UNILITE PROSAFE ATEX-H2 User manual

ATEX-
H2
Specication
180 lumen white CREE LED
Durable impact resistant construction
90° rotational head
Rubberised head-band strap
Rubber housing
1 m submersible to IP67
Zone 0 hazardous location approved
Safety battery lock compartment
Polycarbonate lens
Smooth reector
Push-button micro-switch operation
Run time: high 3 hrs, low 4 hrs
Weight: 143 g (without batteries)
Size: 80 x 50 x 45 mm
Water resistant to IP67
Battery type: 3 x AAA batteries (not included)
Operation: Main Button HIGH – LOW – OFF
To replace the batteries, use the hex key to unlock the battery compartment on the back
of the head torch. Ensure that only batteries of the type specied in the instructions are used.
Replace batteries and ensure that the battery compartment is closed tightly.
Unilite cannot be held responsible for the use of mixed or incorrect batteries in our ATEX products.
Spezikation
CREE-LED weiß, 180 Lumen
Widerstandsfähige, stoßbeständige Konstruktion
90° Drehkopf
Gummiertes Kopf-Stirnband
Kunststoffgehäuse
Tauchfähigkeit 1 m gemäß IP67
Zugelassen für Gefahrenzonen der Zone 0
Batteriefach mit Sicherheitsverriegelung
Glas aus Polykarbonat
Glatter Reektor
Drucktaste Mikroschalter-Betrieb
Laufzeit: bei hoher Leistung 3 Stunde,
bei niedriger Leistung 4 Stunden
Gewicht: 143 g (ohne Batterien)
Größe: 80 x 50 x 45 mm
Wasserbeständig gemäß IP67
Batterietyp: 3 x AAA Batterien (nicht im Lieferumfang enthalten)
Betrieb: Hauptschalter HOCH – NIEDRIG - AUS
Um die Batterien auszuwechseln, verwenden Sie den Innensechskantschlüssel, um das
Batteriefach auf der Rückseite der Stirnlampe zu öffnen. Stellen Sie sicher, dass nur der in der
Anleitung angegebene Batterietyp verwendet wird. Tauschen Sie die Batterien aus und stellen
Sie sicher, dass das Batteriefach fest verschlossen wird.
Unilite übernimmt keine Haftung, falls in unseren ATEX-Produkten falsche oder gemischte
Batterien verwendet werden.
Caractéristiques techniques
DEL CREE blanche 180 lumens
Conception solide, résistante aux impacts
Tête pivotante à 90°
Sangle frontale caoutchoutée
Corps en caoutchouc
Submersible à 1 m selon IP67
Approuvée pour les zones de niveau de danger 0
Compartiment des piles verrouillé et sécurisé
Lentille en polycarbonate
Réecteur lisse
Fonctionnement du micro-interrupteur par bouton-poussoir
Durée de fonctionnement: 3h à forte puissance,
4h à faible puissance
Poids: 143 g (avec les piles)
Taille: 80 x 50 x 45 mm
Etanche selon IP67
Type de piles: 3 piles AAA (non fournies)
Fonctionnement: Bouton principal FORTE PUISSANCE– FAIBLE PUISSANCE – ARRET
Pour remplacer les piles, utilisez la clé hexagonale pour déverrouiller le logement des
piles à l’arrière de la lampe frontale. Assurez-vous de n’utiliser que le type de pile indiqué
dans les instructions. Remplacez les piles et assurez-vous que le logement des piles est
bien fermé.
Unilite décline toute responsabilité en cas d’utilisation de piles incorrectes dans nos produits ATEX.
Speciche
LED CREE bianco 180 lumen
Struttura durevole resistente agli impatti
Testina girevole con rotazione a 90°
Fascia frontale gommata
Guscio gommato
Sommergibile no a 1 m, grado IP67
Omologato per uso in ambienti pericolosi Zona 0
Vano batterie con chiusura di sicurezza
Lente in policarbonato
Riettore levigato
Funzionamento tramite microinterruttore a pressione
Durata di funzionamento: forte 3 ora, debole 4 ore
Peso: 143 g (senza batterie)
Dimensioni: 80 x 50 x 45 mm
Grado di resistenza all’acqua IP67
Tipo di batteria: 3 batterie AAA (non incluse)
Funzionamento: Pulsante principale FORTE – DEBOLE – SPEGNIMENTO
Per sostituire le batterie, utilizzare la chiave a brugola per aprire il vano batterie posto
sul retro della torcia frontale. Utilizzare solo il tipo di batterie specicato nelle istruzioni.
Sostituire le batterie e chiudere saldamente il vano batterie.
Unilite non può essere ritenuta responsabile qualora si usino batterie sbagliate o mischiate
nei propri prodotti ATEX.
Especicaciones
LED CREE blanco 180 lúmenes
Estructura duradera resistente a los impactos
Cabezal orientable con rotación de 90°
Correa de sujeción frontal engomada
Armazón de goma
Sumergible hasta 1 m, código IP67
Aprobado para entornos peligrosos de Zona 0
Compartimiento para batería con cierre de seguridad
Lente de policarbonato
Reector liso
Funcionamiento mediante microinterruptor de tipo pulsador
Tiempo de funcionamiento: fuerte 3 hora, débil 4 horas
Peso: 143 g (sin baterías)
Medidas: 80 x 50 x 45 mm
Código de resistencia al agua IP67
Tipo de batería: 3 baterías AAA (no incluidas)
Funcionamiento: Botón principal FUERTE – DÉBIL – APAGADO
Para sustituir las baterías emplee la llave Allen para abrir el compartimiento de baterías
situado en la parte trasera de la linterna frontal. Emplee únicamente el tipo de baterías
especicado en las instrucciones. Sustituya las baterías y cierre bien el compartimiento de
baterías.
Unilite no podrá ser considerada responsable si se emplean baterías incorrectas o mixtas en sus
productos ATEX.
Unit 6, Colemeadow Road, North Moons Moat, Redditch, Worcestershire, UK, B98 9PB
T■00[44] 1527 584 344 F■00[44] 1527 584 345 E■[email protected].uk www.unilite.co.uk

ATEX-
H2
Unit 6, Colemeadow Road, North Moons Moat, Redditch, Worcestershire, UK, B98 9PB
T■00[44] 1527 584 344 F■00[44] 1527 584 345 E■[email protected].uk www.unilite.co.uk
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
ENGLISH ISSUED: 2014.11.04 V1
Description:
ATEX-H2 Is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Warranty:
1 years Limited Warranty
Installation:
Operation:
Push the top button to operate. The sequence is high and then
low.
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92,
Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition
5. EN 60079-26 : 2007 Edition
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second
Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning: To reduce the risk of explosion do not mix new
batteries with used batteries, or mix batteries from
different manufacturers or from different types.
Warning: Remove the batteries when unused for a period of
time to prevent battery leakage in the device.
Safety Warnings:
1. The screw shall be secured tightly after opening and closing
of the enclosure.
2. Substitution of components may impair intrinsic safety.
3. Clean the headlamp only with damp cloth to avoid static
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE
2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
NON DANGEREUX.
Features:
»Intrinsically safe for use in
hazardous locations
»High and Low mode
functions
»Users high power CREE LED
»Focus and flood reflector
»Submersible in water
»Tough and durable casing
»Screw fastener for safety
precautions
»Build-in gas release vent
mode.
DAY SUN TECHNOLOGY LTD.
Address: 1st FL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Tel: [phone] / Email: [e-mail]
User Manual
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
English ISSUED: 2014.11.04 V1
Description: Installation:
DS-14 is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Features:
- Intrinsically safe for use in hazardous locations
- High and Low mode functions
- Users high power CREE LED
- Focus and flood reflector
- Submersible in water
- Tough and durable casing
- Screw fastenerfor safety precautions Operation:
- Build-in gas release vent Push the top button to operate. The sequence is high and then low.
mode.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92, Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition Warranty:
5. EN 60079-26 : 2007 Edition 1 years Limited Warranty
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning : To reduce the risk of explosion do not mix new batteries
with used batteries, or mix batteries from different
manufacturers or from different types.
Warning : Remove the batteries when unused for a period of time
to prevent battery leakage in the device. SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
Safety Warnings: PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE.
1. The screw shall be secured tightly after opening and closing of 2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
the enclosure. D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
2. Substitution of components may impair intrinsic safety. BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
3. Clean the headlamp only with damp cloth to avoid static NON DANGEREUX.
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
ATEX-H2
DAY SUN TECHNOLOGY LTD.
Address: 1st FL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Tel: [phone] / Email: [e-mail]
User Manual
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
English ISSUED: 2014.11.04 V1
Description: Installation:
DS-14 is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Features:
- Intrinsically safe for use in hazardous locations
- High and Low mode functions
- Users high power CREE LED
- Focus and flood reflector
- Submersible in water
- Tough and durable casing
- Screw fastenerfor safety precautions Operation:
- Build-in gas release vent Push the top button to operate. The sequence is high and then low.
mode.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92, Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition Warranty:
5. EN 60079-26 : 2007 Edition 1 years Limited Warranty
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning : To reduce the risk of explosion do not mix new batteries
with used batteries, or mix batteries from different
manufacturers or from different types.
Warning : Remove the batteries when unused for a period of time
to prevent battery leakage in the device. SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
Safety Warnings: PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE.
1. The screw shall be secured tightly after opening and closing of 2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
the enclosure. D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
2. Substitution of components may impair intrinsic safety. BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
3. Clean the headlamp only with damp cloth to avoid static NON DANGEREUX.
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
ATEX-H2
DAY SUN TECHNOLOGY LTD.
Address: 1st FL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Tel: [phone] / Email: [e-mail]
User Manual
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
English ISSUED: 2014.11.04 V1
Description: Installation:
DS-14 is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Features:
- Intrinsically safe for use in hazardous locations
- High and Low mode functions
- Users high power CREE LED
- Focus and flood reflector
- Submersible in water
- Tough and durable casing
- Screw fastenerfor safety precautions Operation:
- Build-in gas release vent Push the top button to operate. The sequence is high and then low.
mode.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92, Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition Warranty:
5. EN 60079-26 : 2007 Edition 1 years Limited Warranty
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning : To reduce the risk of explosion do not mix new batteries
with used batteries, or mix batteries from different
manufacturers or from different types.
Warning : Remove the batteries when unused for a period of time
to prevent battery leakage in the device. SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
Safety Warnings: PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE.
1. The screw shall be secured tightly after opening and closing of 2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
the enclosure. D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
2. Substitution of components may impair intrinsic safety. BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
3. Clean the headlamp only with damp cloth to avoid static NON DANGEREUX.
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
ATEX-H2
DAY SUN TECHNOLOGY LTD.
Address: 1st FL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Tel: [phone] / Email: [e-mail]
User Manual
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
English ISSUED: 2014.11.04 V1
Description: Installation:
DS-14 is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Features:
- Intrinsically safe for use in hazardous locations
- High and Low mode functions
- Users high power CREE LED
- Focus and flood reflector
- Submersible in water
- Tough and durable casing
- Screw fastenerfor safety precautions Operation:
- Build-in gas release vent Push the top button to operate. The sequence is high and then low.
mode.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92, Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition Warranty:
5. EN 60079-26 : 2007 Edition 1 years Limited Warranty
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning : To reduce the risk of explosion do not mix new batteries
with used batteries, or mix batteries from different
manufacturers or from different types.
Warning : Remove the batteries when unused for a period of time
to prevent battery leakage in the device. SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
Safety Warnings: PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE.
1. The screw shall be secured tightly after opening and closing of 2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
the enclosure. D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
2. Substitution of components may impair intrinsic safety. BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
3. Clean the headlamp only with damp cloth to avoid static NON DANGEREUX.
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
ATEX-H2
DAY SUN TECHNOLOGY LTD.
Address: 1st FL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Tel: [phone] / Email: [e-mail]
User Manual
HEADLAMP FOR USE IN HAZARDOUS LOCATIONS
English ISSUED: 2014.11.04 V1
Description: Installation:
DS-14 is a high power LED headlamp for use in hazardous locations
and is powered with three size AAA alkaline. It has high and
low mode operating functions that allows users to operate for high
brightness or long duration lighting.
Features:
- Intrinsically safe for use in hazardous locations
- High and Low mode functions
- Users high power CREE LED
- Focus and flood reflector
- Submersible in water
- Tough and durable casing
- Screw fastenerfor safety precautions Operation:
- Build-in gas release vent Push the top button to operate. The sequence is high and then low.
mode.
Certifications:
Class I Div 1&2 Grp ABCD / Class II Div 1&2 Grp EFG
Class III / Temperature Code T4 IP67
File number: E324236
II 1G Ex ia IIC T4 IP67
DEMKO 14 ATEX 1354X
Ex ia IIC T4 Ga IP67
IECEx UL 14.0059X
0539
Standards:
1. UL 913, Seventh Edition
2. CSA C22.2 No.157-92, Reaffirmed 2012
3. EN 60079-0 : 2009 Edition
4. EN 60079-11 : 2012 Edition Warranty:
5. EN 60079-26 : 2007 Edition 1 years Limited Warranty
6. IEC 60079-0 : Fifth Edition
7. IEC 60079-11 : Sixth Edition
8. IEC 60079-26 : Second Edition
Battery Replacement:
Use only battery types below:
Alkaline type
Energizer E92
Duracell MN2400
Panasonic AAA LR03(T)
Warning: Do not change batteries in hazardous locations.
Warning : To reduce the risk of explosion do not mix new batteries
with used batteries, or mix batteries from different
manufacturers or from different types.
Warning : Remove the batteries when unused for a period of time
to prevent battery leakage in the device. SÉCURITÉ INTRINSÉQUE:
1. AVERTISSEMENT : LA SUBSTITUTION DE COMPOSANTS
Safety Warnings: PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUE.
1. The screw shall be secured tightly after opening and closing of 2. AVERTISSEMENT : AFIN DE PRÉVENIR L’INFLAMMATION
the enclosure. D’ATMOSPHÉRES DANGEREUSES, NE CHANGER LES
2. Substitution of components may impair intrinsic safety. BATTERIES QUE DANS DES EMPLACEMENTS DÉSIGNÉS
3. Clean the headlamp only with damp cloth to avoid static NON DANGEREUX.
electricity.
4. Do not flash the light beam directly to human’s eyes.
5. Always use the device following the regulations of each
country.
ATEX-H2