Unitech Tashi MT380 Proximity User manual

A Versatile Multi-Function Terminal
Installation Guide
400640G Version 1.2

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
2
Mounting MT380
Mounting Position
The total angle of view of the camera lens is 68.7 degrees. The depth of field is from 350mm to infinity.
Depending on the individual’s height, the average height for the controller installation is 1550mm, so
the center of the lens coincides with the line of vision. You can adjust the height accordingly to fit into
the angle of view.
Given a distance between the user and controller is 500mm. The focal length of the camera lens about
a vertical axis is 550mm at this given distance.
The following sections will describe the two ways to install and mount MT380: In wall and on wall.
In Wall Installation
Mounting Kit
Mounted Screw (STP-35) x4
Plastic Conical Anchors x4
Screw_FPHM2-5L_TP-P x4
In Wall Metal Frame x1 Metal Spring x4
3*16mm
3*25mm
2*5mm

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
3
1. Put MT380 on the wall and mark the device location aligning with an average height of 1550mm
from the ground level to the center of lens. You can adjust the height accordingly to fit the pan-
toscopic angle 68.7º.
2. Take out MT380, drill a rectangle on the wall with dimension W97mm x H225mm x D35mm.
Unit: mm
68.7º
Unit: mm

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
4
3. Put the metal frame on the rectangle and mark the four screw holes location. Take out the metal
frame, drill the screw holes with size 7/32 inch. Depth of screw: 30mm.
Unit: mm

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
5
4. Insert four plastic conical anchors on the screw holes. Screw the metal frame in the wall with
mounted screws (STP-35).
5. Insert the stripped end of the wire into respective terminal block position of the male plug (See
Using Terminal Block on page 14), then tighten the lock screw to secure the wire.
Lock Screw
1
2
3
4
5
6
7
8
9
10
11
12

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
6
6. Locate the I/O panel on MT380’s rear cover, and remove the I/O panel by twisting a Philips
screwdriver on the cross mark.
7. Insert the terminal block plug into the female socket of MT380.

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
7
8. Locate four In Wall Mounting Holes on MT380:
9. Put four Metal Springs on MT380 and screw them with four Screw_FPHM2-5L_TP-P to com-
bine the terminal and metal springs.

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
8
10. Put the terminal in the rectangle hole and mount MT380 terminal on the metal frame. (Only the
panel of the terminal is exposed)
Side View of MT380 In Wall
Unit: mm

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
9
On Wall Installation
Mounting Kit
1. Put MT380 on the wall and mark the device location aligning with an average height of 1550mm
from the ground level to the center of lens. You can adjust the height accordingly to fit the pan-
toscopic angle 68.7º.
Mounted Screw_STP-35 x4
Plastic Conical Anchors x4
Screw_M3*6 T10 x1
On Wall Metal Frame x1
3*16mm
3*25mm
3*6mm
Unit: mm
68.7º

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
10
2. Take out MT380, put the metal frame on the wall and mark the four screw holes location. Take
out the metal frame, drill the screw holes with size 7/32 inch. Depth of screw: 30mm.
Unit: mm

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
11
3. Insert plastic conical anchors into the screw holes. Put the metal frame on the wall, and screw
the metal frame with mounted screw (STP-35).
4. Insert the stripped end of the wire into respective terminal block position of the male plug (See
Using Terminal Block on page 14), then tighten the lock screw to secure the wire.
Lock Screw
1
2
3
4
5
6
7
8
9
10
11
12

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
12
5. Locate the I/O panel on MT380’s rear cover, and remove the I/O panel by twisting a Philips
screwdriver on the cross mark.
6. Insert the terminal block plug into the female socket of MT380.

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
13
7. Locate four On Wall Mounting Holes on MT380.
8. Mount the terminal and screw the bottom part of the terminal with one Screw_M3*6 T10.

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
14
Using Terminal Block
Pin Assignment
Relay Output
Digit Input
D1+ and D1- are the positive and negative nodes of the external power input.
D2+ and D2- are the positive and negative nodes of the external power input.
Pin Name Description
1 12V DC Out, support +12V, 0.5A
2GND GND
3 D1+ Photo-In Anode(-)
4 D1 - Photo-In Cathode(+)
5 D2+ Photo- In Anode(-)
6 D2 - Photo-In Cathode(+)
7 R1-C Common
8 R1-NONormal Open
9 R1-NCNormal Close
10 R2-C Common
11 R2-NONormal Open
12 R2-NCNormal Close
RL1-CTRL →High R1 (C & NO Linked)
RL1-CTRL →Low R1 (C & NC Linked)
RL2-CTRL →High R2 (C & NO Linked)
RL2-CTRL →Low R2 (C & NC Linked)
D1 = High Digit input1 = High
D1 = Low Digit input1 = Low
D2 = High Digit input2 = High
D2 = Low Digit input2 = Low
1
2
3
4
5
6
7
8
9
10
11
12