Universal Tool UT8962-17 User manual

UT8962-17
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour time-
weighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per square
inch gauge pressure (90 PSIG) maximum,
at the tool. Use of higher air pressure
can, and may cause injury. Also, the use
of higher air pressure places the internal
components under loads and stresses
they were not designed for, causing
premature failure. The air supply should
be clean and dry, preferably lubricated.
For best results, drain the moisture from
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
Safety Instructions
The following instructions are furnished as
general guidelines for use of your pneu-
matic tool. They cannot comprehensively
cover all possible or conceivable uses of
the subject tool. For additional information
on the safe use of air tools, we advise you
to obtain a copy of ANSI B186.1 Safety
Code for Portable Air Tools, available from
the following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the following
instructions, indicates that adherence to
the particular requirement is necessary to
conform to ANSI B186.1.
Tool Application and Usage
Portable tools shall be used only for the
purposes intended in their design and
within the capacity for which they were
intended and rated. It shall be the tool
owner’s and/or employer’s responsibility to
instruct each operator in the safe use of
the tool. Tools shall not be used without
guards and safety devices as furnished by
the manufacturer. Where an air tool is
modified or altered, the modifier shall
provide the safeguards to enable it to be
safely used in the operations intended and to
comply with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit air
pressure to the rated pressure where the
supply pressure exceeds the tool’s rated
pressure. Air hoses and lines shall be
relieved of compressed air before being
disconnected or disjointed, unless there is
automatic valve closing protection at the joint
being separated. Synthetic lubricants which
can cause deterioration of elastomer seals
shall not be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or employer’s
responsibility to assure that tools are
maintained in a safe operating condition. Tool
maintenance and repair shall be performed by
authorized, trained, competent personnel.
Tools shall be disconnected from their
compressed air supply before repairs are
attempted. Repairs shall be consistent with
the manufacturer’s recommended proce-
dures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation. It
shall be the tool owner’s and/or employer’s
responsibility to keep required rating
markings and warnings on the tool in legible
condition.
FPMC
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks, cement
and other masonry products
•Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
Description
Universal Tool 1/4” QC screwdriver has an ergonimc handle design for reduced
operator fatigue. Features a variable speed trigger and reverse for controlled
operation. Ideal for general assembly and maintenance operation. The user now
has the option of push to start operation by keeping the trigger depressed, or trigger
start operation by depressing the trigger after the tool has been held against the
fastener. Rotation of the fastener stops when the clutch reaches the set torque.
Removing the tool from the fastener or releasing the trigger will reset the tool for the
next cycle
PUSH TO START
AUTO SHUTOFF SCREWDRIVER

Ref. Part # Description Ref. Part # Description
Replacement Parts for UT8962-17
UT8962-17 UT8962-17
PUSH TO START
AUTO SHUTOFF SCREWDRIVER
Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by
someone other than Universal Tool or its authorized service centers. If a Universal Tool proves defective in
material of workmanship within one year after purchase, return it to any authorized service center or to Universal
Tool, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a brief
description of the defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairs
or replacements are warranted as described above for the remainder of the warranty period. Universal Tool's sole
liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential
or special damages, or any other damages, costs or expense of repair or replacement as described above.
Drive size .. ..........................................1/4" QC
Free speed (No load)......................1700 RPM
Torque (green spring) ....................5-19 in/lbs.
Torque (black spring) .................. 10-38 in/lbs.
Torque (yellow spring) ................. 15-45 in/lbs.
Weight .... ..............................................1.5 lbs.
Overall length .... ......................................8.65"
Average air consumption ......................4 CFM
Recommended hose size . ...................3/8" I.D.
Air inlet . ..............................................1/4" NPT
Maximum operating pressure ........ .........90 psi
PUSH TO START
AUTO SHUTOFF SCREWDRIVER
Clutch Adjustment
Clutches are adjusted through the slot
provided in the clutch housing. The slot
cover must be rotated to expose the
adjustment slot. Rotate (fig.58) the
clutch housing until the hole in the
adjustment nut is visible. Insert a No.1
Phillips screwdriver and rotate in a
clockwise direction to increase torque
setting or in a counter clockwise
direction to decrease the setting. After
each adjustment, the slot cover should
be rotated back to its locked posistion
1 9AS00501 MOTOR HOUSING
2 961249 PIN
3 9AS00503 AIR INLET
4 9AS00510 SHUT-OFF VALVE
5 9AS00509 SHUT-OFF VALVE SEAT
6 9AS00530 REVERSE VALVE
7 9706107 O-RING (2)
8 9AS00508 SHUT-OFF VALVE SPRING
9 9OR02500100 O-RING
10 9AS00521 REVERSING VALVE KNOB
11 9000070 SPRING PIN (1.6X10)
13 9000022 BALL BEARING (R3-ZZ) (2)
14 9000023 END PLATE
15 9AS00415 ROTOR
16 9000025 ROTOR BLADE (4)
17 9000026 SPRING PIN (1.5X6L)
18 9000027 CYLINDER
19 9000028 FRONT END PLATE
20 9AS00420 MOTOR SPACER
21 9AS20534 PUSH NEEDLE
22 9AS00422 INTERNAL GEAR
23 9AS00423 PLANET GEAR (3)
24 9AS00424 PIN (3/32"X18.8) (3)
26 9AS00426 WORK SPINDLE
30 9000039 BALL BEARING (77R6ZZ)
31 9AS00560 CLAMP NUT
32 9AS00550 MUFFLER MATERIAL
33 9AS00507 EXHAUST DIFFUSER
34 9000073 STEEL BALL (1/8”)
35 9000044 CLUTCH
36 9000045 PIN (1/8"X9.6)
37 9000046 RESET PIN
38 9000047 PIN (1/16"X11)
39 9000048 TRIP SLIDE
40 9000049 SPRING
41 9000050 PLUG
42 9000051 INTERNAL RING (RTW-22)
43 9000052 STEEL BALL (3/16") (4)
44 9000053 SPRING
45 9000054 CAM SPINDLE
46 9000055 COVER
47 9000056 BUSHING
48 9000057 C-RING (5103-43)
49 9000058 SPRING (Yellow)
49 9AS000149-12 SPRING (Black)
49 9AS000149-13 SPRING (Green)
50 9000059 THRUST RACE (TRA-815) (2)
51 9000060 ROLLER THRUST BEARING
52 9000061 ADJUSTMENT LOCK RING
53 9000062 ADJUSTMENT NUT
54 9000063 SPINDLE BUSHING
55 9000064 BALL RETAINER
56 9000065 SPRING
57 9000066 WASHER
58 9000067 ADJUSTMENT COVER
59 9AS00559 CLUTCH HOUSING
60 9000069 RETAINING RING(ISTW-11)
61 9000097 SPRING
62 9000071 RETAINER RING
63 9000072 STEEL BALL (3/32") (13)
64 9AS00552 RUBBER GRIP
65 9AS00562 HOOK
66 9AS000163 SCREWDRIVER
67 952235 O-RING
* Optional Part