UWS TRANSFER TANK User manual

UWSTA.COM •NEED ASSISTANCE? •8 7 7. 2 8 7. 8 6 3 4 •RB •PAGE 1
Parts List*
1Transfer tank
2Key (only supplied with combo models)
1Filler neck and cap
1Drain plug, 3/8"
* Hardware not included. You must purchase
your own hardware to install this tool box.
INSTALLATION MANUAL
Level of Difficulty
Easy
Representative Product Photos (your specific tank may vary in style, size or finish)
TRANSFER
TANK
Maintenance
For polished, gloss and other smooth
finishes, polish may be used to clear
small scratches and scuffs on the finish.
Mild automotive detergent may be used to
clean the product. Do not use dish detergent,
abrasive cleaners, abrasive pads, wire
brushes or other similar products that
may damage the finish.
DANGER
Danger of explosion. Do not use this product for storing or transporting flammables,
explosives, hazardous materials or hazardous waste, such as containers of gasoline,
solvents, gun powder, dynamite, propane tanks, acetylene tanks and cutting torches.
This tank is DOT-compliant for transporting Class 3 combustible fuels only, such as diesel.
The tank is not approved for transportation of flammable fuels, such as gasoline, and should
never be connected to a vehicle's fuel system or used as an auxiliary fuel tank.
Leaking fuel system are a fire and explosion hazard.
WARNING
Never exceed the vehicle manufacturer's recommended capacity.
Before drilling into your truck bed, check under your vehicle to ensure the drill location does not
puncture, cut or obstruct any brake or fuel fluid lines, electrical wires, fuel tanks, etc. Precaution
must be taken that all fasteners near the fuel tank do not create the possibility of fuel tank
puncture or other damage during a collision.
This product can reduce the driver's ability to clearly see roadways, vehicular or pedestrian
traffic and other objects through the rear and side windows of the vehicle, which may cause
an accident. Extra precaution should be taken when driving a vehicle with this product.
Tank must be vented at all times. Remove vent cap with caution.
Must use automatic shut off nozzle (not provided).
Do not interfere with factory-installed safety equipment.
NOTICE
Do not pressurize tank.
Must use a fuel filter.
Tank to be lifted only when empty.
For private use only. Tank is not intended to be used commercially.
Tank does not meet the code of federal regulations title 49 (chapter iii [393.65, 363.67]).
Tank is not to be used as an auxiliary tank.
Tank must be securely bolted to bed of vehicle.
Tank not compatible with diesel exhaust fluid (DEF) or other corrosive materials.
Product Registration and Warranty
CURT Group stands behind our products
with industry-leading warranties. Provide
feedback and help us to improve our
products by registering your purchase at:
warranty.curtgroup.com/surveys
Tools Required
Drill Drill bit, 3/8"
Ratchet Socket set
Tape measure Marker
Torque Specifications*
Metric
M6 bolt 3 ft-lbs.
M8 bolt 7 ft-lbs.
M10 bolt 16 ft-lbs.
M12 bolt 28 ft-lbs.
SAE
1/4" bolt 3 ft-lbs.
5/16" bolt 7 ft-lbs.
3/8" bolt 16 ft-lbs.
7/16" bolt 20 ft-lbs.
1/2" bolt 28 ft-lbs.
* Above specifications are general guidelines.
If purchasing hardware use the torque
specifications provided with that hardware.

UWSTA.COM •NEED ASSISTANCE? •8 7 7. 2 8 7. 8 6 3 4 •RB •PAGE 2
Step 1
WARNING
Before drilling into your truck bed, check under
your vehicle to ensure the drill location does not
puncture, cut or obstruct any brake or fuel fluid
lines, electrical wires, fuel tanks, etc. Precaution
must be taken that all fasteners near the fuel
tank do not create the possibility of fuel tank
puncture or other damage during a collision
Push the tank up to the truck cab and center
it side-to-side. Make sure the tank is fully
supported by the truck bed floor.
Use the mounting brackets as a guide to mark
holes in the truck bed floor. Remove the tank
and drill 3/8" holes in the marked locations.
NOTICE
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To help prevent damage to the product or vehicle, refer to the torque specifications when securing hardware during the installation process.
Do not use this product for purposes other than those for which they were designed. Never modify this product.
Consult your dealer if you have any questions regarding the installation, operation, use and limits of this product.
Treat or seal all fasteners and exposed metal in any holes drilled in vehicle to prevent corrosion.
DANGER
Danger of explosion. Do not cut, weld or drill into the tank.
Doing so could result in serious injury or death.

UWSTA.COM •NEED ASSISTANCE? •8 7 7. 2 8 7. 8 6 3 4 •RB •PAGE 3
Step 2
Place the tank back in the bed of the truck
and align the drilled holes with the mounting
brackets. If any holes fall between the ribs on
the truck bed floor, spacers will be required
between the floor and mounting bracket for
proper installation.
Before securing to the bed of the truck ensure
the tank is level. Secure the mounting brackets
to the truck bed with a hex bolt, two flat washers,
one lock washer and one nut in each hole. Do
not over tighten the hardware.
Attach the filler neck and cap.
DANGER
Make sure the transfer tank and pump are
grounded to avoid static charge. Static build-up
can result in explosion.
Step 3
CAUTION
Ensure all knobs, bolts, screws, straps and
locks are firmly secured before every trip.
Periodically re-tighten and inspect all components
for signs of wear, corrosion and fatigue.
With the transfer tank installed, periodic
inspections should be performed to ensure
all mounting hardware remains tight.
To protect your investment, see the
'Maintenance' section on page 1.
Congratulations on the installation
of your new UWS transfer tank.
Nut
Lock washer
Flat washer
Flat washer
Truck bed
Tank mounting
bracket
Hex bolt