V-tech Go!Go! Smart Wheels Park & Learn Deluxe... User manual

© 2015 VTech
Printed in China
91-003022-004
User’s Manual
Park & Learn Deluxe Garage™

2
SMARTPOINT®
TOW TRUCK
ELECTRONIC GATE
ON/OFF/VOLUME
CONTROL SWITCH 3 LIGHT-UP
BUTTONS
ELEVATOR/
LAUNCHER
HELICOPTER
PA D
VEHICLE LIFT
9 SMARTPOINT®
LOCATIONS
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®Park
& Learn Deluxe Garage™!
Park, play and learn with the Go! Go! Smart Wheels®Park & Learn
Deluxe Garage™.This interactive garage features three floors of pretend
play and learning fun.
INTRODUCTION

33
INCLUDED IN THIS PACKAGE
INCLUDED IN THIS PACKAGE
One elevator tower One vehicle lift
One welcome gate
One SmartPoint®
tow truck
One SmartPoint®
toll booth
One curved ramp track One straight ramp track
One first floor
SmartPoint
®
platform
One second floor
SmartPoint
®
platform
One third floor
SmartPoint
®
platform
One fuel accessory

4
INCLUDED IN THIS PACKAGE
Two male/female connector tracks
Two male connector tracks
One 90-degree female track
One 90-degree male track
One elevator support piece
One user’s manual
One label sheet
One snap-in large support
One medium support
One snap-in small support
One mini support
Two snap-in mini supports

5
GETTING STARTED
BATTERY INSTALLATION – TOW TRUCK
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the tow truck. Use a coin or a
screwdriver to loosen the screw.
GETTING STARTED
CAUTION:
Adult assembly required. For your child’s safety, do
not let your child play with the toy until it is fully
assembled.
WARNING:
All packing materials, such as tape, plastic sheets, packaging
locks and tags are not part of this toy, and should be discarded
for your child’s safety.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches et étiquettes. Ils ne font pas partie du jouet.
NOTE:
Please keep this user’s manual as it contains important
information.
Unlock the packaging locks:
Turn the packaging lock counter-clockwise
several times.
Pull out and discard the packaging lock.

6
3. Install 2 new “AAA” (AM-4/LR03) batteries following the diagram
inside the battery box. (The use of new alkaline batteries is
recommended for maximum performance.)
4. Replace the battery cover and tighten the screw to secure the
battery cover.
BATTERY INSTALLATION - GARAGE
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the top
platform of the Park & Learn Deluxe
Garage™. Use a screwdriver to loosen
the screw.
3. Install 2 new ‘AA’ (AM-3/LR6) batteries
following the diagram inside the
battery box. (The use of new alkaline
batteries is recommended for maximum
performance.)
4. Replace the battery cover and tighten the
screw to secure the battery cover.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
BATTERY NOTICE

7
LABEL INSTRUCTIONS
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Please adhere the labels to the playset
securely as indicated on the following
page:
1
4
56
8
8
910
7
11
12
217 18
13 14 15 16

8
9
2
18
17
510
13
14
16
11
15
12 6
1
4
7
LABEL INSTRUCTIONS
8

9
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
With the VTech® Go! Go! Smart Wheels®Park & Learn Deluxe
Garage™ safety comes first. To ensure your child’s safety, adult
assemblyisrequired.
1. With the first floor platform right-side up, insert the two snap-in
mini supports into the slots on the first floor platform as shown.The
snap-in mini supports will fit in the slots snuggly. The teeth on the
snap-in mini supports will grip to the first floor platform.
2. With the second oor platform upside-down, insert the snap-in
small support into the slot on the second oor platform as shown.
The snap-in small support will t in the slot snuggly. The tooth on
the small support will grip to the second oor platform.