V-tech Go! Go! Smart Wheels Mickey Magical... Assembly Instructions

Mickey Magical Wonderland
91-003541-000
Parent’s Guide
© Disney
www.disney.com

2
Castle 5Smartpoint®Locations
Donald Boat
Roundabout Smartpoint®Mickey Car
Ferris Wheel
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels® Mickey
Magical Wonderland! Hop into the Car with Mickey and ride around
this magical town. Ride on the Ferris Wheel, slide down the ramp,
push the boat back and forth, spin the gears and open the peek-a-boo
windows to promote motor skills.

3
INCLUDED IN THIS PACKAGE
One SmartPoint®
Mickey Car
One castle top One castle wall
One elevator One elevator wall One elevator base
One castle support Ramp track A Ramp track B
One ramp track support One boat piece One boat base

4
Two cross tracks
One 60-degree
track, male
One 60-degree
track, female
One turnabout sign
One 1/4 straight track
One 3/4 straight trackOne gate 3/4
straight track
One gate
One 90-degree
track, male
One 1/2 straight
track
One Ferris wheel
straight track
One roundabout

5
- One parent’s guide
WARNING:
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties and packaging screws are not
part of this toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches, étiquettes et vis d’emballage. Ils ne font pas
partie du jouet.
NOTE: Il est conseillé de conserver ce guide des parents car il
comporte des informations importantes.
Adult assembly required.
Ce jouet doit être assemblé par un adulte.
92-010263-000-100
M/N:80-512400-000-001
P/N:92-0102603-000-100
Size:340mm x 220mm
Printing:4C+UV
One Ferris wheel One label sheet
Unlock the packaging locks:
Turn the packaging lock anticlockwise
several times.
Pull out and discard the packaging lock.

6
GETTING STARTED
BATTERY INSTALLATION
Car
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
bottom of the Car. Use a screwdriver
to loosen the screw.
3. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended for
maximum performance).
4. Replace the battery cover and tighten
the screw to secure the battery cover.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Removerechargeablebatteriesfromthetoybeforecharging(if
removable).
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.

7
92-010263-000-100
M/N:80-512400-000-001
P/N:92-0102603-000-100
Size: 340mm x 220mm
Printing:4C+UV
GETTING STARTED
Please stick the labels to the playset securely as
indicated on the following page:
12
34
5
67 8 9
10
11
12
13 14
15
16
18 19
20 21
17
1
6 7 2120 8 9
5
19
13 14
15
3
17 18 2 4
1011
16
12

8
ASSEMBLY INSTRUCTIONS
Mickey Magical Wonderland
With the VTech®Go! Go! Smart Wheels®Mickey Magical
Wonderland, safety comes first. To ensure your child’s safety,
adultassemblyisrequired.
1. Attach the Elevator Base to the Elevator Wall. Then, insert the
Elevator into the Elevator Wall, as shown below. You will hear a
“click” sound to indicate the pieces are secure.
2. Next,assemblethecastlefollowingthestepsbelow:
A. Attach the Castle Wall and Elevator Wall to the Castle Top,
as shown below. You will hear a “click” sound to indicate the
pieces are secure.

9
B. Insert the Castle Support into the Castle Top, as shown below.
You will hear a “click” sound to indicate the pieces are secure.
3. Connect Ramp Track A and B. Then, attach the Ramp Track
Support to the Ramp Tracks, as shown below. You will hear a
“click” sound to indicate both pieces are secure.
4. Connect the Boat Piece into Ramp Track B.Then, attach the Boat
Base to the Boat Piece, as shown below. You will hear a “click”
sound to indicate both pieces are secure.
5. Attach Ramp Track A to the Castle Top, as shown below.

10
6. Insert the Roundabout Sign into the Roundabout, as shown below.
7. Place the Gate in the Gate 3/4 Straight Track, as shown below.
8. Attach the Ferris Wheel to the Ferris Wheel Track, as shown
below.You will hear a “click” sound to indicate the pieces are secure.
After the above steps, connect these pieces to the included track pieces.
You can configure them into different arrangements.