Universal Furniture 192380 User manual

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
192380 & 193380
Bed Bench (Upholstered)
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the assistance
of one or more persons in order to prevent personal injury and to insure parts are not damaged during the
assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution applied on damp
cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for packaging
carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to the
furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Side frame
2pcs
B
Seat board
1pc
C
Back rail
1pc
D
Stretcher
2pcs
E
Middle Stretcher
1pc
F
Cushion
1pc
Assembly Procedure:
Caution: Please do not over-tighten bolts during assembly.
Note: First read the bench leveling instructions. This is an additional assembly instruction sheet found
inside the carton.
Step1: Place all bench parts on a soft and smooth surface.
Step2: Take off plastic cover on upholstery seat. Assemble middle stretcher (E) to the stretcher (D)
using screw #3. Tighten them completely with screwdriver (not provided).
Step3: Assemble back rail (C) to bench leg and side frame (A) using #1 (bolt + lock washer + flat
washer) and horizontal hole nut #6. First, insert the horizontal hole nut into hole of back rail (C),
then you need to adjust horizontal hole nut to line up with back rail so that #1 bolt will assemble
properly, finally tighten the bolt with allen wrench #5. Don’t over tighten.
Step4: Assemble seat board (B) to side frame (A) using #1 (bolt + lock washer + flat washer) and
horizontal hole nut #6.
Step5:.Make sure the seat board (B) in the middle of side frames (A) using screw #2. Tighten them
completely.
Step6: Attach end of stretcher (D) to side frames (A) using #1 (bolt + lock washer + flat washer) and #6
horizontal hole nut. Tighten all bolts completely using allen wrench #5. The other side same as
steps above. Then, Attach wooden plugs #4.

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
192380 & 193380
Bed Bench (Upholstered)
Hardware List QTY
NO.
1
2
3-1/4" L
1" L
Bolt+Spring Washer+Flat Washer--1/4" dia 10pcs
4pcs
1pc
Allen Wrench
Wooden Plug
Wood Screw 2pcs
10pcs
Horizontal Hole Nut
Screwdriver
10pcs
1pc
Wood Screw
1-3/8" L
3
4
5
6
7
C
B
D
B
D
3
3
D
hole
Attention:
Step7: After making sure all bolts are attached and hand tightened, turn the bench over.
Step8: The cushion (F) flat on the seat board (B).
Step9: Level the bench following “Chair Leveling Instruction”. This is an additional assembly instruction
sheet found inside the carton.
Step10: Make sure the bench is level and tighten all bolts completely using the wrench supplied.
Assembly is now complete.