Unfinished Furniture of Wilmington SHEAFBACK C-1622 User manual

ITEM
NO.
:
C
-
1622
REVISED JUN 04, 2013
Printed in Vietnam
- 1 -
Description
Item No.
:
SHEAFBACK ARM CHAIR
: C-1622
ASSEMBLY INSTRUCTIONS

ITEM
NO.
:
C
-
1622
REVISED JUN 04, 2013
Printed in Vietnam
- 2 -
BEFORE ASSEM
B
LY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
PART
LIS
T
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Q
ty
Sketch
NO
Description
Q
ty
Sketch
A Back 1 B Seat frame 1
C Seat 1 D Front leg
(L-R) 2
E
Side
stretcher
(L-R)
2 F Center
stretcher 1
G Arm
(L-R) 2
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM
NO.
:
C
-
1622
REVISED JUN 04, 2013
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Q
ty
Sketch
NO
Description
Q
ty
Sketch
1
Short bolt
( M6x40mm)
5 2
Medium bolt
(M6x60mm)
4
3
Long bolt
(M6 x 80mm)
4 4
Wood Screw
(M4 x 35mm)
12
5
Lock Washer
(6.5 x11mm)
13 6
Flat Washer
(6.5 x19mm)
13
7
Allen Key
(4x80mm)
1
STEP 1
Attach seat frame (B) to the back (A) by using bolts (3) and (1), and washers (5) and (6). Tighten with
allen key (7) as shown below.
Note: DO NOT tighten any of the bolts, until the chair is assembled. Place the chair on a flat level
surface to make sure the chair is level, then tighten all of the bolts.

ITEM
NO.
:
C
-
1622
REVISED JUN 04, 2013
Printed in Vietnam
- 4 -
STEP 2
Attach front legs (D) to the seat frame with bolts (2), and washers (5) and (6). Tighten with Allen key
(7).
Place side stretchers (E) and center stretcher (F) between front and back legs. Attach stretchers with
the screws (4) as shown below. Tighten with a screwdriver.
STEP 3
Attach arms (G) to seat frame with bolts (1), and washers (5) and (6). Tighten with the allen key (7).
Then attach arms (G) to the back with screws (4). Tighten with a screwdriver.

ITEM
NO.
:
C
-
1622
REVISED JUN 04, 2013
Printed in Vietnam
- 5 -
STEP 4
Attach the seat (C) to top of the seat frame with screws (4) as shown below. Tighten with a
screwdriver.