Universal Furniture Explore Home 932-634 User manual

Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Chair Back
1 pc
B
Seat Frame
1 pc
C
Left Leg
1 pc
D
Right Leg
1 pc
E
Stretcher
1 pc
Assembly Procedure:
CAUTION: PLEASE DO NOT OVER-TIGHTEN BOLTS DURING ASSEMBLY.
NOTE: FIRST READ THE CHAIR LEVELING INSTRUCTIONS. THIS IS AN ADDITIONAL
ASSEMBLY INSTRUCTION SHEET FOUND INSIDE THE CARTON.
Step 1: Place all chair parts on a soft and smooth surface.
Step 2: Assemble Chair Back (A) to back rail of Seat Frame (B) using Bolt (3), Lock Washer (5) and
Flat Washer (6). Tighten with Wrench (7).
Step 3: Assemble rear corner blocks of Seat Frame (B) with back post using Bolt (1), Lock Washer
(5), and Flat Washer (6). Tighten with Wrench (7). There are 4 bolts in total.
Step 4: Assemble Stretcher (E) to chair back by using Screws (4). Tighten screws with screwdriver.
(Not provided)
Step 5: Assemble front corner blocks of Seat Frame (B) with Right leg (D) & Left leg (C) using Bolt
(2), Lock Washer (5) and Flat Washer (6). Tighten with Wrench (7). There are 4 bolts in
total.
Step 6: Assemble front legs to Stretcher (E) using Screws (5). Tighten screws with screwdriver. The
front legs are marked Left & Right.
Step 7: After making sure all bolts are attached and hand tightened, turn the chair over.
INSTRUCTION SHEET
932/994/995/996-634
MIKE'S SIDE CHAIR

Step 8: Level the chair following “Chair Leveling Instruction”. This is an additional assembly
instruction sheet found inside the carton.
Step 9: Make sure the chair is level and tighten all bolts completely using the wrench supplied.
Step 10: Take off plastic cover on upholstery seat.
Assembly is now complete.
Bolt 5/16"*3"
Bolt 5/16"*21/2"
2
3
14pcs
4pcs
Bolt 5/16"*11/2" 2pcs
Hardware Pack
Wrench 5/16"
Lock washer 5/16"
Flat washer 5/16"
7
6
510pcs
10pcs
1pc
Screw
44pcs
A