USX-MOUNT XMM009 User manual

XMM009
INSTRUCTION MANUAL
For 32-65" TV
If you have any questions along the way, just give us a call
1-800-460-0956 or mail to [email protected].
We’re ready to help!

Before getting started, let’s check below lists to make sure it is just right for you!
2
3
4
5
2
Does your TV
(including accessories)
weigh MORE than
77 lbs. (35 kg)?
What is your
wall made of?
Do you have
all the tools
needed?
(NOT INCLUDE) Tape
Measure
CAUTION
Pencil Screw
driver
Electric
Drill
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
Drywall with
wood studs? CAUTION:
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
Solid concrete ?
1/2 in.
(13 mm)
Socket
Wrench
Stud
Finder
7/32 in.
(5.5 mm)
Wood
Drill Bit
● This product is designed for use in wood stud, solid concrete walls - DO NOT install into drywall alone
● The wall must be capable of supporting five times the weight of the TV and mount itself
● Do not use this product for any purpose not explicitly specified by manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Unsure?
Call Customer Service:
1-800-460-0956
3/8 in.
(10 mm)
Masonry
Drill Bit
Hammer
1
Check your TV
VESA is within
Min and Max size
No? This mount is NOT compatible.
Yes? Perfect !
MAX:400mm/15.74"
(MIN:75mm/2.95")
MAX:400mm/15.74"
(MIN:75mm/2.95")

TV INTERFACE 3-D
WALL PLATE
FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED SIDE VIEW - RETRACTED
TOP VIEW - EXTENDED SIDE VIEW - EXTENDED
3
382mm
[15.03in]
444mm
[17.48in]
444mm
[17.48in]
MAX:400mm
[15.75in]
MAX:400mm
[15.75in]
406mm
[16.00in]
236mm
[9.29in]
72mm
[2.83in]
+5°
-15°
MIN:75mm
[2.95in]
MIN:75mm
[2.95in]
+45° -45°

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts
are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
4
Allen Key
x1
M6x8mm Bolt
x4
M4x12mm
M6x12mm
M8x25mm
M4x30mm
M6x35mm
M8x50mm
Extended arms
x4
M6x17mm M8x22mm
M4 M6
10mm 2.5mm
Washers
Spacers
TV Screws
x4
x4
x4
x4
x4
x4
x4
x4 x4
x4 x8
x4

Parts and Hardware for STEP 2
1-1 Disassemble Wall Plate Unit into Two Pieces
5
Wall plate
TV plate
Lag Bolt M8 Washer
Concrete Wall Anchor 4pcs
CAUTION:Do not use in drywall or wood
x4 x4
Wall Plate Unit
x1
Level

6
1-2 Choose Configuration
①
②
③
④
① 75X75
② 100X100
③ 100X200
④ 200X100
⑤ 200X200
200X300 400X200
⑧
⑤
⑦
⑨
①
②
③
④
⑤
①
②
③
④
⑤
①
②
③
④
⑤
⑥ ⑥
⑥ ⑥
150X150
⑧
⑦
⑧
⑦
⑧
⑦
⑧
⑦200X400
⑨
⑩⑨⑩
⑨
⑩⑨⑩
300X200
⑩
⑥

1-3 Extended arms assembly options
7
400X400400X300
1 2
1 3
1 1 1 1
1 11 1
1 1
1 3
1 2
1 2
1 3 1 3
1 2
300X300
1 3
TV plate
TV plate
1 2

M8
M6
M4
TV back
Bracket Washer
Bracket Spacer
No, go to PAGE 9 for detailed combination.
Yes, go to PAGE 9 for detailed combination.
TV back
Short Screw
1-4 Select TV Screws 1-5 Need Spacer?
Washer
Long Screw
8

Tips: If you need to combine M8(c/f screw with 2.5mm spacer( j ), you have to remove the inner circle.
Screw(s) and washer(s)
Spacer(s), screw(s) and washer(s)
1-6 Attach the TV Plate
No!
9

CAUTION: Avoid potential personal injury or property damage!
● Drywall covering the wall, must not exceed 5/8 in. (16 mm)
● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using, a thin nail,
or an edge to edge stud finder.
2. Position the wall plate at your desired height and line up the holes with your stud center line. Level
the wall plate and mark the hole locations.
Centre line
Again, find another wood stud
● Minimum horizontal space between fasteners: 16 in. (406 mm)
10
16"
Wall plate

3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center
of the studs.
4. Install wall plate using four lag bolts and washers . Tighten the lag bolts only until they
are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
Go to STEP 3 on PAGE 14.
2.5"(64mm)
7/32"
(5.5mm)
11
16"
Wall plate

CAUTION: Avoid potential personal injury or property damage!
● Mount the wall plate assembly directly onto the concrete surface
● Minimum solid concrete thickness: 8 in. (203 mm)
1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the
hole locations.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).
2.5"(64mm)
3/8"
(10mm)
● Minimum horizontal space between fasteners: 16 in. (406 mm)
12
Wall plate

3. Insert four anchors .
CAUTION: Be sure the anchors are seated flush with the concrete surface.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
4. Insert wall plate using four lag bolts and washers .Tighten the lag bolts only until they are
pulled firmly against the wall plate.
Concrete Wall
Anchor
13
Wall plate

Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall
tightly.
77 LBS (35 KG)
14
Wall plate

TV
1 2
15

Loosen
Tighten
5-1 TV leveling adjustment (±4°):
Loosen 2 leveling bolts on the rear of TV plate by
maximum 2 turns, adjust to level, and retighten to secure.
16

5-2 Tilting angle adjustment (+5°/-15°)：
Loosen handle and tilting bolt, adjust TV to your desired position,
then tighten handle and tilting bolt.
-15°
+5°
Handle Tilting bolts
17