Ubiquiti airFiber AF 60 User manual

Dish Main Arm Stabilizer Arms (Qty. 2)
Mounting Bracket Screw U-Clamp
Package Contents
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Flat Washers (Qty. 2) Lock Washers (Qty. 2) Flange Nuts (Qty. 2)
Gigabit PoE (24V, 0.5A) with
Mounting Bracket
Power Cord
Installation Requirements
Clear line of sight between airFiber AP and station
Clear view of the sky for proper GPS operation
Vertical mounting orientation
Mounting point:
At least 1 m below the highest point on the structure
For tower installations, at least 3 m below the top of the tower
Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are
required for all wired Ethernet connections.
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the airFiber
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

radio and the other at the entry point to the building. The ETH-SP-G2 will absorb
power surges and safely discharge them into the ground.
Hardware Overview
Note: For guidelines about grounding and lightning protection, follow your
local electrical regulatory codes.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

GPS LED
60G LED
5G LED
Blue
The LED will light blue when the GPS signal strength
is sufficient. This requires a minimum of three GPS
satellite connections.
Blue The LED will light blue when the 60 GHz link is ready.
Blue The LED will light blue when the 5 GHz link is ready.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

LAN LED
Power LED
PoE IN
Reset Button
Blue
The LED will light steady blue when an active
Ethernet connection is made to the Ethernet port and
flash when there is activity.
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti® Network
Management System (UNMS™). See “UNMS
Management”.
Blue Ready for use, connected to UNMS.
Steady Blue with
Occasional Flashing
Ready for use, unable to connect to UNMS, check
connection to UNMS server.
Quickly Flashing Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
Gigabit Ethernet PoE port for handling all user traffic and powering the device.
Default IP address: 192.168.1.20.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.
Installation Overview
We recommend configuring both airFiber radios (Access Point and Station) before site
installation. Follow the instructions in “Configuration” for each radio.
Configuration
Connecting Power over Ethernet
1.
2.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.
Configuring the Settings
The device is set to DHCP by default, so it will try to automatically obtain an IP address.
If that fails, it will use the default fallback IP address, 192.168.1.20. Proceed to the
appropriate section, “DHCP” or “Fallback IP Address”:
DHCP
Use one of the following methods:
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Set up the DHCP server to provide a specific IP address to the device based on its
MAC address (on the label).
Let the device obtain an IP address and then check the DHCP server to see which IP
address was assigned.
1. Launch your web browser. Type the appropriate address in the address field.
Press enter (PC) or return (Mac).
2. Select your Country and Language. You must agree to the Terms of Use to use
the product. Click Continue.
3. Enter a Username and Password, confirm the Password, and click Save.
4. Click the icon.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

5. Configure the following settings:
a. For one airFiber radio, enable Access Point mode. For the other airFiber radio
(the Station), keep Access Point disabled.
b. Enter a name in the SSID field. This must be the same on both the AP and the
Station.
c. In the WPA2 Preshared Key field, enter a combination of alphanumeric
characters (0-9, A-Z, or a-z).
6. Click Save Changes.
7. Configure each airFiber radio with a unique IP address:
a. Click the icon.
Note: The key is an alphanumeric password between 8 and 63
characters long.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD