V-tech GearZooz Gear Up & Go Activity Table Assembly Instructions

Parent’s Guide
Gear Up & Go Activity Table
91-003537-001 UK

2
2
2
INTRODUCTION
Thank you for purchasing the VTech®GearZooz®Gear Up & Go
Activity Table.
This interactive activity table features activities that introduce
animals, numbers, colours, instruments and songs!
Off/Low/High
Volume Switch Activity Switch
Standard
Pole
Light Up
Dancing
Stage
Purple
Smart Pole
Trigger
Gears
5 Instrument Keys
3 Smart Gear™ Animals
12 Standard Gears Handle Gear

3
3
3
• ThreeSmartGear™animals
• 12standardgears
• Onehandlegear
• Onemonkey
• Onelabelsheet
• Oneparent’sguide
INCLUDED IN THIS PACKAGE
A: One table top
C: Two joints
B: Two screw bolts
D: Four table legs

4
4
4
WARNING:
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties and packaging screws are not
part of this toy, and should be discarded for your child’s safety.
NOTE:
Please keep this parent’s guide as it contains important
information.
Unlock the packaging locks
Rotate the packaging locks 90 degrees
anticlockwise.
Pull out the packaging locks.
Remove the Cable Ties:
Cut the ties with a pair of scissors.
Remove the ties.
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover at the bottom
of the unit. Use a screwdriver to
loosen the screw.
3. Install 2 new AA size (AM-3/LR6) batteries following the diagram
inside the battery box. (The use of new alkaline batteries is
recommended for maximum performance).
4. Replace the battery cover and tighten the screw to secure.

5
5
5
BATTERY NOTICE
• UsenewalkalinebatteriesorfullychargedNI-MH(NickelMetal-
hydride) rechargeable batteries for best performance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard
(carbon-zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinre.
• Donotchargenon-rechargeablebatteries.
• Removerechargeablebatteriesfromthetoybeforecharging(if
removable).
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates
they must not be disposed of in domestic waste as
they contain substances that can be damaging to the
environment and human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on
the market after 13th August, 2005.
Help protect the environment by disposing of your
product or batteries responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com

6
6
6
table topjoints
screw
bolts table legs
ASSEMBLY INSTRUCTIONS
With the VTech®GearZooz®Gear Up & Go Activity Table, safety
comesrst.Toensureyourchild’ssafety,adultassemblyisrequired.
1. Insert 2 table legs into one of the joints as shown in the picture.
Firmly push the legs into the joint until they click into place.
Repeat the above step for the other joint and 2 legs.
1

7
7
7
2. Insert the screw bolt into the hole on top of the assembled legs,
then insert the end of the screw bolt into one side of the table as
shown in the picture. Firmly push the screw bolt into the table
until it clicks into place. Then, turn the screw clockwise until you
hear a click sound to secure the leg to the table.
Repeat these steps with the other assembled leg.
3. Align and insert the monkey into
the round hole as shown in the
picture. You will hear a click when it
is secure.
3
2

8
8
8
4 Toplaywiththegearboardside,turnthetableoverandlayitat
ontheoor.Then,pressandholdthepurplebuttonandturnthe
screw anticlockwise once. You can then release the purple button
and continue to turn the screw anticlockwise to loosen it. Repeat
thisstepfortheotherassembledleg.Next,Flipthetablebackover.
Thegearboardcanberotatedsoitisat,oratanangle.Position
the table to the angle you would like, then reconnect and secure the
assembled legs to the table (refer to step 2 for instructions).
Repeat these steps to return to the activity centre side.
4

9
9
9
5. Todetachthetablelegs,turnthetableoverandlayitatonthe
oor.Then,pressandholdthepurplebuttonandturnthescrew
anticlockwise once. You can then release the purple button and
continuetoturnthescrewanticlockwisetoloosenit.Next,press
and hold the purple button and pull the assembled leg out of the
table.
Repeat the above step for the other leg.
5