Unfinished Furniture of Wilmington OT-202S User manual

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: COTTAGE SOFA TABLE
: OT-202S

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product with
rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Back panel
(Left)
1
C
Back panel
(Center)
1
D
Back panel
(Right)
1
E
Side panel
(L-R)
2
F
Bottom
frame
1
G
Bottom shelf
1
H
Leg
4

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Wooden knob
(35 x 35mm)
2
5
Flat washer
(6.5 x19mm)
22
METAL KNOB
(32 x 28mm)
GOES WITH FINISHED
ITEM ONLY.
2
6
Allen Key
(M4 x 30mm x 110mm)
1
2
Pan head screw
*Metal knob: (M4x22mm)
*Wooden knob:(M4x25mm)
2
7
Short screw
(M3 x 15mm)
4
3
Bolt
(M6 x 35mm)
22
8
Shelf support bracket
4
4
Spring washer
(6.5 x11mm)
22

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 5 -
Attach back panels (B), and (C) and (D) to the top (A) with bolts (3), and washers (4) and (5) as shown
below. Tighten with Allen key (6).
STEP 2
Attach side panels (E) to top (A) with bolts (3), and washers (4) and (5) as shown below. Tighten with
Allen key (6).
STEP 1

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 6 -
STEP 3
Attach bottom frame (F) to side panels (E) and back panels (B), and (C) and (D) with bolts (3), and
washers (4) and (5) as shown below. Tighten with Allen key (6).
STEP 3
STEP 4
Attach legs (H) to the unit by screwing them into bottom frame (F), as shown below.

ITEM NO.: OT-202S
ISSUED DEC 26, 2016
Printed in Vietnam
- 7 -
STEP 5
Attach brackets (8) to the unit as shown below. Place shelf (G) on the brackets and attach with screws (7).
Tighten with a screwdriver.
STEP 6
Attach knobs (1) to front of drawers with pan head screws (2), as shown below. Tighten with a screwdriver.