Ultrak HEG14 User manual

14-INCH CAMERA
ENCLOSURE
WITH OPTIONAL
SUNSHIELD,
HEATER AND
BLOWER KITS
AND MOUNTING
BRACKET
HEG Serie
s
INSTALLATION
INSTRUCTIONS
Worldwide Support Center
1301 Waters Ridge Drive Lewisville, TX 75057
[phone] [phone] FAX [phone]

ii
ISSUE 1 - November 1996
1996 BY ULTRAK
ALL RIGHTS RESERVED
PRINTED IN ITALY
ULTRAK
1301 WATERS RIDGE DRIVE
LEWISVILLE, TX 75057
[phone]
ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED
BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK.
THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL
RESPECTS. HOWEVER, ULTRAK CANNOT ASSUME RESPONSIBILITY FOR ANY
CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR
NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH
CHANGES.

iii
TABLE OF CONTENTS
Paragraph Title Page
SECTION 1. HEG CAMERA HOUSING SERIES INTRODUCTION
1.1 PURPOSE ....................................................................................1
1.2 FEATURES...................................................................................1
SECTION 2. HOUSING INSTALLATION INSTRUCTIONS
2.1 HEG14-BK BLOWER KIT INSTALLATION..................................2
2.2 HEG14-HK HEATER KIT INSTALLATION...................................4
2.3 HEG14-BK BLOWER KIT WITH HEG14-HK
HEATER KIT INSTALLATION ..................................................6
2.4 CAMERA MOUNTING FOR HEG SERIES HOUSINGS..............8
2.5 HEG14-SS SUNSHIELD INSTALLATION..................................10
2.6 UL-WB+BJ & UL-WBM WALL BRACKET MOUNTING.............11
SECTION 3. SPECIFICATIONS
3.1 HEG HOUSING SPECIFICATIONS ...........................................12
3.2 HEG14-BK BLOWER SPECIFICATIONS ..................................12
3.3 HEG14-HK HEATER SPECIFICATIONS ...................................13
3.4 HEG14-SS SUNSHIELD SPECIFICATIONS .............................13
3.5 UL-WB+BJ & UL-WBM WALL MOUNT SPECIFICATIONS ......13

1
SECTION 1
HEG CAMERA HOUSING SERIES INTRODUCTION
1.1 PURPOSE
The HEG14 camera housing series includes stylishly and
functionally designed enclosures for 1/3”, 1/2” and 2/3” cameras
with fixed focal length or large zoom lenses. This manual
describes how to assemble the housing and its optional
components, affix the camera, and mount the assembly to a
suitable surface.
1.2 FEATURES
The HEG14 camera housing series feature:
•Contemporary design
•Extruded aluminum body with die-cast end-cover plates
•Adjustable mounting track
•Removable body for easy servicing
•Durable neoprene end-gaskets
•Compression cable fittings
•Adjustable mounting track
•Removable body for easy servicing
•Optional heater kit, blower kit and snap-on sunshield
components
•Indoor/outdoor applications
•Epoxy powder coating for corrosion resistance
•Dustproof, IP65 weatherproofing
•Low Cost
•Preassembled models:
1. HEG14.......................... housing
2. HEG14-01..................... housing with sunshield
3. HEG14-02..................... housing with sunshield
and heater kit
4. HEG14-03..................... housing with sunshield,
heater kit and blower kit

2
SECTION 2
HOUSING INSTALLATION INSTRUCTIONS
2.1 HEG14-BK BLOWER KIT INSTALLATION (without heater)
This section contains comprehensive instructions for installing
the blower kit into the HEG14 and HEG14-01 camera housing. If
you are also installing the heater, please skip to page 6 for
comprehensive instructions. The blower kit is available in a
preassembled package with a housing, heater kit, and sunshield
under model HEG14-03.
1. If applicable, remove the sunshield by snapping it off the
main housing unit.
2. Remove the three Phillips panhead screws located on the
rear of the housing unit and loosen the set screws on either
side of the external mounting plate. Retain the screws and
their black rubber gaskets, which were left in the holes on the
rear of the housing. (See Figure 1)
3. By sliding the housing shell away from the rear portion of the
unit, separate the housing into two sections. It may be
necessary to unscrew the ground wire connection on the
silver camera mounting plate. However, be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 1)
4. Locate the following parts that are taped to or enclosed in the
housing: two black plastic plates, a nylon washer, and three
hexagonal screws of varying lengths for camera mounting;
two hexagonal screws with two metal washers; and two
Phillips panhead screws with nylon washers and rubber
gaskets. Set these parts aside for later use.
FIGURE 1

3
5. Remove the standard silver camera mounting plate by
unscrewing the two Phillips panhead screws located at the
rear. Retain the screws. (See Figure 1)
6. Remove the rear of the housing from the base by unscrewing
the two Phillips flathead screws. (See Figure 1)
7. Use these screws to replace the rear with the blower unit,
being careful not to damage the wiring to the attached circuit
board. (See Figure 2)
8. Reattach the standard silver camera mounting plate to the
shelf extending from the rear of the housing. Align the holes
and secure using the two panhead Phillips screws mentioned
in step 5. (See Figure 2)
9. Next, mount the blower circuit board on the camera mounting
plate. To do this, first place the two plastic spacers on the
two holes near the rear of the plate. Set the blower circuit
board on top of the spacers, aligning the holes and keeping
the wiring on the same side. Insert the small Phillips panhead
screws and secure the assembly. (See Figure 2)
10. Connect the
external power
supply (not
included) to the
circuit board. The
recommended
power supply is 24
VAC, 50 VA. (See
Figure 3)
FIGURE 2
FIGURE 3

4
11. To mount your camera, consult the section Camera
Mounting for HEG Series Housings on page 8. Begin with
step 5. Then see UL-WB+BJ & UL-WBM Wall Bracket
Mounting on page 11.
2.2 HEG14-HK HEATER KIT INSTALLATION (without blower)
This section contains instructions for installing the heater kit for
the HEG14 and HEG14-01 camera housings. If you are also
installing the blower unit, please skip to page 6 for
comprehensive instructions.
While this heater kit is sold as an add-on component for the
HEG14 and HEG14-01, it is also available in a preassembled
package. The HEG14-02 is a 14-inch camera housing with an
installed sunshield and heater. The HEG14-03 adds a blower kit
to the HEG14-02.
1. If applicable, remove the sunshield by snapping it off the
main housing unit.
2. Loosen the three Phillips panhead screws located on the rear
of the housing unit until they release the body of the housing.
Leave the screws intact in the rear portion of the housing.
Also loosen the set screws on either side of the external
mounting plate. (See Figure 4)
3. By sliding the housing shell away from the rear portion of the
unit, separate the housing into two sections. It may be
necessary to unscrew the ground wire connection on the
silver camera mounting plate. However, be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 4)
FIGURE 4

5
4. Locate the following parts that are taped to or enclosed in the
housing: two black plastic plates, a nylon washer, and three
hexagonal screws of varying lengths for camera mounting;
two hexagonal screws with two metal washers; and two
Phillips panhead screws with nylon washers and rubber
gaskets. Set these parts aside for later use.
5. Remove the standard silver mounting plate by unscrewing
the two Phillips panhead screws located at the rear. Then
replace this unit with the optional mounting plate with built-in
heater. Make sure that the heater plate is secured to the
shelf that extends from the rear of the housing unit. (See
Figures 4 & 5)
6. Connect the external
power supply (not
included) to the circuit
board. The
recommended power
supply is 24 VAC, 50 VA.
(See Figure 6)
7. To mount your camera,
consult the section
Camera Mounting for
HEG Series Housings on
page 8. Begin with step
5. Then see UL-WB+BJ
& UL-WBM Wall Bracket
Mounting on page 11.
FIGURE 5
FIGURE 6

6
2.3 HEG14-BK BLOWER KIT WITH HEG14-HK HEATER KIT
INSTALLATION
This section contains instructions for installing the heater kit and
blower kit for HEG14 and HEG14-01 camera housings. While
these kits are sold as add-on components, they are also
available in a preassembled package. The HEG14-03 and is a
14-inch camera housing with an installed sunshield, heater and
blower.
1. If applicable, remove the sunshield by snapping it off of the
main housing unit.
2. Remove the three Phillips panhead screws located on the
rear of the housing unit and loosen the set screws on either
side of the external mounting plate. Retain the screws and
their black rubber gaskets, which were left in the holes on the
rear of the housing. (See Figure 7)
3. By sliding the housing shell away from the rear portion of the
unit, separate the housing into two sections. It may be
necessary to unscrew the ground wire connection on the
silver camera mounting plate. However, be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 7)
4. Locate the following parts that are taped to or enclosed in the
housing: two black plastic plates, a nylon washer, and three
hexagonal screws of varying lengths for camera mounting;
two hexagonal screws with two metal washers; and two
Phillips panhead screws with nylon washers and rubber
gaskets. Set these parts aside for later use.
5. Remove the standard silver camera mounting plate by
unscrewing the two Phillips panhead screws located at the
rear. Retain the screws. (See Figure 7)
FIGURE 7

7
6. Remove the rear of the housing from the base by unscrewing
the two Phillips flathead screws. (See Figure 7)
7. Use these
screws to
replace the
rear with the
blower unit,
being careful
not to damage
the wiring to
the attached
circuit board.
(See Figure 8)
8. Attach the mounting plate with heater unit to the shelf
extending from the rear of the housing. Align the holes and
secure using the Phillips panhead screws mentioned in step
5. (See Figure 8)
9. Using a small screwdriver, disconnect the wiring to the N and
L1 ports on the heater circuit board. (See Figure 8)
10. Next, replace the heater circuit board with the circuit board
that is wired to the blower. To do this, locate the two Phillips
panhead screws on the heater circuit board. Unscrew them
and remove the board from the mounting plate. With the two
plastic spacers already over the small holes on the mounting
plate, set the blower circuit board on top of the spacers,
keeping the wiring on the same side. Align the holes in the
board with the spacers and insert the small Phillips panhead
screws. Secure the assembly. (See Figure 8)
11. Connect the heater
wiring harness to the
blower circuit board
as shown. Then
connect the external
power supply (not
included) to the
circuit board. The
recommended power
supply is 24 VAC, 50
VA. (See Figure 9)
12. To mount your camera, consult the next section, Camera
Mounting for HEG Series Housings page 8. Begin with step
5. Then see UL-WB+BJ & UL-WBM Wall Bracket Mounting
on page 11.
FIGURE 8
FIGURE 9