U-Prox IP500 User manual

U-Prox IP500 Smart Handle
Installation manual
Features
Power 3 AAA alkaline batteries
32000 openings after battery replacement
2 years operation after battery replacement
Built-in ASK and FSK reader
Direct operation with U-Prox IC L panel at 915.5-927.5 MHz
oGuaranteed range 6 - 20 m
oU-Prox HE and U-Prox HW repeaters for range extension
Door contact input
Request-to-exit on inner door handle
Adjusted with U-Prox IP software
Real-time clock
Non-volatile memory:
IDs
3000
Time zones
250
Permanent
1000
Weekly schedules
250
Temporary
2000
Holidays
250
Events
6000
Temperature range: 0 - +55 0C at 80% relative humidity.
Maximum relative humidity 80% without condensation
Changing the locking side
It is possible to install U-Prox IP 500 Smart Handle both on right hand door or on left hand door (see examples on Fig. 1)
Fig.1. Handing Examples
U-Prox IP 500 Smart Handle supplied for without defined door side. To set handles into position for installation on desired door side
proceed:
A. Outer escutcheon (See Fig. 2)
1. Release stopper rotating it on 900
2. Alter handle position
3. Return stopper to initial position
B. Inner escutcheon
1. Alter handle position
2. Fix it with handle fixing screw
RIGHT HAND
REVERSE
RIGHT HAND
- Direction of access
LEFT HAND
REVERSE
LEFT HAND
Fig. 2. Alter handle position for outer
escutcheon

Installation sequence
Before installation remove old mortise lock and escutcheons, mark and drill holes and mortises in the door according to the lock
installation manual and template, supplied with Smart Handle
Mount strike according to the mortise lock installation instruction
DO THIS ONLY IF DOOR CONTACT WILL BE USED, OTHERWISE SKIP THIS STAGE
make opening for door contact and its wiring as shown below and install supplied Request-To-Exit micro switch according to
instructions below
Door contact installation
Fig. 3. Cable running model for Lockwood 3582 Mortise Lock (left) and for Lockwood 3572 Mortise Lock (right)
Door contact connection
Panel has one terminal for door contact connection. Loop is normal when
shorted that means that door is closed and signals the door opening on
breakage.
Normally panel supplied with Request-To-Exit and Door contact switched
OFF. To use Door contact install Request-To-Exit micro switch and enable
Door contact supervision during its adjustment in U-Prox IP software.
Panel defines the access point state with the door contact. It is impossible
to detect the door forced open or door opened too long access point states
without the door contact proper operation.
Panel generates the “Entry occurred” message on inner handle press when
the door contact is absent. To enable door contact set the Z1 zone as ‘Door
A’ pass direction detector.
Request-To-Exit contact connection
Normally panel supplied without installed Request-To-Exit sensor. In this
case, you must adjust Request-To-Exit micro switch on inner escutcheon
according to the figures below:
1. Unscrew 4 screws fixing handle release mechanics (Fig. 4)
2. Install micro switch into the correct position (Fig. 5)
3. Install handle release mechanics back on its place.
Warning!!! Remove the dividing washer from 3572 lock to allow the spindle to go through the lock.
Warning!!! If the door contact connected and Request-To-Exit micro switch hasn't been installed any door opening with the
inner handle generates an event FORCED DOOR OPEN.
unscrew
unscrew
Fig. 4. Opening handle release mechanics
Fig. 5. Installing microswitch
Opening for Door Contact
wire

Install the mortise lock and fix it with screws according to the mortise lock installation instruction
Install the outer escutcheon and run connection wire through the prepared for it opening
Connect magnetic door contact to the DC terminal on the Battery Holder PCB (optionally)
Connect controller wiring to the Battery Holder PCB
Install inner escutcheon. Take care that rectangle spindle fell into corresponding holes in the mortise lock and outer escutcheon
precisely
Fix inner and outer escutcheons with screws
Insert the cylinder (if used) and secure it according to mortise lock installation manual
Place the batteries into the battery holder following the polarity
Put on the cover of the inner escutcheon and fix it with screw, rotating it counterclockwise (unscrew)
Place the inner handle on the rectangle and fix it with screw
Add the panel to the access control system database according to the access control system manual
Download panel from the access control system according to the access control system manual
+
+
+
-
-
-