Universal Furniture EXPLORE HOME 637310B User manual

INSTRUCTION SHEET
637310B: 310-31R-31F
637320B: 320-32R-32F
Upholstered Bed 5/0 6/6
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Whole Headboard
1pc
B
Headboard panel
1pc
C
Bottom stretcher
1pc
D
Right pier post
1pc
E
Left pier post
1pc
F
Bed foot
2pcs
G
Footboard
1pc
H
Side rail
2pcs
I
Support legs
3cs
J
slat
3pcs
K
Hardware pack
1bag
L
Hardware pack
1bag
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Attach bottom stretcher(C) to right pier post(D) and left pier post(E) with phillip head
bolt(1),spring washer(2) and flat washer(3) using wrench(4) ,then attach headboard(B) to
right pier post(D) and left pier post(E) with phillip head bolt(1),spring washer(2) and flat
washer(3) using wrench(4) from hardware pack(K), tighten all bolts. Also attach the bed foot
(F) to the footboard (G) by hand.
Step 3: Attach side rails(H) to whole headboard(A) and footboard(G) with nut (6),spring washer (7)
and bolts (10) using wrench(9). tighten all bolts.
Step 4: Screw slats onto side rails with screw by screwdriver (not provided). There are three slats,
please distribute each space evenly. Then adjust height of center support legs with screw
adjustment.
Note: 637320-32R-32F has 6 pcs support legs.
Assembly is now complete.

INSTRUCTION SHEET
637310B: 310-31R-31F
637320B: 320-32R-32F
Upholstered Bed 5/0 6/6
PHILLIP
HEAD BOLT
FLAT
WASHER
WRENCH
DOWE L
Q'TY
8PCS
8PCS
8PCS
1PC
4PCS
5/16"*2
5/16"
5/16"*19MM
87*19*2.5MM
10*40MM
1
2
3
4
5
Q'TY
5/16"
5/16"
5/16"L32
87*19*2.5MM
5/16"*3"
#8*1-1/4"
8PCS
8PCS
8PCS
8PCS
1PC
6PCS
6
7
8
9
10
11
SPRING
WASHER SPRING
WASHER
WRENCH
CURVED
WASHER
BOLT
SCREW
NUT
HARDWARE PACK (K) HARDWARE PACK (L)
Step 2
B
E
C
D
F
G
4
1
23
23
1
4

INSTRUCTION SHEET
637310B: 310-31R-31F
637320B: 320-32R-32F
Upholstered Bed 5/0 6/6
10
8
76
HI
J
11
9
Step 3