Universal Tool UT8963AT-17 User manual

UT8963AT-17
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour time-
weighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per square
inch gauge pressure (90 PSIG) maximum,
at the tool. Use of higher air pressure
can, and may cause injury. Also, the use
of higher air pressure places the internal
components under loads and stresses
they were not designed for, causing
premature failure. The air supply should
be clean and dry, preferably lubricated.
For best results, drain the moisture from
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
FPMC
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
vLead from lead-based paints
vCrystalline silica from bricks, cement
and other masonry products
vArsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
Description
Universal Tool 1/4” QC screwdriver has an ergonimc handle design for reduced
operator fatigue. Features a variable speed trigger and reverse for controlled
operation. Ideal for general assembly and maintenance operation. The user now
has the option of push to start operation by keeping the trigger depressed, or trigger
start operation by depressing the trigger after the tool has been held against the
fastener. Rotation of the fastener stops when the clutch reaches the set torque.
Removing the tool from the fastener or releasing the trigger will reset the tool for the
next cycle
PUSH TO START
AUTO SHUTOFF SCREWDRIVER
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated.It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
devices as furnished by the manufac-
turer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in CAGI B186.1-2009.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protec-
tion at the joint being separated.Syn-
thetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply bef ore repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended proce-
dures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
Safety Instructions
The following instructions are furnished
as general guidelines for use of your
pneumatic tool. They cannot compre-
hensively cover all possible or conceiv-
able uses of the subject tool. For
additional information on the safe use
of air tools, we advise you to obtain a
copy of CAGI B186.1-2009 Safety
Code for Portable Air tools from the
following source:
COMPRESSED AIR AND GAS
INSTITUTE
1300 Sumner Avenue Cleveland,
OH 44115-2851 PH: [phone]
www.cagi.org
Or from Florida Pneumatic MFG Corp
851 Jupiter Park Lane Jupiter, FL
33458 PH: [phone]
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular require-
ment is necessary to conform to CAGI
B186.1-2009.

UT8963AT-17
PUSH TO START
AUTO SHUTOFF SCREWDRIVER
Parts Breakdown for UT8963AT-17
USE ONLY IMPACT SOCKETS & ACCESSORIES
Sockets and accessories used shall be of the impact socket type. Always check sockets,
retainers and drives regularly for wear or damage and replace whenever necessary
Drive size .. ..........................................1/4" QC
Free speed (No load)........................1700 RPM
Torque (green spring) ....................5-19 in/lbs.
Torque (black spring) .................. 10-38 in/lbs.
Torque (yellow spring)................. 15-45 in/lbs.
Weight .. ..............................................1.98 lbs.
Overall length ..........................................8.65"
Average air consumption ......................4 CFM
Recommended hose size . ...................3/8" I.D.
Air inlet . ..............................................1/4" NPT
Maximum operating pressure .................90 psi
Clutch Adjustment
Clutches are adjusted through the slot
provided in the clutch housing. The slot
cover must be rotated to expose the
adjustment slot. Rotate (fig.58) the
clutch housing until the hole in the
adjustment nut is visible. Insert a No.1
Phillips screwdriver and rotate in a
clockwise direction to increase torque
setting or in a counter clockwise
direction to decrease the setting. After
each adjustment, the slot cover should
be rotated back to its locked posistion
Ref. Description Part # Ref. Description Part #
Replacement Parts for UT8963AT-17
Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by
someone other than Universal Tool or its authorized service centers. If a Universal Tool proves defective in
material of workmanship within one year after purchase, return it to any authorized service center or to Universal
Tool, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a brief
description of the defect. Universal Tool will, at its option, repair or replace defective tools, free of charge. Repairs
or replacements are warranted as described above for the remainder of the warranty period. Universal Tool's sole
liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential
or special damages, or any other damages, costs or expense of repair or replacement as described above.
UT8963AT-17
PUSH TO START
AUTO SHUTOFF SCREWDRIVER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Motor Housing
Spring Pin
Air Inlet
Trigger
Valve Stem
Valve Bushing
Retaining Ring
Valve Spring
O-Ring
Valve Stem
Valve Bushing
Shut-off Valve Bushing
Ball Bearing (2)
End Plate
Rotor
Rotor Blades (4)
Spring Pin
Cylinder
Front End Plate
Motor Spacer
Push Needle
Internal Gear
Planet Gear (3)
Pin (3)
Work Spindle
Ball Bearing
Inlet Noose
Reverse Valve
O-Ring
O-Ring (2)
Clutch
Pin
Reset Pin
Pin
Trip Slide
Spring
Plug
Internal Ring
Steel Ball (4)
Spring
Cam Spindle
9AS00401
920448
9AS00503
9AS00404
9AS00405
9AS00406
9AS00447
9AS00408
9516114
9AS00410
9AS00411
9AS00412
9000022
9000023
9AS00415
9000025
9000026
9000027
9000028
9AS00420
9AS20234
9AS00422
9AS00423
9AS00424
9AS00426
9000039
9000040
9000041
9000042
9000043
9000044
9000045
9000046
9000047
9000048
9000049
9000050
9000051
9000052
9000053
9000054
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
70
71
72
73
74
77
78
79
80
81
82
83
84
85
86
87
88
90
Cover
Bushing
C-Ring
Spring
Thrust Race (2)
Roller Thrust Bearing
Adjustment Lock Ring
Adjustment Nut
Spindle Bushing
Ball Retainer
Spring
Washer
Adjustment Cover
Clutch Housing
Retaining Ring
Spring Pin
Retainer Ring
Steel Ball (13)
Steel Ball
Rubber Grip
Shut-off Valve Seat
Shut-off Valve
Shut-off Valve Spring
Valve Cap (2)
Reversing Valve Knob
Reversing Knob Spacer
Screw
Ring
Damping Material
Exhaust Diffuser
Air Inlet
Set Screw
Hex. Wrench
Spring
Screwdriver
O-Ring
O-Ring
Shut-off Valve Seat
O-Ring
O-Ring (3)
O-Ring
9000055
9000056
9000057
9000058
9000059
9000060
9000061
9000062
9000063
9000064
9000065
9000066
9000067
9000068
9000069
9000070
9000071
9000072
9000073
9AS00452
9AS00509
9AS00510
9AS00508
9AS00409
9AS00421
9AS00433
9AS00432
9000083
9000086
9AS00407
9AS00403
910213
910020
9000097
9AS000163
952235
9OR00200100
9AS00427
9OR01007105
9AS000109
9OR02000100