urban ambiance UQL1249 User manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (2)A19 Medium Base Bulbs 60W Maximum,Alternate Bulbs (2)13W CFLMaximum.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
1of2
Package Contents
B
Crossbar
x1
Lock Washer
x1
Hex Nut
x1
Nipple
x1
A
FFixture Body
x1
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
C
D
Knob
x1
E
GGlass Panel
x1
STEP 1 Remove Cage-
A. Remove Cage from the
Ceiling Canopy by unlocking
Lock Balls.
Ceiling
Canopy
Lock Ball
Cage
Figure 1
STEP 2 Install Crossbar-
A. A)Attach the Crossbar ( to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included) Tighten until snug..
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw A
Figure 2
A
B
C
D
E
STEP 3 Install Nipple and Ceiling
Canopy
-
*Pliers is required for this step.
A. Thread Hex Nut (C) to the middle of
the Nipple (D). Place Lock Washer (B)
over the Nipple (D) and then thread
the Nipple (D) into the Crossbar (A)
until the Nipple (D) is about 0.375”
above the Crossbar (A).
C. Place the Ceiling Canopy over the
Nipple (D) against the ceiling to
Ceiling
Canopy
(Step 3 Continued)
determine the correct position of the Nipple (D). Thread the Knob
(E) onto the Nipple (D). Adjust the Nipple (D) to allow the Ceiling
Canopy to rest against the ceiling when held in place by the Knob
(E).
D. Remove the Knob (E) and the Ceiling Canopy. Tighten the Hex Nut
(C) against the Crossbar (A) to secure in place.
E. Refer to Step 4 for wire connections.
F. Place the Ceiling Canopy back over the Nipple (D) and secure with
the Knob (E). Hand tighten until snug.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 - Install Bulbs and Cage
A. Place the Glass Panel (G) into the bottom of the Cage (G) properly.
B. This fixture uses standard bulbs with standard screw bases.
Maximum 60 watts.
C. Attach the Cage over the Bolts on the bottom of the Ceiling Canopy
Insert bulb and screw snugly into place.
Socket
Figure 5
Bolt
G
Cage
Lock
Ball
Ceiling
Canopy
and secure with Lock
Balls. Hand tighten until
snug.
Your fixture is now
assembled and ready to
use. Enjoy!
Installation Instructions: UQL1249
www.urbanambiance.com

2of2
HOW TO REPLACE GLASS PANELS
Unlock Lock Balls and remove the Cage from the Ceiling Canopy.
A Replace the
Glass Panel with the replacement directly.
. Replace the Glass Panel on the bottom of the Cage:
B. Replace Side Glass Panels: Unscrew Screws on the top edge of the
Figure 6
Ceiling
Canopy
Bolt
Screw
Side Glass
Panel
Cage
Lock Ball
Glass
Panel
Cage and remove Glass
Holder. Replace the Side
Glass Panel with the
replacement. Place the
Shade Holder back onto
the Cage and secure with
the removed
Screws. Hand tighten
until snug.
Once the Glass Panel is
replaced and secured to
the Cage. Place the Cage
back onto the Ceiling
Canopy and secure with
Lock Balls. Hand tighten
until snug.
previously
SKU: UQL1249
(2) 60W
Bulb
(Not Supplied)
Medium
Base
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
PART NUMBER
1
NO. PART NUMBER REPLACEMENT PART REQ.
UQL1249PA 1
BOTTOM GLASS PANEL
2UQL1249PA 4
SIDE GLASS PANEL
12” SQ.
5.5”
2
1
www.urbanambiance.com