Universal Furniture 414-280 User manual

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
414-280/28F/28R
414-290/29F/29R
Poster Bed 5/0 6/6
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Headboard
1pc
B
Footboard
2pcs
C
Bed Foot
2pcs
D
Side rail
2pcs
E
Slat
3pcs
F
Support leg
3pcs
G
Lower Post
2pcs
H
Center Post
4pcs
I
Finial
4pcs
J
Upper Post
4pcs
K
Mushroom cap
2pcs
L
Hardware Pack
1bag
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Put the footboard (B) upright down on a soft and smooth surface to avoid damage or being
scratched. Then attach the bed feet (C) to footboard (B) by hand.
Step 3: Attach the side rails (D) to the headboard (A) and footboard (C) with nut (1), spring washer
(2), curved washer (3) and bolts (4) using wrench (5). And attach the support leg (F) to the
Slat (E) by hand. Then screw the slats (E) to the side rails (D) using screwdriver (not
provided).
Step 4: Attach the posts (G&H&J) and finial (I) to the top of headboard (A) and footboard (B). And
also you can use mushroom cap (K) for footboard (C) as below shown.
Note: 1. 414-290/29F/29R has 6 pieces support legs.
2. There are several options for the posts assembled. You can freely change it according to
your habit.
Assembly is now complete.

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
414-280/28F/28R
414-290/29F/29R
Poster Bed 5/0 6/6
1
Q'TY
2
SPRING WASHER 8 PCS
5/16"
8 PCS
5/16"
5/16"*3"
5/16"L32*13*8mm
8 PCS
NUT
CURVED WASHER
BOLT
WRENCH
WOOD SCREW
1 PC
8 PCS
6 PCS
3
4
5
6
#8*1-1/4"
87*19*2.5mmT
HARDWARE LIST(L)
Step 2
BC
6
A
D
E
5
1
2
3
4
F
Step 3

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
414-280/28F/28R
414-290/29F/29R
Poster Bed 5/0 6/6
H
I
I
I
I
G
G
H
H
J
J
K
Step 4