V-tech Glitter Me Kitty Assembly Instructions

Parent’s Guide
91-004021-001-006 UK
Glitter Me Kitty

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01

2
2
2
INTRODUCTION
Add some sparkle to your day with your new bestfriend Glitter Me
Kitty by VTech®! When this super cute, super cuddly meow-gical
kitty is happy or when you stroke her head, she will move her paw
and place a glitter stamp on your hand to show you she loves you.
Is she hungry, sleepy or itchy? Colour-changing stripes on her head
will show you how she’s feeling. Discover what she’s saying by
pressing her tummy to translate her meows into words! Respond to
her needs by scratching her head or stroking her on the back until
she falls asleep. You can even feed her with her very own bottle.
Off/Low/High
Volume Switch
Light Up Head Button
Mouth Button
Back Button
Tummy Button

3
3
3
INCLUDED IN THE PACKAGE
• Glitter Me Kitty
• 1 Bottle
• 1 Ink pad
• 1 Parent’s Guide
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy, and should be discarded for your child’s safety.
NOTE
Please save this Parent’s Guide as it contains important information.
GETTING STARTED
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the battery cover located on the
bottom of the kitten, use a screwdriver to
loosen the screw and open the battery
cover.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 3 new AA batteries following the
diagram inside the battery box.
5. Replace the battery cover and tighten the
screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.

4
4
4
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as recommended
are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES
• Remove rechargeable batteries from the toy before charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
Removing the Packaging Locks:
Rotate the packaging locks anticlockwise 90
degrees.
Pull out the packaging locks and discard.
To Begin Playing With Glitter Me Kitty
When you play with Glitter Me Kitty for the first time, slide the
switch from the High Volume position to the Low Volume position
and wait for a few seconds to exit Try-Me mode. You will hear three
beeping sounds when you have exited Try-Me mode. You can then
press any button to activate the unit and start playing.

5
5
5
WARNING:
1. NOT for children under 4 years old. KEEP OUT OF REACH of
very young children.
2. Follow all instructions and use under adult supervision.
3. Not to be eaten. Use only as directed.FOR EXTERNAL USE
ONLY. DO NOT USE on face. KEEP AWAY from eyes or lips.
Rinse eyes with water immediately if product comes into contact
with them.
4. DISCONTINUE USE if rash develops.
5. DO NOT USE if the packaging is already opened or tampered
with.
Glitter ink is NON-TOXIC. Conforms to ASTM D4236 and all FDA
cosmetic safety regulations. It is laboratory tested and safe for use
as recommended. As with all cosmetics, some individual skin types
may experience minor skin irritation. If this occurs, discontinue use,
and consult a doctor if necessary.
IMPORTANT: The glitter ink is ONLY for printing on hands. DO NOT
USE on clothing and other articles of daily use. AVOID contact with
fabrics, carpets, and upholstery. In case of contact with clothing,
rinse with soap and water immediately.

6
6
6
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
VTech®cares for the planet.
Care for the environment and give your toy a second life by
disposing of it at a small electricals collection point so all its
materials can be recycled.
In the UK:
Visit www.recyclenow.com to see a list of collection points near you.
In Australia & New Zealand:
Check with your local council for kerbside collections.

7
7
7
How to Install the Ink Pad
With the Glitter Me Kitty, adult assembly is required.
Please note that Glitter Me Kitty comes with a pink decorative cover
on her paw. This cover will need to be removed and the ink pad
installed so that the Glitter Me Kitty can stamp hands.
1. Pull the decorative cover off the kitten’s paw.
2. Remove the ink pad from the aluminum
packaging and remove the plastic ink cover
from the ink pad.
3. Put the ink pad on the kitten’s paw, with the
tip of the heart pointed toward the paw.
4. Press down firmly on both sides of the ink
pad. You will hear it click into place when
inserted properly. The ink pad is now ready
to use.
5. Put the decorative cover and plastic ink
cover together by aligning their latches,
and store them on the bottom of the kitten,
with the cover’s latch facing the Off/Low/
High Volume Switch and decorative cover
facing in.
6. When not using the ink pad for an extended
period, we suggest taking it out, putting the
ink cover back on and storing it in a cool,
dry location.
7. Clean the stamp and the inside of the
kitten’s paw with a damp cloth, then place
the decorative cover back on the top of the
kitten’s paw for protection.
8. The ink washes off with soap and water.

8
8
8
WARNING
The ink pad is ONLY for stamping paw prints onto your hand. It is not
intended for any other use.
Please read all of the safety warnings in this Parent’s Guide before
use.
NOTE: Before using the ink pad, please test a small amount of ink
on the inside of your wrist to ensure there is no reaction or skin
sensitivity.
PRODUCT FEATURES
1. Off/Low/High Volume Switch
This switch is located on the bottom of
the unit.
To turn the unit On, slide the switch
from Off to the Low Volume or High
Volume position. To turn the unit Off,
slide the switch to Off position.
2. Light Up Head Button
Press the Head Button for three
responses:
1) Press and hold for 2 seconds and the
kitten will move her paw to give you a
stamp.
2) Press once to hear cute kitten sounds
or listen for hints on how to respond to
what the kitten needs.
3) Press twice to hear the kitten sing
songs. Also, keep an eye on the colours
of the lights on the kitten’s head, as they
indicate the kitten’s mood.

9
9
9
3. Tummy Button
1) After pressing the Back Button, Head
Button or Mouth Button, press the
Tummy Button to hear what the kitten
said.
2) When the kitten meows, press the
Tummy Button to translate current purrs
or meows into human voice.
3) If you want to hear different voice lines,
you can press the Back Button, Head
Button or Mouth Button again and then
press the Tummy Button.
4. Back Button
1) Press to hear different kitten sounds.
2) Quickly press two times to hear the
kitten sing playful songs.
3) When the kitten is itchy, this and the
Head Button are great spots to scratch!
5. Mouth Button and Bottle
1) Press to hear different kitten sounds.
2) Press three times or long press for
several seconds to feed your kitten
when she feels hungry.
3) Use the Bottle to feed your kitten
anytime or when your kitten feels
hungry. Be careful not to feed her too
much, or she will get the hiccups or
need to burp.