Unit UT310 Series User manual

P/N:110401103773X
DATE:2018.06.26
REV.2

CONTENTS
I. Introduction to UT312 Product----------------------------------------------------------------------------1
II. Unpacking Inspection---------------------------------------------------------------------------------------2
III. Safety Notices------------------------------------------------------------------------------------------------ 2
IV. Instrument Structure----------------------------------------------------------------------------------------3
V. Instrument Setup and Operation-------------------------------------------------------------------------4
VI. Technical Indicators-----------------------------------------------------------------------------------------6
VII. Maintenance--------------------------------------------------------------------------------------------------7

Working principle:
Acceleration sensor
Wave filter Integer I Adjustment I
Integer II Adjustment II
AC/DC A/D LCD
II.UNPACKING INSPECTION
III.SAFETY NOTICES
UT-312 vibration meter is a split portable vibration measurer which consists of acceleration
sensor and digital measurement display circuit. It is mainly used to measure vibration
displacement, speed (or intensity) and acceleration of mechanical equipment. Current status
(such as excellence, notice or danger) can be determined for equipment (such as fan, pump,
compressor and motor, etc) by above measuring data according to enterprise & machine
standards by comparing with national metrological verification regulations of JJG 676-2000
working vibration meter.
Such instrument has measuring value locking, low-voltage prompt and automatic shutdown
functions. With advantages such as wide measurement scope, simple operation and
convenient carrying, it can be used for patrol detection of equipment vibration in power,
metallurgic and petrochemical industries widely so it is an ideal tally instrument.
I.INTRODUCTION TO UT312 PRODUCT
Please unpack and check if following items are deficient or damaged or not. Please contact
the nearest sales service agent of our company if there is any deficiency or damage.
1. Host--------------------------------------------------------------------1set
2. Sensor (with magnetic base)------------------------------------1 (standard) pcs assembled to host
3. Signal wire of sensor----------------------------------------------1 (standard) wire assembled to host
4. Hanging rope--------------------------------------------------------1 (standard) wire assembled to host
5. 9V battery------------------------------------------------------------1 section
6. Manual----------------------------------------------------------------1 book
7. Certificate-------------------------------------------------------------1 sheet
Warning: Please pay attention to possible danger and conditions for user or damage
factors for vibration meter!
Please use vibration meter according to steps shown in the manual or it may be damaged.
Please abide by following guidelines to avoid instrument damage.
To check if shell is ruptured or lacks of plastic pieces or not before using vibration meter.
Please do not use vibration meter with damaged shell.
Please replace battery as soon as possible to avoid error of measuring data if battery symbol
of appears.
Please do not continue to use vibration meter which operates abnormally. Please send it to
fixed repair agent of our company for repair.
Please do not use vibration meter in wet environment with combustible and explosive gas.

IV.INSTRUMENT STRUCTURE
Vibration acceleration
Vibration speed
Vibration displacement
1.
2.
3.
Vibration acceleration
Vibration speed
Vibration displacement
V.INSTRUMENT SETUP AND OPERATION
Please do not detach shell of vibration meter to avoid damage.
Please do not try to charge battery to avoid personal injury due to battery explosion. Please
pay attention to + and - poles during battery installation.
Please pay attention to protect LCD of vibration meter to avoid scratch or crush.
1. Instrument structure (shown in Figure 1 and Form 1)
1.Signal wire of sensor 2.Sensor
3. LCD 4.Three-gear toggle switch
5.Shell
6.Measurement key
signal wire of sensor
sensor
LCD
three-gear toggle switch
shell
measurement key
2. Symbol (shown in Figure 2 and Form 2)
3. Key instructions (shown in Figure 1)
The 5 element shown in Figure 1: Measurement key button
1.Battery installation
Please open cell box on the instrument back and then install 6F22 type 9V laminated cell into
cell box. Please pay attention to polarity then cover it.

2.Power Inspection
Please press measurement key and observe display. Battery replacement mark in the left end
of display shows low battery voltage and prompt of battery replacement. No mark refers to
normal voltage for measurement. (Machine will power off automatically 1 minute after
loosening the key.)
3.Selection of measurement mode
Please toggle measurement selection switch of vibration meter to select measurement
acceleration, speed or displacement. Right arrow on display will point to selected
measurement unit.
4.Measurement
Please connect signal wires connected to sensor to input connector of left sensor then absorb
sensor with magnetic base to vertical cross section of measured article during usage for the
1st time. Instrument can enter into measurement status instantly by pressing measurement
key by thumb. Measuring value will be maintained after loosening the key. Measurement also
can be continued by pressing measurement key again. Data will be maintained for 1 minute
after loosening the key and instrument will power off automatically at the same time. (Note:
Please tighten clasp when connecting signal wires and hold instrument and sensor in hands
after measurement. It is not allowed to hoist sensor by signal wires to avoid influence to
service life of such wires.)
LCD display: 3 1/2-bit display; The maximum display: 1999
Under-voltage display:
Sensor type: Acceleration sensor
Power demand: 1 6F22 9V carbon or alkali battery
Service life: To operate for more than 20 hours continuously
Outline dimension: 185 (H) * 68 (W) * 0 (D) mm (for host)
Weight: About 300g (including battery)
2.Environment Limitation
Indoor usage
Safety standard: GB 4793, 1-2007
Pollution level: Grade 2
Operation temperature & humidity: 0 ~40 (not more than 90%RH)
Storage temperature & humidity: 0 ~+40 (not more than 80%RH)
Atmospheric pressure: 75~106KPa
3.Technical Specification
Accuracy: 5% of 1 word (% of reading + word quantity); Correction period is 1 year;
Ambient temperature: 0 ~40
Ambient humidity: 80% RH
Temperature coefficient: 0.1*(accuracy)/
VI.TECHNICAL INDICATORS
1. General Specification

Vibration measurement scope
~~~
Measurement unit
Range
Frequency response
scope and amplitude error
Linear error of amplitude
Vibration
acceleration (O-P)
Vibration
speed (RMS)
Vibration
displacement (P-P)
VII.MAINTENANCE
Warning: It is not allowed to scratch LCD of vibration meter during battery replacement
and measurement to avoid damage or influence to measurement precision. It is also not
allowed to charge replaced battery to avoid personal injury due to explosion!
1. Battery installation and replacement
Be sure to replace battery in a timely manner when symbol of appears for vibration
meter. Battery replacement method is as follows:
Removing cell cover: Please replace 6F22 9V battery by the same model. Please do not
install improper battery.
Please pay attention to + and - polarity during battery installation.
Please install cell cover after installation.
2. General Maintenance
Please inspect signal wires of sensor constantly because instrument may not display due to
damage or poor contact of such wires. It is not allowed to pull or drag signal wires forcefully.
Sensor core is closed completely. It can not be detached except sensor signals.
Please clean dirty instrument shell by wet cloth and neutral detergent. Please do not use
abrasive or solvent.
Please send damaged vibration meter to fixed repair agent or professional repair personnel of
our company if required. Please do not try to repair it individually.
Please do not scratch or contaminate LCD of vibration meter during usage to avoid oil stain,
water leakage, damage or influence to it.
Please take battery out if it will not be used for a long time.
Please do not store instruments in wet environment and strong magnetic field under high
temperature.
3.Common Troubleshooting
Common troubles
No bootstrap
Without signal input
Display of double arrows by gear switchover
Tripping display or system halted
Possible reason
Poor battery contact
Broken signal wire
Poor toggle of toggle switch
Broken toggle switch or poor toggle