Ubiquiti LTU-Pro User manual

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
LTU-Pro Mount Bracket Bracket Clamp
Bracket Clamp Carriage Bolts (Qty. 2) Flange Nuts (Qty. 2)
Gigabit PoE (24V, 0.5A) with
Mounting Bracket
Power Cord
Package Contents
Installation Requirements
LTU PtMP AP, such as model LTU-Rocket
13 mm wrench
Surge protection should be used for all outdoor installations. We recommend that you use
two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and the other at the
entry point to the building. The ETH-SP-G2 will absorb power surges and safely discharge
them into the ground.
Note: For guidelines about grounding and lightning protection, follow your local
LTU-Pro Quick Start Guide
×
Click for
Table of Contents

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
electrical regulatory codes.
Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are
required for all wired Ethernet connections.
Hardware Overview

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
Reset Button
USB-C Port
5 GHz LED
To reset to factory defaults, press and hold the Reset button for more than 10 seconds
while the device is powered on.
Reserved for future use.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
GPS LED
UNMS LED
LAN LED
Power LED
PoE In [24V] Port
Blue The LED will light blue when the link is active.
Blue
The LED will light blue when the GPS signal strength is
sufficient. This requires a minimum of three satellite
connections.
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti® Network
Management System (UNMS™). See “UNMS
Management”.
Blue Ready for use, connected to UNMS.
Steady Blue with Occasional
Flashing
Ready for use, unable to connect to UNMS, check
connection to UNMS server.
Quickly Flashing Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
Blue
The LED will light steady blue when an active Ethernet
connection is made to the Ethernet port and flash when
there is activity.
Blue The LED will light blue when the device is connected to a
power source.
This 10/100/1000 Ethernet port is used to connect the power and should be connected to
the LAN and DHCP server. Default IP address: 192.168.1.20
Pole Mounting
1.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
2.
3.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
4.
5.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
6.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
7.
8.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
9.

LTU-Pro Quick Start Guide
http://dl-origin.ubnt.com/qsg/LTU-Pro/LTU-Pro_EN.html[05.02.2020 14:09:00]
10.
Connecting Power
WARNING: The switch port must comply with the power specifications listed in the
“Specifications”.