UNITED USF-654 User manual

16”Metal Stand Fan With Remote Control
MODEL: USF-654
SAFETY PRECAUTIONS
When using any electrical appliance, basic safety precautions should always be followed, including the
following:
1. Read all instructions and keep for future reference.
2. This appliance is not intended for use by persons (including children) with reduced physical,

1
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
3. Young children should be supervised to ensure that they do not play with the appliance.
4. Always unplug the appliance from the mains when not in use.
5. To disconnect the appliance, switch the control to OFF, then unplug from the mains.
6. To unplug the appliance, always grasp the plug; do not pull the cord.
7. If the supply cord is damaged it must be replaced by the manufacturer, its service agent or a
similarly qualified person in order to avoid a hazard.
8. Do not use outdoors. This appliance is designed for household use only.
9. Place the power cable away from areas where people walk so that it cannot be stepped on or
tripped over.
10. Always use the appliance on a flat, stable surface.
11. Never clean this appliance when it is plugged in .Do not immerse it in water, Clean the outside
surface with a damp cloth or soft brush and dry with a soft dry cloth.
12. Use the appliance only as directed in this manual. Misuse could void your warranty.
13. Avoid contact with moving parts, never insert any objects through the grille when the fan is in
operation.
ASSEMBLY INSTRUCTIONS:
Base Assembly
1. Unscrew the Ring and
Base Locking Screw from the
Stand Assembly.
2. Insert the Stand Assembly through
the hole in the center of the Stand Base
and twist into position.
3. Turn the Stand Base upside down with
the Stand Assembly facing the floor
and place the Base Weight Support to
the bottom of the Base.
Tighten the Base Weight Support
to the Stand Base by screwing back
the Ring and Base Locking Screw
Stand
Assembly

2
Fan Head Assembly
1. There are two knobs at the Connector; the smaller one is the Tilt Knob and the bigger one is the
Locking Knob. Unscrew the Locking Knob to loosen the Thread Bolt.
2. Pull Telescopic Inner up to your desired height and lock in place by tightening the Height
Adjustment Screw
3. Place the Motor onto the Telescopic Inner. Align the holes on the Connector and the Telescopic
Inner. Install the Motor to the Telescopic Inner by tightening back to Thread Bolt with the Locking
Knob.
Final Assembly
1. Position the Rear Grill over the Motor Shaft, making certain the 2 notches at the Rear Grill fit
over the 2 prongs on the Motor Housing .Make sure the Rear Grill fits securely against the Motor
Housing.
2. Secure the Rear Grill to the Motor Housing with the four Rear Grill Locking Screws. Loosen the
grill locking screw at the bottom of the Rear Grill and save it.
3. Install the Fan Blade onto the Motor Shaft by tightening the Blade screw to the Motor Shaft.
4. Centre the Front Grill by aligning the logo on the grill Hub so it is horizontal and parallel to the
floor. Then secure the Front and Rear Grills completely together by snapping grill clips into place.
Lastly, tighten the grill locking screw at the bottom of the Rear Grill.
6. Place the Control box on the holes of the Telescopic Inner, then fix it with the Control Box Screw.

3
REMOTE CONTROL
1. Put two batteries (TypeAAA,1.5V) into the battery compartment of the remote control and close
the cover until it clicks into place. The maximum distance for transmitting signals from the
remote control to the fan is 6 meters. Make sure that no objects are hindering signal
transmission.
2. Take the protective film off the remote control.
3. Use only batteries of TypeAAA,1.5V and after replacing the old batteries dispose of them for
recycling and according to your local regulations.
4. If you do not wish to use the remote control for a longer period (4 weeks or more), take the
batteries out of the remote control.
OPERATING INSTRUCTIONS
Ensure voltage used corresponds with the voltage indicated.
b) Use the remote control to select the speed.
c) Tilting angles-By pushing the tilt-guard, you can adjust the fan to your desired elevation.
d) Never touch the blades with hand or any object!
e) Do not pull the cord grip the plug itself. If the cord or plug are get damaged, They must be checked
by a qualified repairer before further use.
CLEANING AND MAINTENANCE INSTRUCTIONS:
To clean: Disconnect the power cord from the mains. Remove the guard and the blades carefully.
Do not drop the blades! First use soft cloth with light soap to clean off oil stains. Then wipe and polish
with dry cloth. Never use polish or any corrosive liquid that will damage the paint, metal or plastic! Put
back the blades and lock the guard securely before use.
WARNING: Unplug from electrical supply source before cleaning. After servicing, any safety device
(including grilles and blades) must be reinstalled or remounted as previously installed. Use soft damp
cloth then wipe with dry cloth. Do not use harmful cleaners. Do not bend the blades.
If the plug and supply cord are damaged, it must be replaced by the manufacturer, its
service agent or a suitable qualified person in order to avoid a hazard

4
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste. Please dispose of this
equipment at your local community waste collection/ recycling centre.
In the European Union there are separate collection systems for used electrical and electronic
products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
This product complies with the requirements of Directives:
EMC-Directive: 2004/108/EC
Low Voltage Directive: 2006/95/EEC
RoHS2 Directive: 1 1/6 5/ E U
The above directives declare that this model is in compliance
with following norms:
EN 55014-1/A2:11
EN 55014-2/A2:08
EN 61000-3-2/A2:08
EN 61000-3-3:08
EN 61457:09
EN 60335-2-80:03/A2:09
EN 60335-1:12/A11:14
EN 62233:08
IEC 62321:08, IEC 62321-1:13, IEC 6232-3-1:13, IEC 62321-4:13, IEC 62321-5:13
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savvidis S.A.
87Α, 17th November Str - P.C. 55535
Pylaia - Thessaloniki - Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr
www.united-electronics.gr