Uniden BCT-12 User manual

Introduction
Welcome
Congratulations on your purchase of the BCT-12 Highway
Information System & Pre-programmed Warning Scanner!
State-of-the-art engineering and advanced electronics provide you
with a pre-programmed information radio designed for easy
operation and dependability.
With the BCT-12 Scanning Radio, you can listen to hundreds of
highway patrol, local police, sheriff’s department, department of
transportation, and news media frequencies as well as NOAA
weather channels.
The frequencies in your BCT-12 have been uniquely selected on a
State-by-State basis to provide you with the highest level of
scanning quality. Plus, new built-in technology sounds an alarm
when a priority channel is detected!
Best of all, you don’t have to program any frequencies. Just set the
BCT-12 for your state, and the scanner will do the rest. Please
read this Operating Guide thoroughly before attempting to operate
the unit.
Features
•Priority Alert •Windshield Mountable
•Local Police Coverage •Instant Weather
•Highway Patrol Coverage •Built-in Speaker
•9-Level Strength Meter •DOT Coverage
•Weather Alert •News Media Coverage
•Highway Patrol Detection •Pre-programmed Scanner
Covers All 50 States Plus
Canada
Visit our Internet site at http://www.uniden.com.
1
G:...Bct12 pdf.vp
Wed Dec 03 11:27:55 1997
Color profile: Disabled
Composite Default screen

Terms and Definitions
Frequency Radio signals are sent as waves through the air. These
waves move up and down. A frequency is the number of
times in a certain time period, usually a second, that
these waves move all the way up and all the way down
and back to all the way up. For example: 123.450 kHz
means that the waves are moving all the way up and all
the way down and back all the way up again 123,450
times each second.
Mobile Extender Most Highway patrol vehicles on the road today are
equipped with a secondary radio system known as a
“mobile extender” or “vehicle repeater.” Whenever the
dispatcher transmits to any vehicle in the district, every
“mobile extender” in every car withing the district is
activated.
Priority Alert Using a constant PRIORITY check of specific
frequencies in each state, the BCT-12 recognizes and
alerts you to transmissions from “mobile extender”
radios as well as from car-to-car, aircraft-to-aircraft and
other special-purpose frequencies. You receive an
audible (beep tone) and visual (flash of warning light)
alert whenever you are within an approximate three mile
radius of many Highway Patrol/State Police units.
Scanning Scanning is the process by which your scanning radio
checks each frequency for the presence of a signal, and
when it finds a frequency with a signal, for example
someone talking on it, it stops, allowing you to listen to
the signal.
Weather Alert Lets your scanner function as a severe weather warning
radio. With Weather Alert turned on, when the NOAA
issues a severeweather warning radio. With Weather
Alert turned on, when the NOAA issues a severe
weather warning, the BCT-12 sounds an alert tone and
youl will hear the emergency weather broadcast.
2
Introduction
G:...Bct12 pdf.vp
Wed Dec 03 11:27:55 1997
Color profile: Disabled
Composite Default screen

Unpacking
Carefully remove all items from the box. If there is any visible
damage, do not operate the equipment. Notify your dealer or
shipping carrier immediately.
For information or instructions on any problem that you may have,
call the Uniden Customer Service Center at:
[phone] Monday through Friday,
8:00 a.m. to 5:00 p.m. Central.
3
Introduction
G:...Bct12 pdf.vp
Wed Dec 03 11:27:55 1997
Color profile: Disabled
Composite Default screen

Included with Your BCT-12 Scanner
If any of these items are missing, please contact your place of
purchase.
4
OFF
MUTE
MODE
ALERT
L/0
HOLD
STATE
The BCT-12 Highway
Information System Windshield Mounting Bracket and Hardware Visor Clip Mounting Bracket
BCT-12 Antenna Cigarette Adapter Power
Cord
BCT 12
SCANNER
Operating Guide
HOLD
L/0
STATE
MUTE
MODE
ALERT
HIGHWAY
SYSTEM
H
I
G
Y
W
ST
E
Y
OFF
BCT-12 Operating Guide
Window Mount Antenna
Νοω ισ τηε τιµε φορ αλλ γοοδ µεν το χοµε το τηε αιδ οφ τηε
παρτψ. Φουρ σχορε ψεασ αγο ουρ φατηερσ σετ φορτη α νεω
νατιον χονχειϖεδ ιν Λιβερτψ ανδ δεδιχατεδ το τηε
προποσιτιον τηατ αλλ µεν αρε χρεατεδ εθυαλ. Τηε θυιχκ
βροων φοξ ϕυµπεδ οϖερ τηε γαρδεν ωαλλ. Νοω ισ τηε τιµε
φο4ρ αλλ γοοδ µεν το χοµε το τηε αιδ οφ τηε παρτψ.
Νοω ισ τηε τιµε φορ αλλ γοοδ µεν το χοµε το τηε αιδ
οφ τηε παρτψ. Φουρ σχορε ψεασ αγο ουρ φατηερσ
σετ φορτη α νεω νατιον χονχειϖεδ ιν Λιβερτψ ανδ
δεδιχατεδ το τηε προποσιτιον τηατ αλλ µεν αρε
χρεατεδ εθυαλ. Τηε θυιχκ βροων φοξ ϕυµπεδ οϖερ
τηε γαρδεν ωαλλ. Νοω ισ τηε τιµε φο4ρ αλλ γοοδ µεν
το χοµε το τηε αιδ οφ τηε παρτψ.
Νοω ισ τηε τιµε φορ αλλ γοοδ µεν το χοµε το
τηε αιδ οφ τηε παρτψ. Φουρ σχορε ψεασ αγο
ουρ φατηερσ σετ φορτη α νεω νατιον
χονχειϖεδ ιν Λιβερτψ ανδ δεδιχατεδ το τηε
προποσιτιον τηατ αλλ µεν αρε χρεατεδ εθυαλ.
Τηε θυιχκ βροων φοξ ϕυµπεδ οϖερ τηε γαρδεν
ωαλλ. Νοω ισ τηε τιµε φο4ρ αλλ γοοδ µεν το
χοµε το τηε αιδ οφ τηε παρτψ.
Other Printed Material Straight Power Cord
G:...Bct12 pdf.vp
Wed Dec 03 11:28:02 1997
Color profile: Disabled
Composite Default screen

Installation
The BCT-12 uses a highly sensitive antenna to receive radio
signals. Its sensitivity and range depend on the method of
installation and the direction of the antenna in relation to the signal
source. Before you decide where to put your scanner, please keep
in mind one important factor:
For safety, do not mount the BCT-12 in a location where it will
obstruct your driving vision.
Helpful Tips
The antenna is located on the side of the unit. It should not be
obstructed and should be pointed as close to straight up or down
for best operation.
•Do not mount the unit in front of the heater or defroster vents.
•Do not leave the unit in direct sunlight or in the glove
compartment of a closed car for long periods of time. Also,
removing the unit from the windshield makes you less
susceptible to break-in and theft.
•Be sure the BCT-12 is mounted free of obstructions from the
rear view mirror, sun visors, or the ceiling of the automobile.
Optional Antennas
Your BCT-12 was designed for the easiest installation possible.
Uniden has packaged an additional Window Mount antenna with
your BCT-12 that will provide better performance on VHF
frequencies. For the best reception possible in every state, you
might consider a mobile scanner antenna which mounts
magnetically to your car or truck.
For more information on these and other options available for your
BearTracker, please ask your local Uniden dealer or call
1-800-248-5441.
5
G:...Bct12 pdf.vp
Wed Dec 03 11:28:02 1997
Color profile: Disabled
Composite Default screen

Installing the Antenna
BCT-12 Antenna
1. Pinch the sides of the
antenna and attach it to the
BCT-12.
Window Mount Antenna
1. Mount the antenna on the
inside of the windshield at
the far right-hand
(passenger) side.
Caution: Be sure the antenna does not obstruct the driver’s vision
in any way.
2. Route the antenna cable so it is out of the way and does not
obscure your view.
6
Installation
SYSTEM
HIGHWAY
A
L
E
R
T
M U T
E
M
O
D
E
H
OL
D
ST
A T E
L/
O
G:...Bct12 pdf.vp
Wed Dec 03 11:28:04 1997
Color profile: Disabled
Composite Default screen

Caution: Be sure the cable is out of the way of anyone getting in
or out of the car.
3. Plug the cable’s BNC
connector into the BCT-12.
Mounting the BCT-12
Visor Mounting
1. Snap the visor clip onto the
BCT-12.
Note: Make sure that the bracket tabs fit securely in the slots.
7
Installation
SYSTEM
HIGHWAY
A
L
E
R
T
M U T
E
M
O
D
E
H
OL
D
ST
A T E
L/
O
SQUELCH
Slots
G:...Bct12 pdf.vp
Wed Dec 03 11:28:07 1997
Color profile: Disabled
Composite Default screen

2. Slide the clip over the front of
the visor.
3. Adjust the angle of the
antenna as close to straight
up or down as possible.
Note: You can remove and replace the BCT-12 by sliding both
the unit and the visor mount off and on the visor.
8
Installation
SQUELCH
SQUELCH
G:...Bct12 pdf.vp
Wed Dec 03 11:28:09 1997
Color profile: Disabled
Composite Default screen

Windshield Mounting
1. Find a good position for the BCT-12 on your windshield. Refer
to the Helpful Tips on page 5 for some guidelines on mounting
positions.
2. Put the metal
mounting
bracket with
the suction
cups on the
windshield to
adjust it for
best position.
3. If necessary, adjust the metal
mounting bracket so that
when you slide the BCT-12
onto it, it is parallel to the
road surface and fits flush
against the windshield. Your
BCT-12 should look like one
of the examples at the right
once it is installed.
Caution: Do Not adjust the metal mounting bracket with the
BCT-12 attached. Doing so can cause damage to the
bracket and the unit.
9
Installation
1
2
34
1. Windshield
2. Road Surface
3. Metal Mounting
Bracket
4. Metal Mounting
Bracket parallel
to road
VOLUME
OFF
VOLUME
OFF
VOLUME
OFF
G:...Bct12 pdf.vp
Wed Dec 03 11:28:11 1997
Color profile: Disabled
Composite Default screen

4. Snap the windshield
mounting clip onto the
BCT-12.
5. Slide the plastic windshield
mounting clip into the metal
mounting bracket.
The mounting clip locks into the plastic portion at three different
positions. These positions can be used for vehicles with different
vertical angles of their windshields. The back position can be used
for vehicles with windshields that are slanted back.
10
Installation
Slots
VOLUME
OFF
SYSTEM
HIGHWAY
A
L
E
R
T
M U T
E
M
O
D
E
H
OL
D
ST
A T E
L/
O
G:...Bct12 pdf.vp
Wed Dec 03 11:28:13 1997
Color profile: Disabled
Composite Default screen

6. Place the bracket and the
BCT-12 in the proper location
on the windshield of your
vehicle and press the suction
cups firmly against the
windshield. If the BCT-12
does not fit flush against the
windshield, try a different
position on the metal
mounting bracket.
7. Adjust the angle of the
antenna as close to straight
up or down as possible.
11
Installation
VOLUME
OFF
VOLUME
OFF
VOLUME
OFF
SQUELCH
G:...Bct12 pdf.vp
Wed Dec 03 11:28:15 1997
Color profile: Disabled
Composite Default screen

Connecting the Power
Direct Connection
WARNING:The BCT-12 is designed to operate only with 12V DC,
negative ground power systems. Operation of the unit
on other voltages or polarities will cause damage to
the unit and may create a fire hazard.
The straight power cord provided with the unit has bare wires at
one end and a small connector at the other end.
1. Connect the positive wire to a 12V DC source in your vehicle’s
fuse box.
2. Connect the other wire to ground.
12
OFF
Fuse
Box
MUTE
MODE
ALERT
L/0
HOLD
STATE
G:...Bct12 pdf.vp
Wed Dec 03 11:28:17 1997
Color profile: Disabled
Composite Default screen

3. Run the power cord from the fuse box to the BCT-12.
Note: Ensure the cord does not interfere with vehicle
operation or cause a tripping hazard.
4. Plug the power cord connector into the BCT-12 at the jack
labeled “DC 12V.”
Note: Push the connector firmly into the jack.
Using the Cigarette Lighter Adapter
1. Insert the small connector
into the jack on the side of
the unit.
2. Insert the other end into the
cigarette lighter socket of
your vehicle.
13
Connecting the Power
MUTE
MODEMODE
ALERT
L/0
HOLD
STATE
OFF
G:...Bct12 pdf.vp
Wed Dec 03 11:28:18 1997
Color profile: Disabled
Composite Default screen

When installing the power cord, make sure that:
•The socket is clean to allow proper contact.
•The power cord does not block the antenna area of the unit.
Your unit also comes with 10 power cord mounting clips. You can
use these clips to attach the power cord to the window frame or
other parts of the vehicle, keeping it neat and out of the way. Use
the double-sided foam tape squares to attach each clip. Slip the
power cord into the clip to hold it securely in place.
Replacing the Fuse
The cigarette lighter plug contains a 1-ampere fuse to protect it
from power surges.
1. To replace the fuse, unscrew the top of the plug.
2. Remove the fuse and replace it with the same type.
3. To replace the top, push in
the two metal contacts and
twist into place.
14
Connecting the Power
G:...Bct12 pdf.vp
Wed Dec 03 11:28:20 1997
Color profile: Disabled
Composite Default screen

Operating Instructions
Applying Power
1. Turn the OFF/VOLUME
control counterclockwise to
power on the scanner. Adjust
the volume about 1/4 turn.
2. During power-on, a self-test is performed. Check the front
control panel for proper operation.
3. All the LED’s on the front
control panel light up and the
numbers 1 through 9 count
up on the LED display.An
Alert tone is also sounded.
This tells you that the
scanner is working properly.
4. The currently selected state
appears on the display.The
BCT-12 always comes on
with the last settings selected
and in the last mode of
operation.
15
MUTE
HOLD
ALT HP
LPW/A
09
MUTE
HOLD
ALT HP
LPW/A
TX
G:...Bct12 pdf.vp
Wed Dec 03 11:28:23 1997
Color profile: Disabled
Composite Default screen

Adjusting the Squelch
Think of the Squelch Control as a gate.
1. Turn the SQUELCH control fully counterclockwise. This raises
the “Squelch Gate” so high that no signals can get through.
2. Turn the SQUELCH control fully clockwise until you hear a
hiss. This lowers the “Squelch Gate” so that everything gets
through ... noise, weak signals, and strong signals.
3. Turn the SQUELCH control back counter clockwise just until
the hiss stops. Now the “Squelch Gate” allows only strong
signals through.
16
Operating Instructions
G:...Bct12 pdf.vp
Wed Dec 03 11:28:26 1997
Color profile: Disabled
Composite Default screen

4. Sometimes when you open the Squelch, you may trigger the
Alert feature even though no highway patrol cars are in the
area. If this happens, turn the SQUELCH control
counterclockwise until the “rushing” noise stops. Then turn the
BCT-12 off, and back on, to reset the Alert feature.
Note: In metropolitan areas, you may want to adjust the
Squelch control more counterclockwise to reduce the
range of the Alert feature. When set fully
counterclockwise, Squelch limits the Alert range to a
short distance.
17
Operating Instructions
G:...Bct12 pdf.vp
Wed Dec 03 11:28:26 1997
Color profile: Disabled
Composite Default screen

Selecting the State
See the foldout inside the front cover or your Quick Reference
Guide for key positions.
1. Select the state you are operating in by pressing the Skey
repeatedly. If you press and hold the Skey for 2 seconds,
the selector moves rapidly through all the states and Canadian
provinces.
2. The state code appears on
the display.See the following
page for a list of state codes
and Canadian provinces.
Note: The state codes are in alphabetical order by
abbreviation, followed by the Canadian province codes.
18
Operating Instructions
MUTE
HOLD
ALT HP
LPW/A
TX
G:...Bct12 pdf.vp
Wed Dec 03 11:28:27 1997
Color profile: Disabled
Composite Default screen

State and Canadian Province Codes
Code State Code State
AK Alaska NM New Mexico
AL Alabama NV Nevada
AR Arkansas NY New York
AZ Arizona OH Ohio
CA California OK Oklahoma
CO Colorado OR Oregon
CT Connecticut PA Pennsylvania
DC District of Columbia RI Rhode Island
DE Delaware SC South Carolina
FL Florida SD South Dakota
GA Georgia TN Tennessee
HI Hawaii TX Texas
IA Iowa UT Utah
ID Idaho VA Virginia
IL Illinois VT Vermont
IN Indiana WA Washington
KS Kansas WI Wisconsin
KY Kentucky WV West Virginia
LA Louisiana WY Wyoming
MA Massachusetts AB Alberta
MD Maryland BC British Columbia
ME Maine MB Manitoba
MI Michigan NB New Brunswick
MN Minnesota NF Newfoundland
MO Missouri NS Nova Scotia
MS Mississippi NT Northwest Territories
MT Montana ON Ontario
NC North Carolina PE Prince Edward Island
ND North Dakota PQ Quebec
NE Nebraska SK Saskatchewan
NH New Hampshire YT Yukon Territories
NJ New Jersey XX All Frequencies
19
Operating Instructions
G:...Bct12 pdf.vp
Wed Dec 03 11:28:28 1997
Color profile: Disabled
Composite Default screen

Selecting the Frequencies to Scan
Once you have selected the State or Canadian province, you are
ready to select the frequencies you want to scan.
Scanning Highway Patrol Frequencies
This mode scans State Police/Highway Patrol frequencies by
state. Mobile extender and other enforcement channels are priority
checked for activity.
Note: The priority check can be turned off by pressing and
holding the Alert key for 1.5 seconds.
1. To scan highway patrol
frequencies exclusively,
press the Mkey repeatedly
until HP is blinking in the LED
display.
2. The HP LED lights up.
3. While scanning, the BCT-12
displays the state code for
the state you selected. When
the BCT-12 detects an active
frequency, it displays HP in
the LED display and stops for
two seconds before it
resumes scanning.
20
Operating Instructions
MUTE
HOLD
ALT HP
LPW/A
HP
MUTE
HOLD
ALT HP
LPW/A
HP
MUTE
HOLD
ALT HP
LPW/A
MUTE
HOLD
ALT HP
LPW/A
HP
TX
G:...Bct12 pdf.vp
Wed Dec 03 11:28:33 1997
Color profile: Disabled
Composite Default screen