V-Tec AT16/C5 User manual

ENGLISH
VIDEO INTERCOM SYSTEM
AT16/C5-AT16 USER MANUAL
TALK MENU MONITOR
2
VERSION 1.0

●Slots or openings in the back of the monitor, are provided for
ventilation and to ensure reliable operation of the video monitor
or equipment and to protect if from overheating. These openings
must not be blocked or covered. The monitor should never be
placed near or over a radiator or heat register and should not be
placed in a built-in installation such as a bookcase unless proper
ventilation is provided.
●All parts should be protected from violence vibration. And not
allow be impacting, knocking and dropping.
●For clean the LCD screen, using hands or wet cloth is forbidden.
●Please do the cleanness with soft cotton cloth, please do not use the
organic or chemical clean impregnate. If necessary, please use pure
water or dilute soap water to clean the dust.
●Image distortion may occur if the video door phone is mounted
too close to magnetic field e. g. Microwaves, TV, computer etc.
●Please keep away the video door monitor from wet, high
temperature, dust, and caustic and oxidation gas in order to avoid
any unpredictable damage.
●Do NOT open the device in any condition, call the administrator
for help if there is any problem or mulfunction happens.
Precautions

Contents

The model you purchase maybe haven't all functions mentioned here, but
the functions contained in your product can be found in this manual.
1. Parts and Functions ....................................................................... 1
2. Basic Door Release Operation ...................................................... 2
3. Intercom Function ......................................................................... 2
4. Basic Setup Instructions ................................................................ 3
4.1 How to Enter Main Menu Page ............................................... 3
4.2 Ring Tone Settings ................................................................... 3
4.3 NO Disturb Mode .................................................................... 4
4.4 Date and Time Setting .............................................................. 4
4.5 Room Adress ............................................................................ 4
4.6 Restore to Default .................................................................... 5
5. Screen and Volume Adjustment .................................................... 5
6. Defense Alarm Operation(optional) .............................................. 6
7. Remote Control Function(optional) .............................................. 7
8. Specications ................................................................................ 8

1. Parts and Functions
1
Key Functions
1. Microphone ●
●Receives●sound●from●the●user.
2. LCD screen ●
●Display●the●images●from●outdoor●station.Touch●operation.
3. LED indicator ●
●Normally●light●on●when●power●on
●
●Flash●when●receiving●signal●or●activating●No●disturb●mode
4. Call key ●
●Press●to●activate●the●intercom●function●page.
5. Monitor key ●
●Press●to●view●the●outside●condiction.
6. Navigation key ●
●Scrolls●through●lists●and●moves●the●cursor●.●Also●adjust●the●ringer●
volume.
7. Unlock key ●
●Press●to●release●the●door●for●visitors●during●talking●or●monitoring.
8. Talk key ●
●Press●to●talk●with●the●visitors●while●receiving●a●call.
9. Menu key ●
●Press●to●open●a●list●of●actions●available●on●the●current●screen.
10. Speaker ●
●Output●sound●from●the●outdoor.
11. Mounting Hook ●
●Used●to●hang●up●the●monitor●unit
12. Connection Port ●
●Bus●line●terminal
1
2
3
4
5
6
7
8
9
10
11
12
AT16 hasn’t this
terminal.
AT16 or C5-AT16 back view
TALK MENU MONITOR
2

2. Basic Door Release Operation
3. Intercom Function
1. Input room numbers in Door Station of
the building or main entrance, the Monitor
rings, at the same time, the screen displays
the visitor image.
2. Press TALK Button on monitor, you can
talk with the visitor for 70 seconds. During
communication, press TALK Button again
to end the conversation. If nobody answers
the phone, the screen will be turned off
automatically after 40 seconds.
3. During calling or talking state, Press
UNLOCK Button to open the door for the
visitor.
4. When the monitor is in standby mode, press
MONITOR Button, you can see the outside
view.During monitoring,pressing UNLOCK
Button can open the door.Press MONITOR
Button again to close the screen.
When the monitor is in standby mode, press CALL
Button to enter Intercom Function page. (or select
item on main menu page). Use ▲ / ▼ Button to
move upward / downward to select the item you want,
press MENU Button to call.
Intercom Function
Call Guard Unit
Direct Call Guard Unit
Intercom Call
Exit
1. Choose Call Guard Unit item will sent a call
message to the guard center and wait for calling
back.
2. Choose Direct Call Guard Unit will dail the guard
center immediately.
2

3. Intercom Call: you can call the other users in the
same network with you. Input the building code and
room number by using ▲ / ▼ Button to increase /
decrease the value; use Button to select next digit;
After finish, press Talk Button to active the calling,
a call message will be sent out, if the system is free,
you will heard the feedback rings, you can talk with
someone who answers the call.Press Button to
return Intercom Function page.
4. Basic Setup Instructions
4.1 How to Enter Main Menu Page
4.2 Ring Tone Settings
1. Press MENU Button in standby mode, the date/time page will be showed. (the
date/time page will be closed in 3 minutes if no operation)
2. Press MENU Button again, main menu page will be showed.
Select
setup
item on main menu page to enter setup page.There are 12 pieces ring tones
can be selected.use / Button to select last/next ring tone,it will perform
immediatelly.
Door Station Tone
:set the ring tone calling from
outdoor station.
Door Bell Tone
:set the ring tone calling from door bell.
Guard Unit Tone
:set the ring tone calling from guard
unit.
Door Station Tone -- 01
Door Bell Tone -- 05
GuardUnit Tone -- 05
No Disturb Mode -- off
Installation...
Exit
3

4.3 NO Disturb Mode
4.4 Date and Time Setting
1. Select
setup
item on main menu page to enter setup
page,then use ▲ / ▼ button to select Installation...
item. A password will be asked before enter next
sub menu.the password is 2412, Input the password
by using ▲ / ▼ Button to increase / decrease the
value; use Button to select next digit, and press
button to return last page. After finish,press MENU
Button to confirm and enter the sub menu page.
2. Select Date and Time Set... item. Input date and
time by pressing the ▲ / ▼ Button to increase /
decrease the value and pressing Button to select
next digit,After finish,press MENU Button to save
and exit.and press button to exit and unsave.
If you don't want to be disturbed (for example, at night), set this item is on(use /
button to choose on/off), any call from the outdoor station will be sent to the guard
center, and the guard person will tell the visitor that you do not want to accept the visit.
Time
Date
2010 03 31
1 0 3 2
:
Alarm In/Out Delay -- 40
Date And Time Set ...
Room Address...
Other Settings...
Information...
Exit
4
4.5 Room Adress
Room adress is the number you input on door station
to call the user.
According to 4.4 , select Room Adress... item, 4 digits
number are required for room adress.Input the number
by pressing ▲ / ▼ Button to increase / decrease the
value; use Button to select next digit.After finish,press
MENU Button to save and exit.and press button to
exit and unsave.
Room
6666

5. Screen and Volume Adjustment
During monitoring or talking, press MENU Button,the
ADJUST MENU
will be displayed.
Use ▲ / ▼ Button to select the adjustment item; use / Button to decrease / increase
the value.
ＲＧＢ
５
４
２
６
scene
user
Brightness
Colour
Ring Volume
Talk Volume
1. The first item is Scene mode selection: Total 4
screen modes can be selected in sequence:
Normal,
User, Soft
and
Bright.
Note that only at
User mode
that you can modify
Brightness
or
colour.
whenever
you modify
Brightness
or
colour
item
,
the
Scene
mode
item will be set to
User
mode automatically.
2. The
Brightness
and
Colour
item is for the image
quality setting, adjust the value to get the best image you like.
3. The
Ring Volume
and
Talk Volume
items are ring tone and talking volume adjustment.
4. Note that all the modifications will be done immediately after the operation. Press
"MENU" button to quit the adjust page.
5
4.6 Restore to Default
According to 4.4 , select Information... item, this item
will show the
hardware/software
version and voltage
information of the Monitor. Select Restore to default
item ,then press MENU button. All settings will be
restored to default.(Note that the restore to default
operation will not change the time setting and the datas.)
Hardware Ver. A1.2
Software Ver. V8.9
Voltage 25.6
Manufacture AT16
Restore to default
Exit

6. Defense Alarm Operation(optional)
This system have auto-alarm function to ensure the security for the house owner. Total
4 different sensors were placed to protect different defense area. When the sensor was
triggered, the monitor will sent out alarm sound immediately and will sent the alarm signal
to the guard center at the same time. Note that your system may not have all the 4 sensors
according to the system configuration.
Motion Sensor
Delay sensor, normally it will be
placed on doors or windows.
If the sensor is set, when the
door or window is opened,
the monitor will sent out alarm
sound and sent the alarm signal
to the guard center.
Smoke Sensor
24-hour sensor, this sensor
is opened by the system by
default. It can be placed on
living room or kitchens. if any
fire happened in the area, the
monitor will sent out alarm
sound and sent the alarm signal
to the guard center.
Infrared Sensor
Delay sensor, can be placed on
living room or bedrooms. When the
sensor is set, if some body invade
into the defence area, the monitor
will sent out alarm sound and
sent the alarm signal to the guard
center. You can set this sensor when
nobody at home.
Emergency Help Button
24-hour sensor, this sensor is
opened by the system by default.
It can be placed any where
suitable. if any fire happened in
the area, the monitor will sent
out the emergency help signal to
the guard center.
1. Select item on main menu page to enter alarm
function page as show on the right.
2. Use ▲ / ▼ Button to select, press MENU Button to
confirm. If the current state is Armed, the 'Disarm'
icon is selectable, and vice versa.
6

7. Remote Control Function(optional)
According to 4.4 , select Other Settings... item . A add/
del remote page will be showed. this item is for adding
and deleting Remote function.
1. Add Remote
2. Del Remote
3. Exit
3.
Out-Delay Period:
after you arm the system, you
will get into Out Delay Period, monitor will
sent out short “Di” every 3 seconds; you
will hear a long “Di~” at the end of the Out
Delay Period, and the system is gotten into the
protecting status. By default, the Out Delay
Period is 40 seconds, users must get out off the
room within 40 seconds, otherwise the system will treat the user as a invader and sent out
the alarm signal.
4.
In-Delay Period:
When the system is armed, the defence alarm are activated, to disarm
the alarms. When you come into the room, you have 40 seconds to deactivate the
sensors(by enter MAIN --> ALARM menu, select Disarm item); if you didn’t
deactivate the sensors after 40 seconds, the monitor will sent out alarm sound and sent
the alarm signal to the Guard Unit.
5. 40 seconds is the default setting for in-out delay time, it can be changed by the
administrator.
D A
B C
[A] Button: Work as Emergency Help Button, press
and hold this button for 3s, the monitor will sent out the
emergency help signal to the guard center.
[B] Button: Arm button, press and hold this button for
1s will arm the system(same result as enter MAIN -->
ALARM menu, select Arm item).
[C] Button: Disarm button, press and hold this button
for 1s will disarm the system(same result as enter MAIN
--> ALARM menu, select Disarm item).
[D] Button: Use this button to release the door.(same
result as press the Unlock button on monitor).
7

8. Specications
1. Remote control distance is normally up to 30 meters, and will extend if the built-in
telescopic antenna is taken out.
2. If the controlled distance is becoming shorter, or LED doesn't light on while pressing
any button, open the remote control unit and replace the battery with a new one.
NOTE:
●
●Power●supply●for●indoor●monitor:●● ● DC●15~18V●(supplied●by●system)
●
●Power●consumption:● ●● Standby●1W;●Working●status●5W
●
●Monitor●screen:● ● 3.5●Inch●color●LCD
●
●Display●Resolutions:● ● 320(R,●G,●B)●x●240●pixels
●
●Video●signal:● ● 1Vp-p,●75Ω,●CCIR●standard
●
●Wiring:● ● CAT5●cable,●polarity
●
●Dimensions:● ● 220(H)×105(W)×20(D)mm
8

Please read this manual carefully before using the product you purchase, and keep it
well for future use.We reserve the right to modify the specification in this manual at
any time without notice.
VERSION 1.0