching the screen during
under washing
The screen changes to the standby screen once the cleaning is done.
①
②
①
②
③
1Auto Cleaning Function (15 Sec)
2Manual Cleaning Function (15 Sec)

ow to Reset the FiltersH
How to Change the Filters How to Reset the Filters
26 27
How to reset the filters how to change the filters
①
②
③
④
⑤
ow to Change the FiltersH
Shut off the water supply to the unit.
Turn the power off and unplug the
power cord. Open the door in front of
the product.
Raise the filter to be replaced and turn
it counter clockwise to remove it.
Put the new filter into the right position
by turning it clockwise.
When installing the filter, the connec-
tion bump of the head and the connec-
tion groove on the top of the filter
should be completely combined.
Close the door, plug the power cord
back in, reengage the water supply
and switch the unit back on.
Close
Open
①
②
③
④
⑤
Replace the target filter.
After replacing the filter, press the F1 icon for 3 seconds.
Selected filter is initialized and beeps twice.
Voice announcement : "1st Filter / initializing was performed."
Next, press the F2 icon for 3 seconds.
Selected filter is initialized and beeps twice.
Voice announcement : "2nd Filter / initializing was performed."
Filter usage is displayed in 0 percent(0%) when the filter is
initialized properly.
The water outflow selection mode is available for operation.
After initializing the filter, press the H 2 O button and run purified water for 3minutes.
You are highly recommended to follow this process to use the machine properly.
Unless the quantity filtered is reset, the corresponding filter replacement
message keeps responding.

Turbo Function Unit specifications
28 29
Unit specifications Turbo function
urbo FunctionTnit specificationsU
The TURBO function allows you to create strong alkaline and strong acidicwater.
These types of waters are ONLY to be used for cleaning, sanitizing, and disinfecting
purposes. NEVER DRINK THESE TYPES OF WATER.
TURBO
Strong Acidic Water
pH 2.5
~ pH 3.8
Used to Disinfect
and Sterilize
TURBO
Strong Alkaline Water
pH 10.0
~ pH 11.8
To remove stains from
fabrics/carpet/upholstery.
Alkaline Turbo Water Outflow Acidic Turbo Water Outflow
※To make the best functionality, there may be some change without notices.
NMP-5000T NMP-7000T NMP-9000T NMP-S11T NMP-S13T
Max 220W
O
5 7 9 11 13
Water Cell Plate
Materials
Water Ionizer
100 -130 V~ , 200 -240 V~ / 50-60 Hz
4 -35ºC ( 39 - 95ºF )
0.1- 0.5 MPa
3 Alkaline, 1 Neutral, 2 Acidic, Turbo
User adjustable pH levels control
2 Filters System
LCD filter replacement and announcement
Platinum and Titanium
W300 x D135 x H355 mm (11.8 x 5.3 x 13.9 inches)
approx 5.0kg (11.1 Lbs )
Product Name
Rated Voltage
pH Levels
Adjustable pH
Filters Confihuration
Filter Life Display
Product Size
Product Weight
Electrolytic Cell
Quantity of Poles
Power
Consumption
Operating
Pressure Range
Available
temperature
Model Number
TURBO Function
v
The waters produced in TURBO mode are not intended for drinking.
DO NOT DRINK these types of waters.
●
DO NOT Use the TURBO function in a manner other than directed.
●
While operating the TURBO function, the machine will automatically
stop dispensing water after 5 minutes. This feature prevents accidental
overflow or flooding.
●

Troubleshooting
30 31
Product warranty Troubleshootingn
roubleshootingT
The screen turns o.
Symptoms
Abnormal Taste
Water Outow Change
Incorrect pH levels
Unit stops during use.
Unit leaks.
Settlement in extracted water.
The Unit doesn’t not operate
in cleaning mode.
Only puried water is extracted.
Filter replacement icon
remains“on”even after
lter has been replaced
Checkpoints Measures to be Taken
Check period of use.
Check lters for clog.
Run unit for one minute, draining stagnant
water.
Check lter for replacement time.
Check if the lter ow rate is initiated.
Check lter for proper mounting.
Check other areas of unit.
Check for excessive calcium in source
water.
Check if amount of working water
exceeds 30ℓ.
Check if operating time exceeds 24 hrs.
Check if non-operating time
exceeds 10 minutes.
Check if cleaning icon is pressed.
Check water for solidity. Water quality varies by region.
Reduce amount of raw water.
Contact us. Request after-sales service.
Initialize lter ow rate.
(System setting mode.)
or Request service
Unit stops automatically after 15 min.
Unplug unit. Contact us.
Contact us for additional lter.
Contact us to install a pressure reducing
valve.
The unit returns to normal after performing
auto cleaning for 15 seconds.
When non-using the unit for
10 minutes, it changes to the ECO mode
automatically. The unit returns to
normal after touching the screen.
Check ow rates for higher levels.
Check if amount of drained water is
small.
Check if hose is bent or folded.
Check if ow rates are low.
(less than 1ℓ/ min.)
Check if water supply is cut o or if the
water supply line is frozen.
Check if the operating time exceeds
15 min. ※Turbo : 5 min
Check if valve on water supply is closed.
Replace lter.
Open Valve.
Stretch out hose.
Change lter.
Contact us to install water pump.
Wait until water comes out of the water
supply pipe.
Check if ow rate is high. (5kgf/cm
or faster.)
2
Product Warranty
1. This product features alifetime warranty. If any manufacturing defects or
spontaneous failures occurduring the warranty period, the unit will be
repaired or replaced at no charge.
2. If any failure occurs, please call the service center. Note: The answers to
many service questions can be found online at tyentusa.com/support.
3. In case of a failure resulting from the customer’s negligence or intentional
damage of the product, the customer shall be responsible for repair or
replacement costs.
4. This warranty is non-transferable and valid only for the original owner.
Product Name
Customer’s Name/Phone
Customer’s Address
Date of Purchase
Installation Date/Name
Water Ionizer Warranty Period
Tyent Water Ionizer Lifetime
(Above conditions apply)
Toll Free: 855-TYENT-US
Tyent USA, LLC
www.tyentusa.com
Product Warranty
□EDGE-9000T