urban ambiance UQL1123 User manual

Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Figure 4
A
Fixture
Body
x1
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
EstimatedAssemblyTime:30-45minutes
Preparation:Identify andinspect allparts beforebeginning installation.Check packagecontent listand diagramsbelow tobe sureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
Fixturecan onlybe mountedin thedirection indicatedon page2.
BulbRecommended: (3) CandelabraBaseT8Bulb 40W(supplied), 60W Maximum.
STEP 1 Install Inner Backplate-
A. Pass the supply wires through the Crossbar Assembly (I). Attach the
Crossbar Assembly (I) to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included). Tighten until snug.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture Figure 3
H
Crossbar
Assembly
x1
Supply Wires with
Ground Wire
H
Outlet Box Screws
(not included)
Outlet Box
Figure 1
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (A) over
the outlet box. Align the holes in the
backplate with the mounting
screws. Place caulk (not supplied)
into the previously removed
mounting balls and then attach
Fixture Body (A) using the mounting
balls. Hand tighten until snug.
Figure 2
Hex Nut and
Lock Washer
H
Mounting
Ball
Mounting
Screw
A
B
Candle
Cover
x3
CBulb
x3
DShade
x1
ECage
x1
F
Mounting
Ball
x2
G
Water Proof
Washer
x2
STEP 2 Fit Fixture Body to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (H). Fit the
Fixture Body (A) Crossbar Assembly (H) and secure with mounting
balls. Note: The backplate of the Fixture Body (A) should be snug
against the wall surface and the mounting balls. If not, adjust the
length of the nipple on the Crossbar Assembly (H) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate of the Fixture Body (A) is secure,
remove the mounting ball and Fixture Body (A) and proceed to Step 3.
H
Mounting
Ball
Mounting
Screw
A
STEP 5 Install Candle Cover
and Bulb
-
A. Place Candle Cover (B) over the
Socket properly.
B. This fixture uses candelabra
bulb with standard screw base.
Maximum 60 watts.
C. Insert bulb and screw snugly into
place.
B
C
Socket
Figure 5
Installation Instructions: UQL1123
www.urbanambiance.com

2of2
Figure 6
Figure 8
STEP 8 -Apply Silicone
Sealer
A. Make sure exterior wall
surface and fixture
backplate are free of dirt
before applying caulk.
Using exterior grade caulk,
caulk over top of backplate
and down other side. Do
not caulk bottom of fixture
backplate to ensure proper
moisture drainage.
Your fixture is now
assembled and ready to
use. Enjoy!
Exterior
Grade
Caulk
Backplate
MRE8410WT
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION REQ.
NO.
1
FINISH: WESTERN BRONZE
Fixture can only be
mounted in the
direction indicated
(3) 40W
T8 Bulbs
(Supplied),
6
Maximum 0W.
Candelabra
Base
A
D
STEP 6 Attach Shade to Fixture
Body
-
A. Thread Shade (D) to Fixture Body
(A), hand tighten until sung.
Figure 7
E
STEP 7 Attach Cage to Fixture
Body
-
A. Pass the Bolt on the top of Cage
(E) through the hole on the
Fixture Hood, place Water Proof
Washer (G) over the Bolt, secure
by threading Mounting Ball (F)
onto the Bolt, hand tighten until
sung.
G
F
Bolt
11.5”
13.5”
20”
7.5”Dia.
10.5”Dia. 4.5”
9”
UQL1123SH GLASS 1
1
2VINTAGE BULB T8-40W 3
www.urbanambiance.com
UQL1123BU