V-Tec Livila VT27 User manual

VT27 USER MANUAL(EN)
4 Wire Video Intercom System
Read this manual carefully before using the product, and keep it well for future use.

1
2
3
4

1. Parts and Functions
1
2
3
4
Indicator 1
Digital TFT LCD Screen
UNLOCK Button
TALK/MON Button
MENU Button
Microphone
Speaker
Connection Port
SD card slot
Indicator 2
Mounting Hook
Mounting Hook
LCD screen Display the visitors' image
Indicator1 Show the working status of monitor
Indicator2 Light on when the recorded pictures have not been viewed
Unlock button Press to release the door
Talk/Mon button
Press to communicate hands free with visitor
Press to view the outdoor condition in standby mode
Press to turn off staircase light,refer to part 3
Menu button Press twice to open the menu shortcuts.
Microphone Receive voice from the user
Mounting hook Use to hang up the monitor
Connection port Bus terminal
Speaker Send out vioce from the visitor
Key functions
-1-

2. Monitor Mounting
3. About Main Menu
145~160 cm
Accessory ttings:
1) Mounting Bracket and special 4 core wire
2) Two screws of 4X25 are used to fasten the Mounting Bracket on the wall.
Installation steps:
■ Installation Height for indoor monitor usually is 145- 160CM (refer to sketch map)
■ Attach the screws to the wall to x the mounting bracket.
■ Refer to the system connection section of this manual, connect wires correctly.
■ Hang the monitor rmly on the bracket.
The Main Menu is your starting point for using all the applications on your monitor.
To open the Main Menu page, tap either " Menu" key twice on the monitor or press
the screen anywhere twice.
-2-
Current time 04:29PM
:This icon will be displayed when the staircase light item is light on if the system connect VT-RLC module which control light.
otherwise,it won't be displayed.Touching this icon or pressing TALK/MON button can turn off the light.
:This icon will be displayed when the recorded pictures have not been viewed,touching this icon can see the recorded pictures.
Current date
Manual
Memory Album User Setup Close
Monitor
Playback
Monitor Intercom Inner Call

4. System Wiring
Terminal Discription
Basic Connection
JS-OS1
Input 1 Input 2 Output
JS-AP
Handset 75 Ohm Power
JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
1) DC-IN:Power supply connection port
2) JP/VD:JP/VD is used for setting the video impedance.
3) JS-AP:Audio phone or VT-RLC connection port
4) JS-OS1:The rst door station connection port
5) JS-OS2:The second door station connection port
6) JS/VD:Extended slave monitor connection port
AC ~
1R 2W 3Y 4B
1R 2W 3Y 4B
1
2
3
4
Door station
Black
Yellow
Red
White
Black
Yellow
Red
White
Reserve
JS-OS1
Input 1 Input 2 Output
JS-AP
Handset 75 Ohm Power
JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V
2W
4B
2W
3Y
4B
1R
2W
3Y
4B
1R
2W
3Y
4B
-3-

Extending Monitors
White
Red
Yellow
Black
Door station
Camera Note:To the first & last monitor,JP/VD jumper should reserve! others should remove.
1#
Monitor
2#
Monitor
N#
Monitor
JP/VD Removed!
JP/VD Reserved
JP/VD Reserved
PS PS PS
44 4
Extending Audio Phone:
AC ~ AC ~ AC ~
Red
White
Black
Black
White
Red
+12
2W 4B
GX-3P
JS-AP
JS-LK
INSIDE
(90 Degree ROTATE)
Back View
Back View
User code=1
User code=1 User code=2
User code=2 User code=N(N<5)
Reserve
Remove
Reserve
1 2 3 4
Back View
1 2 3 4
Back View
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
User code=N(N<5)
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
-4-

Extending 2 Outdoor Stations
JP/VD Reserve!
Black
Yellow
Red
White White
Red
Yellow
Black
2#
Camera
1#
Camera
1#
Camera
2#
Camera
1#
Monitor
NOTE: 1.
To the first & last monitor,JP/VD jumper should reserve! others should remove
.
2.When connect two Outdoor Stations, 2 Way Input item should be set to 1 on the 1# Monitor. (Main Menu-User Setup-Installer Setup-2 Way Input)
2#
Monitor
N#
Monitor
JP/VD Removed!
JP/VD Reserved
PS PS PS
4 4
4 4
User code=1 User code=2 User code=N(N<5)
User code=1 User code=2 User code=N(N<5)
Back View AC ~
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
AC ~ AC ~
Remove
Reserve
Reserve
Back View
1 2 3 4
Back View
1 2 3 4
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
-5-

1R
2W
3Y
4B
1R
2W
3Y
4B
VT-MDS
CCTV or Door station
door station
door station
door station
door station
Black
Yellow
Red
White
Black
Yellow
Red
White
SET
DS4
DS3
DS2
DS1
1#
2#
3#
4#
JW_VP
JW_VP
User code=1 User code=2 User code=N(N<5)
1 2 3 4
1 2 3 4
1 2 3 4
Reserve ReserveRemove
Note:To the first & last monitor,JP/VD jumper should reserve! others should remove.
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V
2W
4B
2W
3Y
4B
1R
2W
3Y
4B
1R
2W
3Y
4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V
2W
4B
2W
3Y
4B
1R
2W
3Y
4B
1R
2W
3Y
4B
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V
2W
4B
2W
3Y
4B
1R
2W
3Y
4B
1R
2W
3Y
4B
Extending Multi Door Stations with MDS
About the MDS instructions ,please refer to MDS user manual for more detail informations.
-6-

5. Basic Door Release Operation
1. Press the CALL button on door station.
2. The monitor rings,and the visitor's image will be seen on screen.
Note:the screen turns off after 30 seconds(default) if nobody answers.
3. Press either TALK/MON Button on monitor or touch Talk icon on screen, you
can communicate hands free with the visitor for 90 seconds(default).After nishing
communication,press TALK/MON button or touch Talk icon again to end the
communication. If the system connects two or more Monitors, pick up any Monitor,
the others will be automatically shut off.
Answering a Door Call
Status bar
► 1.show the current door station for monitoring.
► 2.show the waiting time for calling.
► 3.if the monitor is set to silence mode,this icon
will be shown.
► 4.if the system connect VT-RLC module which
control light,and the Staircase Light item is set
to 1or 2 (refer to part 9->Staircase Light),this
icon will be shown when receive calling.
1 2 34
Door Release
Entrance Monitoring
During talking state, Press UNLOCK Button or touch Unlock1 icon to release
the door for the visitor.(
Note:if the system is connected
VT-RLC
module which control
lock, touch
Unlock2
icon to release the second lock connected to RLC,for more
information,please refer to VT-RLC user manual.
)
When the monitor is in standby mode, press TALK/MON Button(or touch Monitor
... item on main menu page), The screen can display the view of outside. If multi door
stations are installed, touch Select icon to get into the camera switch mode(or
directly touch Manual Monitor item on main menu page). Select door 1/2/3/4 to
monitor the door station or CCTV camera you want.See the following diagrams.
-7-
DS1 00:30

► “ ” means the current operating monitor.
► “ ” means the selected calling monitor.
► Each monitor is conged one unique user
code
！
6. Intercom Function
Intercom can be initiated by any Monitor.
Touch Intercom or Inner Call item on main
menu page. Intercom function is activated
when multi monitors are installed.
Intercom: press Intercom icon on any
monitor to enter selective intercom page, see
the diagram on right.select one of user,then
press Dial Number icon to call.If the
selected monitor answers the call,intercom
talking is strating.
Inner Call: press Inner Call icon on any
monitor to enter selective intercom page, see
the diagram on right.All monitors will ring
at the same time,whichever monitor answers
the call, conversation is starting.and the
other monitors will stop ringing .
DS-1 00:23
Note:
If the system install VT-QSW module,video
quad split monitor is available,see the
diagram on right(please note that the quad
interface just display when install QSW
unit).for more detail information,please
refer to VT-QSW user manual.
-8-
1 2
User 1
Dail Number Return
User 2
User 3
User 4
User 5
Redial
Dail Number Return
User 1
User 2
User 3
User 4
User 5
Door 1 Door 2 Door 3 Door 4
Door 1
Camera 1 Camera 2 Camera 3 Quad
Door 2 Door 3 Door 4
Selective Intercom
Selective Intercom
！

7. Memory Sharing
Wiring Diagram for Memory Sharing
VT-BDU
4B3Y
2W
1R
4B3Y
2W
1R
4B3Y
2W
1R
4B3Y
2W
1R
VT-BDU
JW/VP1
JW/VP2 JW/VP3
JW/OS
HI
75R
150R
SET-3Y
SET-3Y
AC ~
1 2 3 4
1 2 3 4
AC ~
1 2 3 4
AC ~
1 2 3 4
White
Red
Yellow
Black
Door station
AC ~
Back View
User code=1 VT27SD/TD7 VT27/TD7
VT27/TD7
VT27/TD7
User code=2
User code=3
Reserve
JP/VD Reserved
JP/VD Reserved
JP/VD Reserved
User code=N(N<5)
JS-OS1
JS-AP JP/VD DC-IN
DC- DC+
JS-OS2 JS-VD
1R
12V 2W 4B
2W
3Y 4B
1R
2W
3Y 4B
1R
2W
3Y 4B
About the BDU instructions ,please refer to BDU user manual for more detail informations.
-9-