Unfinished Furniture of Wilmington TRENTON TV-10A User manual

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: TRENTON TV CENTER
: TV-10A AND TV-10B

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST TV-10A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Bottom
2
PART LIST TV-10B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
C
Vertical panel
(L-R)
2
D
Fixed shelf
1
E
Side panel
(L-R)
2
F
Apron
(L-R)
2
G
Side Back
panel
2
H
Back panel
2
I
Center Back
panel
1
J
H-connector
2

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
-10
PART LIST TV-10B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
K
Center Leg
2
L
Glass section
(407 x 373 x 3mm)
2
M
Door frame
2
N
Door
2
O
Drawer front
2
P
Drawer side
(L-R)
4
Q
Drawer bottom
2
R
Drawer back
2
S
Support bar
2
T
Side
Adjustable shelf
2
U
Center
Adjustable shelf
2

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
24
9
Bracket
16
2
Spring Washer
(6.5 x 11mm)
24
10
Long Pan head screw
*Metal knob: (M4x22mm)
*Wooden knob:(M4x25mm)
6
3
Large Flat Washer
(6.5 x 19mm)
16
11
Wooden Knob
(38 x 30mm)
6
4
Small Flat Washer
(6.5 x 13mm)
8
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
6
5
Long Screw
(M4 x 35mm)
28
12
Steel band
2
6
Short Pan head
screw
(M3.5 x 15mm)
12
13
Allen key
(M4 x 30mm x 110mm)
1
7
Short Screw
(M3.5 x 15mm)
44
14
Short Pan head screw
(M3 x 15mm)
8
8
Magnet
4
NOTE: HARDWARE IS PACKED IN CARTON TV-10B.

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 1
Attach vertical panels (C) to top (A) and shelf (D) with bolts (1), and washers (2) and (3) as shown
below. Tighten with Allen key (13).
STEP 2
Insert aprons (F) into vertical panels (C) and side panels (E), and then attach with screws (5) as shown below.
Attach side panels (E) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (13).
Attach magnets (8) to aprons (F) and shelf (D) with pan head screws (14) as shown below. Tighten
with a screwdriver.
1
2
3
13
8
14
5
A
C
C
D
E
E
F
1
2
3
13

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 7 -
STEP 3
Attach bottom (B) to side panels (E) with bolts (1), and washers (2) and (4) as shown below. Tighten
with Allen key (13).
Attach bottom (B) to vertical panels (C) with bolts (1), and washers (2) and (3) as shown below.
Tighten with Allen key (13).
STEP 4
Attach legs (K) to bottom (B) with bolts (1), and washers (2) and (4) as shown below. Tighten with Allen key (13).
Attach H-connector (J) to bottom (B) with screws (5) as shown below. Tighten with a screwdriver.
Slide back panels (G), and (H) and (I) into the grooves of vertical panels (C) and H-connector, and
then attach back panels to bottom (B) with screws (6) as shown below.
E
1
2
3
1
2
4
B
A
E
C
D
1
2
4
13
G
G
H
H
I
A
B
E
J
K
K
5
6

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 8 -
STEP 5
Attach doors (N) and (M) to side panels (E) and vertical panels (C) with screws (7) as shown below.
Tighten with a screwdriver.
Insert glass sections (L) into back of doors (M), and lock it as shown below.
STEP 6
Attach drawer sides (P) to drawer front (O) with screws (5) as shown below. Tighten with a screwdriver.
Insert drawer bottom (Q) into the grooves at bottom of drawer sides (P) and drawer front (O) as shown
below.
Attach drawer back (R) to drawer sides (P) with screws (5) as shown below. Tighten with a screwdriver.
Attach support bar (S) to bottom drawer (Q) with screws (5) as shown below. Tighten with a screwdriver.
L
7
A
M
N
B
M
N
O
P
P
Q
5
5
R
S
5
5
5
5

ITEM NO.: TV-10A AND TV-10B
REVISED NOV 01, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 9 -
STEP 7
Carefully put the drawers into the unit.
Insert brackets (9) into the unit as shown below. Place shelves (U) and (T) on the brackets and attach
with screws (7). Tighten with a screwdriver.
Attach knobs (11) to front of drawer with pan head screws (10) as shown below. Tighten with a screwdriver.
Attach steel bands (12) to the unit with short screws (7) and attach the steel band to the wall with long
screws (5) as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
T
T
U
U
12
7
5
5
9
7
11
10
N
N
M
A