V-tech Go Go Smart Wheels Car Assembly Instructions

Parent’s Guide
Save the Day Fire Station™
91-003367-001

2
PB
PB
2
4 SmartPoint
®
Locations
SmartPoint
®
Fire Truck
Fire Pole
Elevator
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®Save
the Day Fire Station™! Place Francis the SmartPoint®Fire Truck on top
of the fire station and watch him slide down, raise him up in the elevator
or spin him down the fire pole to promote motor skill development.
The four SmartPoint® locations trigger songs, melodies, sounds and
phrases that will engage your little one on their playtime mission.

3
PB
PB
3
One SmartPoint®
Fire Truck
One SmartPoint®
fire station
One pole
One parking
bracket
One SmartPoint®
base, blue
One house wall
One spinning
platform
One SmartPoint®
elevator platform
One base, gray
One sign
One SmartPoint®
parking platform
One top ramp
track support
INCLUDED IN THIS PACKAGE

4
PB
PB
4
One top ramp
track
One bottom ramp
track support
One 90-degree
track, male
One parent’s guide
One bottom ramp
track
One cross track
Two end tracks,
male
One fire piece
One label sheet
Two fire plates
Two 1/4 straight
tracks
User’s Manual
UK
Fire Station
TM © 2017 VTech
Printed in China
91-003367-000

5
PB
PB
5
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous les
produits d’emballage tels que rubans adhésifs, feuilles de plastique,
attaches, étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE : Il est conseillé de conserver ce guide des parents car il
comporte des informations importantes.
Unlock the packaging locks:
GETTING STARTED
BATTERY INSTALLATION
Fire Truck
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom of
the Fire Truck. Use a coin or a screwdriver
to loosen the screw.
3. Install 2 new AAA (AM-4/LR03) batteries
following the diagram inside the battery
box. (The use of new alkaline batteries is
recommended for maximum performance.)
4. Replace the battery cover and tighten the
screw to secure the battery cover.
Turn the packaging locks counterclockwise
several times.
Pull out and discard the packaging lock.

6
PB
PB
6
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

7
PB
PB
7
LABEL APPLICATION
Please stick the labels to the playset securely as indicated on
the following pages:

8
PB
PB
8
6 5 9
2
4
3
10
7
1
17
14
13
20
18
16
23
8
19
21
22
25 24 11
12 12
15
12 12
12 12
12 12 12
12

9
PB
PB
9
ASSEMBLY INSTRUCTIONS
Save the Day Fire Station
™
1. 1. Connect the Blue Base and Gray Base together. Then, attach
the Fire Station to the bases, as shown below.You will hear a “click”
sound when the Fire Station is secure. Once the Fire Station is
attached, it cannot be removed.
2. Insert the Sign into the top of the Fire Station. You will hear a
“click” sound to indicate it is secure.
With the VTech®Go! Go! Smart Wheels®Save the Day Fire
StationTM, safety comes first. To ensure your child’s safety, adult
assembly is required.

10
PB
PB
10
3. Attach the House Wall to the Gray Base and Fire Station, as
shown below. You will hear a “click” sound to indicate it is secure.
Once the House Wall is attached, it cannot be removed.
4. Attach the Elevator Platform to the Fire Station, as shown below.
Lift it up and down smoothly to make sure it is secure.
5. Insert the Top Ramp Track Support into the Gray Base.You will
hear a “click” sound to indicate it is secure. Once the Top Ramp
Track Support is attached, it cannot be removed.