Ubiquiti LiteBeam LBE-5AC-LR User manual

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 1/23
Antenna Feed Center Reflector Panel Side Reflector Panels (Qty.
2)
Mounting Bracket Feed Receiver Pivot Panels (Qty. 2)
M4 SEM Screws (Qty. 8) M8 SEM Screws (Qty. 4) Metal Straps (Qty. 3)
Gigabit PoE (24V, 0.3A) with
Mounting Bracket
Power Cord
Package Contents
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 2/23
Installation Requirements
Phillips screwdriver
13 mm wrench
7 mm socket wrench or screwdriver
Shielded Category 5 (or above) cabling with drain wire should be used for all
wired Ethernet connections and should be grounded through the AC ground of
the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded
Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend
that you use two Ethernet Surge Protectors, model ETH-SP, one near the
LiteBeam and the other at the entry point to the building. The ETH-SP will
absorb power surges and safely discharge them into the ground.
Application Examples
The LiteBeam AC mounted outdoors with the reflector installed provides
directional outdoor coverage (gain reflector-dependent).
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 3/23
The LiteBeam AC mounted outdoors without the reflector installed provides
outdoor-to-indoor coverage using the 3 dBi Antenna Feed only.
Hardware Overview
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 4/23
Ethernet LED
Power LED
Reset Button
Ethernet Port
The LED will light steady blue when an active Ethernet connection is made and
flash when there is activity.
The LED will light blue when the device is connected to a power source.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the LiteBeam AC is powered on. The LiteBeam AC may also be
reset remotely using the auxiliary Reset button located on the bottom of the
Gigabit PoE adapter.
Supports 10/100/1000 connections and passive PoE. This port should be
connected to the LAN and DHCP server.
Hardware Installation
1.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 5/23
2.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 6/23
3.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 7/23
4.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 8/23
5.
6.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 9/23
7.
8.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents

5/4/2021 LBE-5AC-LR Quick Start Guide
https://dl.ubnt.com/qsg/LBE-5AC-LR/LBE-5AC-LR_EN.html 10/23
9.
10.
LBE-5AC-LR Quick Start Guide
×
Click for
Table of Contents