Unipro UniTire V2 User manual

UniTire V2 Pressure Gauge
User Guide

II
PLEASE READ THE SAFETY
INSTRUCTIONS CAREFULLY
• Read the instructions.
• Keep these instructions.
• Follow all instructions.
• Do not use the UniTire in water.
• Be careful not to drop it on the ground.
• Do not leave it under heavy objects.
• Be careful not to cut the cable with
sharp objects.
• Clean only with a dry cloth.
• Refer all servicing to approved service
personnel.
WARNING
TO REDUCE THE RISK OF DAMAGE,
DO NOT EXPOSE THE UNITIRE TO RAIN OR
MOISTURE.
Important safety instructionsSafety

III
IMPORTANT SAFETY INSTRUCTIONS II
CONTENTS III
COPYRIGHT AND ACKNOWLEDGEMENTS IV
SALES AND SERVICE IN DENMARK IV
INTERNATIONAL DEALERS IV
DESIGN AND PRODUCTION IV
ABOUT THIS USER GUIDE IV
COPYRIGHT IV
IntroductIon 5
CONTENT OF PACKAGE 5
UNIQUE UNITIRE IDEAS 5
EASY TO USE 5
OVERVIEW 6
SPECIFICATIONS 7
EXAMPLES 8
QuIck GuIde 9
3 WAYS TO PRESS BUTTONS 9
TURN UNITIRE ON 9
MEASURE AND ADJUST THE PRESSURE IN
PRESSURE MODE 9
SAVE THE MEASURED PRESSURE VALUES 10
RECALL STORED VALUES 10
CLEAR THE STORED PRESSURE VALUES 10
TRANSFERRING DATA 10
SETUP MODE 10
TURN UNITIRE OFF 10
BUILT-IN HELP 10
reference GuIde 11
BASIC INFORMATION 11
3 WAYS TO PRESS BUTTONS 12
TURN UNITIRE ON 12
TURN UNITIRE OFF 12
HELP MODE 12
PRESSURE MODE 13
SEQUENCE MODE 14
STEALTH MODE 15
RECALL MODE 17
TRANSFERRING DATA 17
ENTER SETUP MODE 19
GENERAL FUNCTIONS 19
SPORT SETUP 19
SEQUENCE SETUP 19
GAUGE MODE SETUP 19
MAX RANGE SETUP 20
STEALTH MODE SETUP 20
STEALTH TARGET SETUP 20
LANGUAGE SETUP 21
CONTRAST SETUP 21
OPERATION SETUP 22
troubleshootInG 23
BATTERY CHANGE 24
CLEANING 24
MAINTENANCE 24
SERVICE 25
GUARANTEE 25
SERVICE AND GUARANTEE 25
Index 26
Contents Contents

IV
SALES AND SERVICE IN
DENMARK
Unipro ApS
Viborg Hovedvej 24
DK-7100 Vejle
Denmark
Tel [phone]
[email protected]
www.uniprolaptimer.com
www.facebook.com/uniprolaptimer
www.instagram.com/uniprolaptimer
INTERNATIONAL DEALERS
You can nd our International dealers on the
web site:
www.uniprolaptimer.com
DESIGN AND PRODUCTION
Designed and manufactured in Denmark by
Unipro ApS.
The UniTire pressure gauge was designed by
Palle Schultz, Denmark:
www.palleschultz.dk
Unipro reserves the right to make changes and
improvements to any of the products described
in this document without prior notice.
Part numbers:
17-02-001 UniTire V2 (black)
17-02-002 UniTire V2 (dark blue)
17-02-003 UniTire V2 (red)
17-02-004 UniTire V2 (silver)
All part numbers are including a protection
cover.
Spare part numbers:
17-03-030 Button for UniTire handle
17-03-031 Button for UniTire display
17-03-033 Two M4 x 12 stainless screw
17-03-034 Gasket for UniTire handle
17-03-036 Junction cable UniTire
ABOUT THIS USER GUIDE
This guide was written and produced by
Unipro ApS.
UniTire V2 User Guide version 2.00
Made for UniTire V2 rmware version 1.0x.
COPYRIGHT
Copyright © 2022 Unipro ApS
Copyright and acknowledgementsAbout

5
This User Guide contains all relevant information about your new
UniTire digital tire pressure gauge.
Get started with the UniTire in 2 minutes with the Quick Guide.
Read all about the advanced features and functions in the
Reference Guide.
Before you start, please check that your UniTire package contains
the accessories described below.
CONTENT OF PACKAGE
The UniTire package contains the following:
• Pressure gauge.
• Pressure handle 0 - 5 bar.
• Protection cover.
• Two Alkaline AAA batteries installed.
• This User Guide.
If any of these items are missing please contact
your dealer.
Note: You should retain the packaging in case
you need to transport the unit.
UNIQUE UNITIRE IDEAS
UniTire combines many new ideas not seen
before in a tire pressure gauge:
• The pressure sensor is placed directly in
the air handle, which is connected to the
gauge with a exible cable instead of an
air hose. This makes the measurement
very precise because no air is wasted in
the air hose.
• The handle has two air valves, which
makes it easy to use with right or left
hand - and allows you to let out more
or less air.
• The handle is angled in a way which al-
lows easy access to any type of tire valve.
• The standard pressure range is 0-5 bar.
• The ”Stealth mode” enables you to hide
the pressure values from prying competi-
tors, only showing if your tire pressure is
at, above or below target.
• The ”Sequence mode” allows you to save
tire pressure values in a specied order
for later analysis - and do it very quickly!
• The user interface comes in many differ-
ent languages, including Danish, Dutch,
English, French, German and Italian
pre-installed.
EASY TO USE
Even with all the advanced features, the pres-
sure gauge is very easy to use.
The graphical display makes it effortless to
see and analyze the tire pressure saved in the
pressure gauge.
The unique round shape with 4 gray tones is
easy to read, and supports different sizes of
text and numbers.
The graphical display also supports a regular
analog gauge if you prefer this look over the
digital look.
The feedback we get from drivers and teams
about UniTire tells us that we have succeeded
in making the UniTire easy to use.
Introduction
Introduction

6
Please note that the functions of the two but-
tons depend on whether the UniTire is set for
right or left hand operation.
This manual assumes that UniTire is set for
right hand operation.
OverviewIntroduction
LEFT BUTTON
Typically used to change
values. Made of stain-
less steel.
STANDARD BATTERIES
Two standard AAA Alkaline
batteries inside. Long
lifetime.
SYMMETRIC DESIGN
Enables both right and
left handed operation.
HIGH RESOLUTION DISPLAY
The large round high resolution
display gives a quick overview.
HIGH PRECISION
0.0002 bar resolution
and 0.01 bar typical
accuracy.
HANDLE CABLE
Flexible cable with power
and communication for the
handle.
SYMBOLS
Here you might
see the battery
status.
TEXT
UniTire talks
to you in your
own language!
GRAY TONES
Enables
smoothed fonts
and text.
RIGHT BUTTON
Typically used to accept
and store operations.
Made of stainless steel.
DURABLE CASING
UniTire is made of
anodized high quality
aluminum.
STEALTH MODE
Unique mode for
secret tire pres-
sures.
Actual size
1:1
BLUETOOTH
Transfer data to the
Unipro app on your
phone or tablet.

7
Specications Introduction
Pressure range 0 - 5 bar (72.5 psi)
Resolution < 0.0002 bar (0.0029 psi)
Typical accuracy < ± 0.01 bar (0.145 psi)*
Proof pressure 10 bar (145 psi)
Wasted air 0.8 cm3(0.05 inch3)
Communication Bluetooth (BLE)
Real time clock Yes (auto sync with Unipro app)
Power supply 2 x AAA Alkaline batteries
Battery lifetime ~ 200 hours**
Pressure units bar, mbar, psi, HPa, Torr
Languages DEN, FRA, GBR, GER, ITA, NED
Memory 20 tires sets
Dimensions 72.5 x 104.3 x 19.0 mm (2.85” x 4.11” x 0.75”)
Weight 290 g (10.23 ounces)***
Controls Two buttons in stainless steel
Display 128 x 128 pixels, 4 gray tones, bottom view (6 o’clock view)
Calibration Auto calibrate offset after power on
* Typical accuracy: Typical error when used in steady temperature for a limited time.
** Battery lifetime: Measured in pressure mode with new Alkaline batteries.
*** Weight: Includes gauge, batteries, cable and handle.

8
Introduction Examples

9
Quick Guide
3 WAYS TO PRESS BUTTONS
To use UniTire, you need to know how to press
the two buttons in 3 different ways:
1. A short press -
2. A medium press - 11
3. A long press - 33
For the general use of UniTire, it is only neces-
sary to use the short press ( ) and the long
press ( 33). Only secondary features are
operated with the medium press ( 11).
TURN UNITIRE ON
There are 3 different ways to turn UniTire on:
1. Keep pressing the right button ( 3) if you
want to measure and view the current pressure
(Pressure mode).
2. Keep pressing the left button ( 3) if you
want to measure and save the pressure
values of all tires in the predened sequence
(Sequence mode).
3. Press both the left and right buttons at the
same time ( 3+ 3) if you want to change
settings (Setup mode).
UniTire starts by showing the startup screen,
and will show this screen as long as you keep
pressing the button(s). After that you will be
on either the pressure screen (1), the pressure
sequence screen (2) or in the setup mode (3).
MEASURE AND ADJUST THE
PRESSURE IN PRESSURE
MODE
If you start in “Pressure mode”, the screen will
show the current tire pressure. The pressure
value is constantly updated to allow for quick
pressure adjustments.
Use one or both of the air valve buttons on the
pressure handle to reduce the pressure.
If the right button ( ) is pressed, the current
value will be stored in the history list under the
current pressure value. The history list shows
the last four values stored, even after UniTire
is turned off.
If you want to clear the history list, just press
and hold down the left button ( 3) until the
list disappears.
The pressure unit (bar, psi etc.) is chosen in the
setup menu, which is described later in this
manual.
Read the Quick Guide and learn how to use the basic functions
of the UniTire:
Turn UniTire on and off, view current tire pressure, save the pres-
sure values for all tires and recall them later.
You will be ready to go in 2 minutes...
Quick Guide
9

10
Quick guideQuick Guide
SAVE THE MEASURED
PRESSURE VALUES
If you start in “Sequence mode”, the screen
will inform you about which tire you are sup-
posed to measure.
Use one or both of the air valve buttons on the
pressure handle to reduce the pressure.
Measure the tire pressure on the rst tire and
press the right button ( ) to save the value.
Then move on to measure the pressure on the
next tire in the sequence.
The tire sequence is dened in the Setup
mode. This is described in ”SEQUENCE SETUP”
on page 19.
RECALL STORED VALUES
From “Sequence mode” press the left
button ( ) to recall the saved tire pressure
values in “Recall mode”.
The screen will list 4 sets of tires. Depending
on the selected sport, there will be either two
or four tires in each set.
The tires are listed in the same sequence as
selected in Setup mode.
The bottom of the screen will show the current
page and the total number of pages.
UniTire can store values for up to 20 sets of
tires.
Press the right button ( ) to go to the next
page.
CLEAR THE STORED
PRESSURE VALUES
If you want to clear the stored values, just
press and hold down the left button ( 3) from
“Recall mode”.
TRANSFERRING DATA
From “Recall mode” press the left button ( )
to go to “Transfer mode”.
While the transfer screen is active, the
Bluetooth communication is turned on and
running. If the app is active, it can connect to
UniTire and transfer data or settings.
Press the left button ( ) to go back to ”Se-
quence mode”
SETUP MODE
To change settings, press and hold the left
and the right button ( 3+ 3) at the same
time to go to Setup mode - either when turn-
ing UniTire on or during normal operating.
For more information about Setup mode,
please see “ENTER SETUP MODE” on page
19.
TURN UNITIRE OFF
Press the right button ( 3) and hold it down
to turn UniTire off. When you see “POWER
OFF” in the display, you can release the button
again.
UniTire will also turn itself off if no button is
pressed and no pressure is detected after a
preselected time.
BUILT-IN HELP
When you turn UniTire off and “POWER OFF”
is displayed, you can press the left button ( )
before you release the right button, to display
the built-in help.
In help mode, the right button ( ) will show
the next help page, and the left button ( )
will show the previous help page.
To leave help mode, turn UniTire off.
That’s how easy it is! If you are ready for
some more advanced features, then read the
Reference Guide in the following section.

11
BASIC INFORMATION
Batteries
UniTire uses two standard AAA cell batteries.
The software is optimized to be energy-efcient
for long battery life (typically more than 200
hours).
Please help us in our effort to protect the
environment:
1. Do not change the batteries before
UniTire tells you to do so.
2. Always turn in your used batteries for
recycling.
Low battery symbol
When the batteries reach 2.2 V, the low bat-
tery symbol will be shown at the bottom of the
display:
You can continue to use the UniTire until the
last of the 4 ’cells’ in the battery symbol has
disappeared. At 1.75 V UniTire will turn off
automatically.
Pressure handle
The pressure handle is equipped with two air
valve buttons. Use one of the buttons to let out
air, or both buttons to let out more air.
Communication and power cable
The cable which connects the pressure handle
with the pressure gauge carries the power and
communication between the gauge and the
handle.
The cable is very exible and durable, but be
careful not to cut or squeeze the cable with
sharp or heavy objects.
Display, casing and buttons
The UniTire has a custom made, 128 x 128
pixel graphical display with 4 gray tones and
adjustable contrast.
The casing is made of high quality aluminum
and the buttons of stainless steel.
To maximize the lifetime of your Unitire:
• Do not put it directly in your tool box.
• Be careful not to drop it on the ground.
• Do not put it under heavy objects.
• Do not use it in rain.
In the reference guide you can nd detailed information about
all features and functions of the UniTire.
To get the most from your UniTire, we recommend that
you read this guide in full.
The UniTire is optimized for ease of use, while also incorporating
many useful, advanced features.
Reference
Guide
Reference Guide
11

12
Operating UniTire
Reference
Guide
3 WAYS TO PRESS BUTTONS
To use UniTire, you need to know how to press
the two buttons in 3 different ways:
1. A short press -
2. A medium press - 11
3. A long press - 33
For the general use of UniTire, it is only neces-
sary to use the short press ( ) and the long
press ( 33). Only secondary features are
operated with the medium press ( 11).
TURN UNITIRE ON
There are 3 different ways to turn UniTire on:
1. Keep pressing the right button ( 3)
to measure and view the current pressure
(Pressure mode).
2. Keep pressing the left button ( 3) to mea-
sure and save the pressure values of all tires in
the predened sequence (Sequence mode).
3. Press both the left and right buttons at
the same time ( 3+ 3) to change settings
(Setup mode). This is not often used, but you
will need to set up UniTire at least once.
UniTire starts by showing the startup screen
as long as you keep pressing the button(s).
Then you will see the pressure screen (1), the
pressure sequence screen (2) or the setup
screen (3).
Startup screen with software version and
serial number.
TURN UNITIRE OFF
Press the right button ( 3) and hold it down
to turn UniTire off. When you see “POWER
OFF” in the display, you can release the button
again.
UniTire will also turn itself off if no buttons are
pressed and no pressure is detected after a
predened time.
The current time and date is also shown on the
power off screen. This clock can only be set
from the Unipro app.
When you turn UniTire off, you will have
access to the built-in help. Just press the
left button ( ) when the power off screen is
shown.
Power off screen with access to help.
HELP MODE
UniTire has a built-in help feature, with pages
showing which buttons to press to use the
different functions.
In help mode you go to the next page by
pressing the right button ( ) and to the previ-
ous page by pressing the left button ( ).
To leave help mode, turn UniTire off.

13
PRESSURE MODE
The regular tire pressure gauge simply shows
the current tire pressure and continuously
updates when air is released by pressing one
or both of the valves on the pressure handle.
Keep pressing the right button ( 3) at startup
to go directly to Pressure mode.
In Setup mode you can choose if you want
to have the pressure values shown as digital
numbers or as a classic analog gauge.
Also in Setup mode, you can choose if you
want to show the pressure value in bar, psi,
mbar, HPa or Torr.
The chosen unit is shown in the square
brackets in the bottom line of the display.
Digital gauge mode
The digital gauge mode can show both the
current pressure value and a ”history list” with
the last 4 saved pressure values.
To save a current pressure value in the history
list, simply press the right button ( ).
Digital view with large current value and
small history list values.
Each time a new pressure value is put in the
history list, the oldest one drops off the list.
The newest value is at the top. This order is
also indicated by the arrow in the right side of
the display.
The history list will be saved even when UniTire
is turned off.
If you want to clear the history, press and hold
down the left button ( 3) until the history list
disappears.
Analog gauge mode
Because of the graphical display, it is possible
to emulate a classic analog gauge. The scale
goes from 0 to the maximum value dened
in Setup mode (see ”MAX RANGE SETUP” on
page 20.
Analog view with 1 bar chosen as max
range, and a current pressure of 0.57 bar.
Depending on the maximum range, a number
of lines divides the scale to make it fast and
easy to see the current pressure. The current
pressure value is also shown as a precise
number in the display.
Make the maximum range value as low as pos-
sible to make the scale as detailed as possible.
This gives a better resolution between the
lines, making it easier to adjust the pressure
while using the analog scale.
Operating UniTire Reference
Guide

14
SEQUENCE MODE
In Sequence mode you measure and save the
pressure on all tires in a predened order (2
or 4 tires depending on which sport you have
chosen in setup).
You need to dene the order of the tires in
Setup mode (see ”SEQUENCE SETUP” on page
19) before you can use this mode.
Your choice in setup of digital gauge mode
or analog gauge mode will also be used in
Sequence mode.
You can save up to 20 sequences in the
memory so you have easy access to the actual
tire pressure values from a full day of racing
without having to write anything down. Each
sessions is time stamped and can be trans-
ferred to the Unipro app via BLE.
Keep pressing the left button ( 3) at startup to
go directly to Sequence mode.
Digital gauge mode
Digital view with large current value for
Front Left tire, an arrow to show the se-
quence direction and numbers in the corner
showing that you are measuring tire 2 of 4.
Press the right button ( ) to save the value
and move on to the next tire.
If you make a mistake and want to clear the
measurements in the current sequence, press
and hold the left button ( 3) down until the
text shows the rst tire again and the progress
is showing either 1/4 or 1/2.
Analog gauge mode
Analog view with current value for Front
Right tire (FR above the needle) shown as
numbers (below the needle) and as value
on the analog scale.
Also when using the analog gauge mode, you
press the right button ( ) to save the value
and move on to the next tire.
Of course it is up to you to decide if you want
to save the pressure value before or after you
make adjustments to the pressure.
Advantages of the digital gauge mode
As you can see in the description on this page,
the digital gauge mode shows more details
than the analog gauge mode:
• Current tire shown with full name.
• Pressure value in very large text.
• Numbers to show where you are in the
sequence.
• Arrow to show the direction to move in
the sequence.
If you use the Sequence mode, we recommend
that you also use the digital gauge mode to
take advantage of the extra features.
Operating UniTire
Reference
Guide

15
Operating UniTire Reference
Guide
STEALTH MODE
Stealth mode is an alternative way of
using the Sequence mode.
The purpose with Stealth mode is to make it
impossible for your competitors to see your tire
pressure when you are measuring.
When Stealth mode is turned on in setup, you
will see the ”Stealth screen” instead of the
regular ”Sequence screen”.
You will still be able to use the simple pressure
mode to see the actual pressure values when
Stealth mode is turned on - only Sequence
mode is affected.
In Stealth mode, you dene a target pressure
for each tire in setup, and then UniTire shows
if you are on target, above target, or below
target, instead of showing the actual values.
Otherwise, Stealth mode works in the
exact same way as Sequence mode:
To start in Stealth mode, turn UniTire on by
holding the left button ( 3).
Measure the tire pressure in the dened se-
quence order, and save each value by pressing
the right button ( ).
If you want to start over with the current
sequence, press and hold the left button ( 3)
down until the circle shows the rst tire again.
When you save the measured values
in Stealth mode, the actual values are
stored in the memory, so you will be able
to see them in Recall mode.
Stealth mode works both with digital and
analog gauge mode.
Read more about setting up Stealth mode
and Gauge mode in the Setup section of this
manual.
Digital gauge view in Stealth mode
Based on the target tire pressure for each
tire, as dened in setup, the Stealth mode
screen will show if the current pressure is
HIGH (as in this example), LOW or SPOT ON.
The small circle will show which tire you
are supposed to adjust (FR = Front Right in
this case).
At the right side of the display you will see the
bar graph showing how close you are to the
target.
If you are too low, LOW will be highlighted,
and if you are too high, HIGH will be high-
lighted.
When you are within 2% of the selected
target, SPOT ON will be highlighted.
The small square to the right on the bar graph
will show how far you are from the dened
target.
The range of the bar graph is +/- 20%.
To the left you will see between zero and three
arrows pointing up or down. These arrows are
a rough indication of how far away from the
target the pressure is.
They are pointing in the direction you need to
go. If they are pointing up, you need to add
more air, and if they are pointing down, you
need to let more air out.

16
Digital gauge view in Stealth mode
Three arrows means more than 100%
away, two arrows means more than 50%
away and one arrow means more than
10% away. If you are within 10% of the
target, no arrows will be shown.
Analog gauge view in Stealth mode
The analog gauge view has less information
than the digital gauge view. Here it shows
a limited area of the scale, the actual tire
(FL = Front Left) and no actual value as a
number.
The analog gauge view in Stealth mode
has the same functions as in Sequence
mode:
To start in Stealth mode, turn UniTire on by
holding the left button ( 3).
Measure the tire pressure in the dened se-
quence order, and save each value by pressing
the right button ( ).
If you want to start over with the current
sequence, press and hold the left button ( 3)
down until the circle shows the rst tire again.
When you save the measured values
in Stealth mode, the actual values are
stored in the memory, so you will be able
to see them in Recall mode.
Use Stealth offset in pressure mode
When Stealth mode is enabled, an offset can
be added to the current pressure value in
”Pressure mode”. This is to confuse prying
competitors.
For example:
If the offset is entered as -0.20 bar (see
”STEALTH OFFSET SETUP” on page 21) and
the real pressure is 1.65 bar, the value shown
in the display is 1.45.
Pressure mode view in Stealth mode
If a stealth offset is entered in Setup mode,
the pressure value shown is not the actual
pressure value. If no pressure is applied, a
question mark is shown to avoid the stealth
offset being visible.
The values in the history list are the real
values. It is only the current pressure
value with the large digits that is af-
fected.
Operating UniTire
Reference
Guide

17
RECALL MODE
The Recall mode is where you view the tire
pressure values you have saved in Sequence
mode / Stealth mode.
You can store up to 20 sequences with either
2 or 4 tire pressure values in each sequence
(depending on the chosen sport).
To enter Recall mode, press the left but-
ton ( ) from either Sequence mode or
Stealth mode.
The recall screen will show either two
or four tires, listed in the sequence you
selected in setup. In this example you see
page 1 of 2.
The rst line will always show the new-
est saved value.
When you measure more than 20 sets of tires,
the oldest one will be erased and the new one
will be stored.
Each page in Recall mode can show four
different sequences with either 2 or 4 tires in
each.
In the bottom right corner you can see which
page you are on, and how many pages there
are in total. This example is showing page
1 out of a total of 2 pages. The maximum
number of pages is 5.
The pressure values use the unit selected
in Setup mode. The unit is shown in square
brackets at the bottom of the screen.
Navigating the pages is easy
To go to the next page just press the right
button ( ). When you reach the last page, a
press on the right button ( ) will bring you to
the rst page again.
If you want to go back to the rst page before
you reach the last page, you can press a little
longer on the right button ( 1).
If you want to clear the memory, press and
hold the left button ( 3).
TRANSFERRING DATA
To enable the Bluetooth communication in
UniTire, simply press the left button ( ) from
Recall mode. This will bring you to the follow-
ing screen.
Transfer screen, UniTire is ready to be con-
nected to.
“CONNECTABLE” means that UniTire is ready
to connect to your phone running the Unipro
App. “UniTire_1293” is the Bluetooth name
including the serial number.
After you connected the app to your UniTire,
the following screen will be shown.
Operating UniTire Reference
Guide

18
Reference
Guide Operating UniTire
Transfer screen, connected to the app.
When the app is connected, it now controls
UniTire. The rst thing it does is to synchronize
the time and date.
From the app, you will be able to do the
following:
• Synchronize the time and date.
• Set the owner’s name.
• Update the rmware.
• Transfer the pressure and temperature.
• Change all settings.
When transfer is in progress, you will be able
to see the progress bar change.
Transferring data to/from the app.
When you leave the transfer screen again, the
Bluetooth is powered down, and the app is no
longer able to connect to UniTire.
To go back to either Sequence mode or Stealth
mode, press the left button ( ) again.

19
Reference
Guide
Setup mode
ENTER SETUP MODE
You enter Setup mode by pressing both the
left and right buttons at the same time
(3+ 3).
You can also do this to go directly to Setup
mode when turning UniTire on.
GENERAL FUNCTIONS
In Setup mode you use the right button ( )
to accept the value, store it in the memory and
move on to the next setup screen.
You use the left button ( ) to scroll through
choices, and to change or adjust the current
setting.
When you are nished with the setup, you can
return to the previous mode by pressing and
holding both the left and the right buttons
(3+ 3) or turning UniTire off by pressing
and holding the right button ( 3).
All settings are stored and will not be cleared,
even if you remove the batteries.
SPORT SETUP
UniTire can be used for all sports where tire
pressure measurements are needed. Choose
your sport - or a sport with the same number
of wheels as your sport.
The “SET SPORT screen” will list the pre-
dened sports.
Scroll between choices by pressing the left but-
ton ( ). Select and move to the next setup screen
by pressing the right button ( ).
When the sport is changed, overwriting values
needs to be conrmed on the next screen.
SEQUENCE SETUP
This is where you dene which order to mea-
sure your tires in.
The “SET SEQUENCE screen” will list all the
possible combinations of tires.
Scroll between choices by pressing the left
button ( ). Select and move to the next setup
screen by pressing the right button ( ).
GAUGE MODE SETUP
UniTire can display in either digital or analog
gauge view. The digital view has more details,
while the analog view is more simple and has
the looks of an old fashioned analog pressure
gauge.
The “GAUGE MODE screen” gives you the
choice between Digital and Analog view.

20
Reference
Guide Setup mode
Scroll between choices by pressing the left
button ( ). Select and move to next setup
screen by pressing the right button ( ).
MAX RANGE SETUP
If UniTire is set to operate in analog mode, it is
necessary to set the maximum pressure value
you wish to display.
You want to have the maximum range value as
low as possible to make the scale as detailed
as possible. This provides resolution between
the lines and easier pressure adjustment while
using the analog scale.
UniTire can measure pressure values up to
5 bar even if the max range is set to a lower
value.
Scroll between choices by pressing the left
button ( ). Select and move to next setup
screen by pressing the right button ( ).
STEALTH MODE SETUP
This is where you choose if you want to use
the Stealth mode when measuring and storing
tire pressure in Sequence mode.
Set Stealth mode to On if you want to hide
pressure values.
Scroll between choices by pressing the left
button ( ). Select and move to next setup
screen by pressing the right button ( ).
STEALTH TARGET SETUP
When Stealth mode is enabled, 2 or 4 more
screens are shown, depending on the chosen
sport.
This is the hidden target pressure value for
each tire.
Increase the target value by pressing the left
button ( ). If you keep pressing the left but-
ton ( 3), the value will increase faster.
To change between increasing and decreasing
the pressure target, just press the left button a
little longer ( 1).
The direction is indicated by the small arrow.
To start from zero, press the right button a
little longer ( 1).
Select and move to the next setup screen by
pressing the right button ( ).