UNICOR HIGHTECH 6700D User manual

6
5
4
1
32HOLE 타공
접지선
이 선을 꺽어 문 모서리에 맞춰주십시오.
접지선
이 선을 꺽어 문 모서리에 맞춰주십시오.
User manual
6700SK
6700DK
6700D
6700D
6700S
6700S
6700DK
6700SK
6700 Series
User manual
UNICOR HIGHTECH CO., LTD
www.unicor.co.kr
As this is a keyless digital door lock, damage may occur
to parts of the deadlock system if it is not used according
to the manual. Users should be fully aware of the manual
and how to operate this product.
Caution
Safety precautions
The precautionary measures are for the safety of the user,for the prevention of property
damage,and for the avoidance of any inconveniences due to an accident.These must be read
and followed properly.
• Do not disassemble or alter the lock.
• Do not install where the distance over
5mm between the door and door frame.
• Please do not expose the password and
change the password in regularly.
• Batteries should not be exposed directly to
heat sources or flames, or submerged in water,
because they may leak or explode, resulting in
severe damage.Please do not use damaged
batteries.
• Do not press using sharp tools or press
numeric button excessively.
• Make sure the door is completely locked when
going out.
• Place the batteries carefully and correctly according
to their polarity (+/-). If the batteries are inserted
in a wrong way, differently from the indicated
direction or polarity,leakage or rupture could occur.
Pay attention to it.
• Please do not mix old with new batteries or use
different types.
Always use new alkaline batteries.
• Do not clean the product with flammable materials
such as alcohol, benzene or thinners. Such materials
may damage the surface or cause a fire.
• Replace the current batteries with new ones within
1 week after the battery replacement notification
melody sounded off for the first time.
Warning
Model Door opening type Mechanical key
2way / Password & Digital key
2way / Password & Smart key
3way / Password & Digital key& Mechanical key cylinder
3way / Password & Smart key& Mechanical key cylinder
Components of each model
Components
Front ass’y Back ass’y Rubber pad for
the back ass’y
Digital touch key
Strike
Mortise
Handle shaft
Handle shaft stop ring
Battery 4pcs Installation template User manual
Front ass’y Back ass’y
Battery cover
Back handle
Panic release function with handle
The handle is a one-touch type product developed by the company. When it is installed successfully,
the user just needs to swing it down to open the door safely and conveniently when moving from
the inside area to the outside area.
Touch plate
Mortise
Registering and changingthe password
The door must be opened while registering the password.
Caution
1. Open the battery cover of the back ass’y, and
short press the [Reg.] button one time. 2.Check that the front keypad lamp is
turned on.
3. Enter the password of 3-20 digits.
Caution
If no password is entered within 14 seconds after the [Reg.] button is pressed, the registration
process will be cancelled.When a new password is registered (The above 1-4 steps), the
previous one will be automatically deleted. If the registration mode is cancelled, the previous
password will be maintained.
Registering (again) the digital touch key / smart tag (card)
Caution
When it is needed to register digital touch keys, smart tags (cards) and remote control, or
registering them again, it is required to register them all together at once. Remote control is
optinal. purchasing it separetly.
1. Open the battery cover of the back ass’y,
and short press the [Reg.] button one time. 2. Bring the digital touch keys into contact at the touch plate in order. (When each digital touch
key is comes in contact at the touch plate,
the registration will be completed while a sound is
generated for checking the registration)
※Bring the smart tag (card) into contact at the touch plate.
3. Press the [Reg.] button after registering
all digital touch keys or smart tags (cards). 4. Registering the remote control (option): Short press the [Reg.] button of the back ass’y
one time, and the press the [Open]
button for registration.
Attention
Caution
Deleting the digital touch key, smart tag(card),
and remote control
1.Open the battery cover of the back ass’y, and
short press the [Reg.] button one time.
2. Check that the front keypad lamp is turned on.
3. Press number [0] for 5 seconds. All the digital
touch keys, card keys and remote control will
be deleted while a sound will be generated
for checking.
For 5
seconds
Locking the door from the inside
▶When theauto lock function is set.
After 3
seconds
When the auto lock function is set, the door will be automatically locked 3 seconds
after the door is closed.
▶When theManual lock function is set.
Opening the door from the inside.
Caution
If the user does not open the door within 7 seconds after pulling the handle down,
the door will be automatically locked.
▶Pulling the back handle down
Pull the handle of the back ass’y down slightly. Then, the Panic release function will be activated,
disabling the locked state and opening the door.
Opening the door from the outside.
▶Opening the door by
using the password.
Touch the keypad.
Enter the Password and [*] button
needs to bring the handle down
to open the door.
▶Opening the door by using the digital touch key, smart
tag (card) or the remote control.
1. Bring the registered digital touch key or smart tag key into contact at the touch plate,
or press the [Open] button in case of the remote control.
2. When there is a sound for checking. Then, the user needs to bring the handle down
to open the door.
▶Opening the door by using
the mechanical key cylinder.
Insert the key into the key hole and turn
it to open the door.
Caution
The lifetime of the batteries is based on the result of the tests by the company and is not an absolute
measurement. It will vary depending on the temperature and humidity of the installed locations as well as
depending on the frequency of usage and the quality of batteries.
The functions, design, and composition of the product may change without prior notification for the purpose
of improving its quality.
-This manual may change without notice in case of product improvement.
-This manual may not be edited or changed without the manufacturer’s prior permission
- Product specifications are subject to change without prior notice.
Smart Key
UNICOR UNICOR
UNICOR
Mechanical key
cylinder
screws
Option
Video phone
interface,
remote control
UNICOR
Touch keypad
Touch plate,
Emergency key insertion
Front handle
Emergency
power supply
terminal
UN-6700D(2W) and
UN-6700DK(3W)
UN-6700DK(3W) and
UN-6700SK(3W)
Wireless
communication
receiver
Registration
button
Double locking
※
In addition to 2 or 4 pcs of smart tag that are
provided basically, 13.56Mhz ISO 14443A
type RF tags, NFC cards and credit cards can
be also registered as card key
UN-6700S(2W) and UN-6700SK(3W)
4.
Press the [Reg.] button. Then, the
registration will be completed while a
sound is generated for checking the
registration.
4.
* Deleting the remote control Press [Reg.]
and then press [1] for 5 seconds.
Press [Double locking] one time
Short press [Double locking] button one time.
then door will be closed.
When it is needed to register additional digital touch keys and smart tags (cards)
(totally 50pcs of keys can be registered), it is required to repeat the above process 2 before
the keypad lamp is turned off.
If neither the digital touch key nor the smart tag (card) is contacted or if the [Open] button is
not pressed, in case of the remote control,for 14 seconds after the [Reg.] button is pressed,
the registration process will be cancelled.When a new digital touch key,smart tag (card) or a
new remote control is registered (The above 1–4 steps),the previous one will be automatically
deleted.
Dead bolt
(locking section)
Latch bolt
This is fixed, the right-hand door mode is set to default, meaning that any additioanl
adjustment isn't needed for the right-hand users. If the door is a left-hand type, the latch bolt
should be adjusted. otherwise, the door will not be closed.
How to change the latch bolt
1.After removing the plate,
set the latch bolt to fit the
left/right hand door.
(Rotates the latch bolt 180
degree to switch the right
/ left hand.) 180 degree rotation
2. After mounting the
mortise on the door,
put the plate and tighten
the screws.
Mortise pin
* Must be used for
installation.
UN-6700D
UN-6700S
UN-6700DK
UN-6700SK

?
▶
▶
Volume control function
[Reg.]-[7]-[Reg.]
▶ Nomal (initial value)
▶ Mute ▶
High tone
[Reg.]-[8]-[Reg.] [Reg.]-[9]-[Reg.]
This function helps the users to adjust the volum level.
12
11
10
789
Locking the doorfrom the outside.
▶When the auto lock function is set.
When the door is closed, it will be automatically locked 3 seconds later.
Touch the keypad. Then, the door will be locked.
▶When the manuallock function is set.
Internal double lock function
▶Setting
While the door is locked, press the [Double locking] button of the back ass’y for
3 seconds. Then, a sound for checking will be generated, completing the setting.
For 3 seconds
▶Unsetting
Bring the handle down from the inside and open the door.
Opening the door by using the handle.
Releasingthe double lock function
from the outside
This makes it possible to unset the double lock function from the outside in case the double
lock function of the door should be set accidently.
▶ Releasing
1. While the door is locked, touch the keypad and enter the registered password.
2. Press the [#] button and press the password and press the [*] button again.
Forced lock function
▶Setting
For 5 seconds.
▶Releasing
This function will be automatically disabled when the user opens the door and enters the
premise normally by using the password, digital touch key or the smart tag (card).
▶How to use the
function
After entering 78945 Enter 1234
Information
Mute
function
This removes the sound temporarily (one time) when it is
needed to use the door lock quietly regardless of the currently
set operating sound.
Unauthorized entry / Damage alarm
While the door is closed, if an abnormal opening of the door
(For example: Someone breaks into the premise by opening
up the gap in the door) is detected, a warning sound of
80dB will be generated.
▶How to disable the warning sound
The warning is disabled.
Enter the password normally or bring the digital touch key or smart tag (card) into contact
normally. Then, the warning sound will be disabled.
The batteries are removed The password is entered The digital touch key or smart tag
(card) is brought into contact
Mischief-preventionwarning and stopping
of operation
When an unregistered password is entered 3 consecutive times or an unregistered digital touch
key or smart tag (card) comes in contact 3 consecutive times, a warning sound will be generated
and the system operation will be stopped for 30 seconds.
Entered 3 consecutive times?
Warning the jam of the deadbolt
While the door is opened or closed, if the deadbolt does not come out or is not
retrieved normally because of the jam of the deadbolt, and a warning sound
“Bibibibi” will be generated.
“Bibibibi”
If the warning sound continues or the deadbolt does not work normally, it is required
to adjust the position of the door lock, requiring the user to contact a shop that can
handle the installation or an expert in the door locks
Caution
When the batteries need to be replaced, a melody “Open the east, east, east gate~ Open the
south, south, south gate” will sound off when operating the product. The melody lets the user
know about the need for replacing batteries
If the melody sounds off when operating the system, it is required to immediately open the battery
cover of the back ass’y, and replace all the batteries (4pcs) with new genuine 1.5V LR6 AA alkaline
batteries that can be purchased at nearby stationary stores or convenience stores.
Must use general batteries, not rechargeable ones.
Take precautions in placing the batteries in the compartment in order to prevent leakage or rupture that
could occur when they are placed wrongly.
Must replace the old batteries all with new ones, not partially.Do not use new ones with
discharged ones together.
It is designed to operate with the rated voltage 6V. If low voltage (4.2±0.3V) is detected,
a melody will sound off.
After the replacement, if the door lock stops working in a short period of time or the batteries are
discharged, the batteries could be defective. It is required to contact the shop where the user purchased
batteries and get new ones as replacement ones.
Caution
External EmergencyPower Supply
When the batteries of the door lock are completely discharged, making it impossible to open the
door from the outside by using the password digital touch key, or the card key, this function will
help supply the emergency power by using a 9V battery from the outside.
1)
Purchase a 9V battery in a rectangular shape from nearby stationary
stores or convenience stores.
2) Bring the battery into contact at the 9V battery input terminal at the
bottom of the front ass’y, and the press the [*] button while maintaining
the contact. If the power is supplied normally, a sound “Bibi~” will be
generated and the keypad will be turned on.
3)
Enter the password and then press the [*] button, or bring the
registered digital touch key or smart tag (card) into contact. Then, the
door will be opened.
(not rechargeable)
It is OK to bring a 9V battery as an emergency power into contact regardless of the + and – polarities.
When it comes to a key type model, it is possible to enter by using an emergency key even in this situation.
That is why it is recommended to carry the emergency key usually or keep it in a safe place (in a car).
The emergency power can be supplied when keeping the 9V battery into contact at the input terminal
Replace all the discharged batteries right after supplying the emergency power.
Information
Product standards
Warranty
UNICOR HIGHTECH CO., LTD
62 EunCheong Street, Namdong-Gu,Incheon, Korea (zip. 21643)
http://www.unicor.co.kr
◎The warranty period for all of the company’s products is 1 year from the date of purchase indicated
on the warranty certificate.
◎Even during the warranty coverage, users need to pay (the cost for trip, technical support and parts)
for some services if they are in the category of chargeable services.
◎User generally submit the warranty certificate or other methods that contains the installation
information when needed to request a service.
◎If the warranty certificate is not available, users need to submit a receipt, a credit card receipt or
a cash receipt instead (Except for a simple receipt)
◎If it is impossible to show the purchase date, the warranty period will be applied by taking into
consideration the product’s manufactured date + expiration period (6 months)
Types of consumer damage
Not the case of failure
● ● ●
●
●
●
●
When needed to break the product
due to the loss of secret code.
●
When the door is sagging, or
installation is defective, requiring
the product to be reinstalled.
●
Request for checking the product
for possible problems while there
is no specific symptom of a failure.
●
Problems in operation occur after
the user installs the product directly.
A visit for repair is needed as
there are mistakes and mishan dling
by the user such as mistakes in
replacing batteries and unskill ful
use of the product.
Defective operation due to poorly
inserted batteries and use of defective
batteries.
Failure and breaking due to the
use of the product for other purposes.
Failure and breaking caused by
the user on purpose or from an
external impact.
Failure and damage due to natural
disasters such as fires, floods,and
damage from sea water.
Penetration by water,condensation
and injection of chemicals,requiring
the internal circuits to be replaced,
and causing failures.
Mistakes and mishandling by the user
Other reasons
The product
is used in
normal
conditions
Mistakes and
mishandling
by the user
Front ass’y
(Front body)
Back ass’y
(Main body)
Digital touch key
Smart tag (card)
Emergency key
Battery
Door Handing
74W X 295H X25D mm Rated voltage: DC 6V
Working temperature:
-20℃ to 65℃
Sensor working temperature
(High temperature): 65℃
74W X 295H X30D mm
4pcs (2way touch model) / Possible to register up to 50pcs.
2pcs (2way tag model) / Possible to register up to 50pcs.
2pcs (2way key / 3way card models)
1.5V AA LR6 alkaline battery x 4
LH / RH / LHR / RHR
Failure occurs within 1 month from date of purchase
Product replacement
Free-of-charge repair
Free-of-charge repair
Paid repair
Replacement after depreciation
based on a fixed rate.
Product replacement
Failure occurs within 1 year from date of purchase
Same failure occurs 4 times or more
The repair parts are not available at the main office
Not the case of failure Paid repair
Mistakes and mishandling by the user
Defective installation, and other reasons
Will run for about 12 months when
used 10 times a day (6–8 months
in case of card models)
* The lifetime of the batteries is based on the result of the tests by the company and is not an absolute measurement.
It will vary depending on the temperature and humidity of the installed locations as well as depending on the frequency
of usage and the quality of batteries.
* The functions, design, and composition of the product may change without prior notification for the purpose of
improving its quality.
* Details of mistakes and mishandling by the user
Content of compensation
Within the warranty period
After the warranty period
Remarks
This Ability not be able to open the door by password, digital key and smart key or remote
control from outside.
To be released the internal double locking,
press the [Double locking] button for 3 seconds.
It's not possible to open the door by password, digital key and smart key from outside while
the double locking is set.
1. Touch the keypad and press
[0], and press [#] for 5 seconds.
Entering trick numbers to prevent
exposure password
Even when another person is watching nearby, this fuction makes the user to enter an trick
numbers before entering the real password.
When the password is 1234 the user
just needs to enter the real password
1234 at the end, after the trick
munbers, 78945 is entered.
The total entering number of digits combining the trick munber and real password
should be 3~20 digits.
Setting the auto / manual lock function
For locking the door automatically(or manually)
Setting the auto lock function
Remove the battry cover, and press [Reg.] -[3]-[Reg.] button.
[Reg.] [Reg.]
[Reg.] [Reg.]
After opening the door, the magnet sensor is operating to recognize the auto locking status.
If the door will not be opened within 7 seconds after releasing locking mode at the indoor/
outdoor, it will be locked again.
Setting the manual lock function
Remove the battry cover, and press [Reg.] -[6]-[Reg.] button.
After opening the door, the magnet sensor is operating to recognize the manual locking status.
To lock the door, please keep touch the keypad over 2 seconds.
Touch the keypad, and press [#] button one time.
Then, enter the registered password and [*] button.
* this is a temporary fuction, meaning that the
operating sounds will be generated when the door
lock is used again.
High-temperature
warning system
Even when the digital door lock is locked, if the temperature
sensor detects a high temperature(65℃±10℃), it will
generate a powerful alarm and open the door automatically
at the same time.
warning
If the back ass'y is exposed to direct sunlight a long period of time, it could cause the
temperature sensor to be cativated and a warning sound to be generaged accordingly.
The door's locked stated will be disabled even when the door is in the double-locked
state from the inside.
Releasing the High-
temperature warning
system
Open the battery cover and remove the all
batteries and wait for a certain time for the
temperature to go down. Remove all the batteries
Releasing
warning
◎For products pruchased outside of Korea, please consult your local distiriboutor or reseller as warranty
policies vary from country to country.
This Function makes it possible for an emergency sound to be generated for the purpose of
enhancing security when the door is handed from the inside when the user has to be absent
from the premise for a period of time.
Master Code / Master Key
The administrator only function to manage the collective complex.
It can be deleted when moving-in.
Master code
[
Reg.
]-[ 8 ]-[
3
]-[
Reg.
]-[ ]-[
Reg.
]
]-[ ]-[
Reg.
]
Delete
[ Reg. ]-[ #
]-[
#
]-[
#
]-[
7
]-[
3
Registered Password or Master Code
Master Key
Registration
[
Reg.
]-[ 8 ]-[ 6 ]-[
Reg.
]-[ Key touch ]-[
Reg.
]
Delete
[ Reg. ]-[ # ]-[ # ]- [ # ] -[ 7 ] -[ 6 ] -[ Reg. ]-[ ]-[ Reg. ]
Registered Password or Master Code
Registration (* The door must be opened while registering)
Enter the master code of 3~20 digits
After 3
seconds