UNITED USF-679 User manual

INSTRUCTION MANUAL
READ AND SAVE THESE INSTRUCTIONS
Model: USF-679

When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. To prevent fire or shock hazard, DO NOT expose this appliance to rain
or moisture.
2. Dangerous high voltages are present inside this enclosure. To avoid
electric shock, DO NOT open the cabinet, refer servicing to qualified
personnel only.
3. This appliance is intended for household use only and not for
commercial, industrial or outdoor use. Other use not recommended
may cause fire, electric shock or injury.
4. Ensure the fan is not placed near drapes,curtains, or any objects that
may be drawn into the fan.
5. To protect against fire, electrical shock and injury to persons, do not
immerse the unit, plug or cord in water or spray it with liquids.
6. The apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
product.
7. No naked flames sources, such as candles, should be placed on the
product.
8. Ventilation should not be impeded by covering the ventilation
openings. Slots and opening are provided for ventilation to ensure
reliable operation of the product and to protect it from overheating.
9. Care required with the use of this apparatus in tropical climates. Do
not use the appliance to temperatures over 40 °C.
10. Place the fan on a stable level and dry surface when operating to
avoid overturning.
11. Only connect to a suitablyAC 220-240V~50Hz mains socket.
12. Do not operate the fan in the presence of explosive and/ or flammable
fumes. Do not place the fan or any parts near an open flame, cooking
or other heating appliance.
13. Do not operate the fan with a damaged cord or plug, after a
malfunction or if it is dropped or damaged in any manner.
14. Do not operate the fan without the fan grilles properly in place.
15. Do not place the fan close to an open window. Rain splashing on the
fan could cause an electric shock hazard.
16. Do not let the power cord hang over the edge of a table or counter or
let it touch any hot surfaces.
17. Do not insert or allow foreign objects to enter the grille openings as
this may cause damage to the appliance.
18. Do not use the fan if grille becomes damaged or loose.
19. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible
for their safety.
20. Children should be supervised to ensure that they do not play with the
appliance.
21. Switch the fan OFF and unplug it from the outlet when it is not in use,
when moving fan from one location to another and before cleaning.
22. To disconnect, grip the plug and pull it from the wall outlet. Never pull
by the cord.
23. Do not attempt to repair, disassemble or modify the appliance. There
are no user-serviceable parts inside. Refer all servicing to qualified
service personnel.
WARNING
• TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK,
DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL
DEVICE.
• UNPLUG OR DISCONNECT THIS FAN FROM THE POWER SUPPLY
BEFORE SERVICING.

Components:
Description：
1. Logo ring 2. Guard front
3. Safe screw 4. Safe nut
5. Logo ring screw 6. Blade lock
7. Blade 8. Guard lock
9. Guard back 10. Motor
11. Hand for neck 12. Body
13. Power cord 14. Button
15. Hand for column 16. Column nut
17. Column 18. Base screw
19. Foot cup 20. Base
21. Base weight 22. Base nut

Before first use
Unpacking: This product has been packaged to protect it against
transportation damage. Unpack the appliance and keep the original
packaging carton and materials in a safe place. It will help prevent any
damage if the product needs to be transported in the future, and you can
use it to store the appliance when it is not in use. In the event it is to be
disposed of, please recycle all packaging materials where possible.
Safe packaging disposal: Plastic wrapping can be a suffocation hazard
for babies and young children, so ensure all packaging materials are out of
their reach and disposed of safely.
Inspection: Unwind the cord to its full length and inspect it for damage. Do
not use the appliance if the appliance or its cord have been damaged or
are not working properly. In case of damage, contact our after sales
support line for advice on examination, repair or return of the
damaged product.
Assembly
Your new fan has been shipped partially assembled to reduce wastage of
packaging material, paper cartons and weight. Follow the drawing above to
assemble it; the illustration opposite shows how all the parts fit together.
1. Take out the base screw and nut ( 18 and 22 ) from the small plastic
bag to connect column ( 17 ) , base( 20 ) and base weight ( 21 ) together
and tighten screws .
2. Loosen the column nut (16) at the top of the column and pull out the
extension pole to the desired height, or all the way to the top for maximum
height (you may have to push it up from the bottom if it is tight or stuck). At
the desired height, turn the column nut clockwise to tighten securely.
3. Lightly loosen the hand for column (15), attach the fan body to the top
of the extension column. Push the body down as far as possible and then
tighten securely with the set screw.
4. Unscrew guard lock (8) and remove it from the motor shaft.
5. Position the rear guard (9) through the motor shaft against the motor
housing, placing the vertical holes in the guard over the two pins on the
housing. Make sure the handle is on top. Screw on the guard lock in
clockwise direction to hold the rear guard securely in place.
6. Place the blade(7) on the motor shaft. Secure the blade with the blade
lock(6), turning it anticlockwise to tighten.
7. Assemble the logo ring (1) on front guard (2) , then assemble front
guard and rear guard together by tighten the guard nut . Finally assemble
the safe screw and nut ( 3 and 4 ) at the bottom of guard.

Instructions
Place the fan on a dry, level surface, plug it into a 240V 50Hz electrical
outlet and switch on power to the outlet. All available settings options will
start flashing on the control panel. Ensure the remote control contains two
AAA size batteries (not supplied).
Remote control operation
This fan is equipped with 3 speeds, 3 modes, a 7.5hr timer and a remote
control for convenient operation. (You can also use the control panel to
switch the fan on and off, select a speed, set the timer and oscillation.)
1. Mode button
2. Timer button
3. ON / SPEED button
4. OFF button
5. SWING BUTTON
ON/SPEED
Press the ON/SPEED button (on the remote control or on the control
panel) to switch on the fan. On subsequent operations the fan will start at
the last selected settings.
Press the ON/SPEED button again to select HIGH or LOW speed.
OFF
Press the OFF button to switch off the fan.

MODE
Press the MODE button (on the remote control) to change the fan mode
through different breeze modes.
Normal: In this mode the fan operates at a constant speed. The mode
indicator is red.
Natural: In this mode the fan simulates a natural breeze mode by
cycling on and off, as in nature.
Sleep: In this mode the fan simulates a soft, natural breeze suitable for
night-time use.
SWING
Press the SWING button (on the remote control or on the control
panel) to activate the oscillation function for widespread breeze
distribution.
Press the button again to stop oscillation when the fan head is in
the desired position.
TIMER
Press the TIMER button (on the remote control or on the control
panel) to set the timer in increments of 0.5 hour to a maximum of 7.5
hours.After the timer runs out, the fan will automatically shut off.
There are four indicator lights for the timer: 0.5h, 1h, 2h, 4h. For example: *
0.5h illuminated indicates the timer will shut off after 30 minutes. * 0.5h and
2h illuminated indicates it will shut off after 2.5 hours. * 0.5h, 1h, 2h and 4h
illuminated indicates it will shut off after 7.5 hours.
MAINTENANCE
Always turn off the fan and remove the plug from the socket-outlet
before cleaning.
Clean the external surfaces of the fan with a soft damp (not
dripping wet) cloth.
WARNING:
Do not immerse the fan in water.
Do not use any cleaning chemicals such as detergents and
abrasives.
Do not allow the interior (special for the PCB) to get wet as
this could create a hazardous situation.
When the unit is not in use, make sure that it is unplugged from the
wall socket. To store the fan, you may pack it in the original carton
and store it in a cool and dry place until later use.
In case of malfunction or doubt, do not try to repair the fan yourself;
it may result in a fire hazard or electric shock.

NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high
quality materials and components which can be recycled
and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life,
should be disposed of separately from your household
waste. Please dispose of this equipment at your local
community waste collection/ recycling centre.
In the European Union there are separate collection systems for used
electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the
requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at
www.united-electronics.gr
Exclusive importer in Greece:
Amiridis –Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki –Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr
www.united-electronics.gr