urban ambiance UQL1160 User manual

Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
1of7
Part Description Quantity
A Crossbar
Nipple
1pc.
2 pcs.
2 pcs.
1pc.
1pc.
B
C
D
E
Hex Nut
Package Contents
Canopy Chain Loop
Lock Washer
A
B
C
D
F
E
1pc.
FCanopy Lock Ring
I
J
G
H
1pc.
1pc.
1pc.
1pc.
G
H
I
J
Fixture Chain
Ceiling Canopy
Fixture Loop Assembly
Fixture Body
K
3 pcs.
KCandle Cover
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire
Tools Required:
strippers, electrical tape, safety glasses.
Light Source: (3) Candelabra Base 60W Maximum
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Installation Instructions: UQL1160
www.urbanambiance.com

2of7
12.5” Dia.
Overall Height 118”
(Includes 96” Chain)
21”
1
1”
5” Dia.
GND
2.4 m m 13 Ga
QUIOZEL
UQL1160
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART REQ.
NO.
1 UQL1160CC CANDLE COVER 3
(3)60W Candelabra
base bulbs
(not Supplied)
2

3of7
STEP 2 -Attach Crossbar to Outlet Box
A. Secure the Corssbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
Outlet Box
Screw (not
Supplied)
Figure 2
Crossbar
Outlet Box
Mounting
Hole
Figure 3
STEP 3 Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
Nipple
Crossbar
Lock Washer
Hex Nut
STEP 1 -Attach Fixture Loop Assembly to
Fixture Body
A. Thread the Fixture Loop Assembly (I) onto the
J . Hand tighten until snug.
top
center of the Fixture Body ( )
Figure 1
Fixture Loop
Fixture Body
Installation Instructions: UQL1160
www.urbanambiance.com

4of7
STEP 4 -Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (E) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (E) and hand tighten until snug.
Figure 4
Outlet Box
STEP 5 Assemble Ceiling Canopy-
A. Push the Ceiling Canopy (H) upward over the Outlet
Box. Thread the Canopy Lock Ring (F) onto the Canopy
Chain Loop (E) and tighten until snug to secure the
Ceiling Canopy (H).
Crossbar
Ceiling Canopy
Hex Nut
Nipple
Figure 5
Canopy Chian Loop
Outlet Box
Lock Washer
Canopy
Chain Loop
Canopy
Lock Ring
Installation Instructions: UQL1160
www.urbanambiance.com

5of7
Figure 7
STEP 7 Pass Supply Wires through Fixture
Chain
-
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (G) alternating links. Push the wires up
through the Canopy Chain Loop (E) into the outlet box.
Figure 6
STEP 6 Attach Fixture Chain to Canopy
Chain Loop and Fixture Loop
-
A. Adjust the Fixture Chain (G) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (G) onto the
Canopy Chain Loop (E) and then attach the other end of
the Fixture Chain (G) onto the Fixture Loop (I) on the
top of the fixture.
Fixture Loop
Fixture Chain
Supply Wire and
Ground Wire
Supply Wire
and Ground Wire
Fixture Chain
Canopy Chain Loop
Canopy Chain
Loop
Installation Instructions: UQL1160
www.urbanambiance.com

6of7
Figure 9
STEP 8 -Make Wire Connections
A. Un-thread the Canopy Lock Ring (F) and slide Canopy Lock
Ring (F) and Ceiling Canopy (H) down the Fixture Chain (G).
B. Push all slack fixture wire through Canopy Chain Loop (E)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare
wire ends according to instructions supplied with connectors.
D. Connect White Supply Wire from the Outlet Box to Ribbed
Side Wire from fixture.
E. Connect Black (or Red) Supply Wire from the Outlet Box to
Smooth Side Wire from fixture.
F. Connect Ground Wire from the Outlet Box to Ground Wire
from fixture.
G. Twist connectors until wires are tightly joined together.
H. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
G. Re-attach the Ceiling Canopy (H) as shown in Step 5.
Figure 8
White wire from supply Ribbed side wire
from fixture
Black wire from supply
(or Red)
Smooth side wire
from fixture
Ground wire from supply Ground wire from fixture
Figure 10
STEP 9 Attach Candle Cover to Socket
Assembly
-
A. Place the Candle Cover (K) over the Socket properly.
Socket
Candle
Cover
Canopy Chain
Loop
Fixture Chain
Supply Wire and
Ground Wire
Supply Wire and
Ground Wire from
Outlet Box
Ceiling Canopy
Canopy Lock Ring
Installation Instructions: UQL1160
www.urbanambiance.com

7of7
Figure 11
STEP 10 -Install Bulb
A. standard bulb with a candelabra screw
base 0
This fixture uses
. Maximum 6 watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Socket
Bulb
Installation Instructions: UQL1160
www.urbanambiance.com