V-tech Lullaby Bear Crib Projector User manual

Lullaby Bear Crib Projector
User’s Manual
© 2011 VTech
Printed in China
US
91-002346-014
new im Cover(101x127).indd 1
11/17/11 7:40:50 PM

User’s Manual
new im Cover(101x127).indd 1 11/17/11 2:20:46 PM

2
INTRODUCTION
Thank you for purchasing the VTech®Lullaby Bear Crib ProjectorTM
crib toy!
The Lullaby Bear Crib ProjectorTM will soothe baby into a peaceful
sleep. Baby will relax as soothing images project onto the ceiling, while
soft melodies, nature sounds and soothing phrases lull baby to sleep.
The nursery mode creates a peaceful environment with gentle sing
along songs, phrases and melodies. The nature mode will have a softer
effect with subtle nature sounds. Press the cute teddy bear button to
rotate the melodies, sing along songs or nature sounds.
Introduction
timer
switch
light projector
selector
bear button
crib attachment
strap
Volume control
on/oFF/moDe
selector
switch
100000IM.indd 2 12/24/08 12:04:53 PM

3
INCLUDED IN THIS PACKAGE
- One VTech®Lullaby Bear Crib ProjectorTM
- One crib attachment strap
- One instruction manual
WARNING: All packing materials, such as tape, plastic sheets,
wire ties and tags are not part of this toy, and should
be discarded for your child’s safety.
Please loosen the battery cover screws slightly and
remove the wire packaging ties.
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the back of
the unit. Use a coin or a screwdriver to
loosen the screw.
3. Install 3 new ‘AA’ (AM-3/LR6) batteries
following the diagram inside the
battery box. (The use of new alkaline
batteries is recommended for maximum
performance.)
4. Replace the battery cover and tighten the
screw to secure the battery cover.
BATTERY NOTICE
•Install batteries correctly observing the polarity (+, -) signs to avoid
leakage.
•Do not mix old and new batteries.
Instructions & Activities
100000IM.indd 3 12/24/08 12:04:54 PM

4
• Do not mix batteries of different types: alkaline, standard (carbon-
zinc) or rechargeable (nickel-cadmium).
• Remove the batteries from the equipment when the unit will not be
used for an extended period of time.
• Always remove exhausted batteries from the equipment.
• Donotdisposeofbatteriesinre.
• Do not attempt to recharge ordinary batteries.
• The supply terminals are not to be short-circuited.
• Only batteries of the same and equivalent type as recommended
are to be used.
WE DO NOT RECOMMEND THE USE OF RECHARGEABLE
BATTERIES.
With the VTech®Lullaby Bear Crib ProjectorTM,safetycomesrst.
To ensure your child’s safety, the assembly of this product is an adult
activity, not a child’s activity. Please ensure that the crib attachment
strap is securely locked into position to avoid injury. Follow the
instructionsbelowcarefullyandmakesurethenalassemblyiscorrect.
Attach only to cribs with sturdy rails and spindles. Do not attach to
playpens with mesh walls.
Please make sure the crib attachment strap is out of reach from children
when placed in the crib. Please ensure the crib light is positioned in the
upright position with the projection light facing directly upwards.
Please remove the crib attachment strap from the unit if it is going to
be used outside the crib.
Instructions & Activities
100000IM.indd 4 12/24/08 12:04:54 PM

5
Instructions & Activities
ASSEMBLY INSTRUCTIONS
1. Place the unit in the crib bringing the
strap over the top rail. Slip the top of
the strap under the slot on the back
of the unit and secure. You can adjust
the hanging height by choosing the
appropriate hole on the top of the
strap.
2. Pull slightly on the unit to make sure the
strap has been securely fastened. The
unit should be snug against the crib
rail. Please check the unit frequently
to ensure it is still secure.
PRODUCT FEATURES
1. ON/OFF SWITCH
To turn the unit ON, slide the ON/
OFF/MODE SELECTOR SWITCH
to the NURSERY MODE ( ) or
NATURE MODE ( ) position.To turn
the unit OFF, slide the ON/OFF/MODE
SELECTOR SWITCH to the OFF ( )
position.
2. TIMER SWITCH
Slide the timer switch to the demo, 5
or 10 minute setting. In the demo mode
you will hear a short demonstration
of the phrases, sounds, songs and
melodies. A soothing image will be
projected onto the ceiling for a short
time.
100000IM.indd 5 12/24/08 12:04:56 PM

6
3. VOLUME CONTROL
To adjust the volume, press the LOW
VOLUME BUTTON ( ) or the HIGH
VOLUME BUTTON ( ).
4. LIGHT PROJECTOR SELECTOR
Press the light projector button to
switch the light projector off and on.
5. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech® Lullaby Bear Crib ProjectorTM
will automatically power-down without any input after the selected
time setting has finished playing. The unit can be turned on again
by sliding the timer or mode selector switch.
ACTIVITIES
1. Slide the on/off/mode selector
switchto turn the unit on. You will hear
soothing phrases, sing along songs
and soft sounds. A peaceful image will
be projected onto the ceiling.
Instructions & Activites
100000IM.indd 6 12/24/08 12:04:57 PM

7
2. Press the bear button to hear a
soft sing along song and a variety
of melodies in the nursery mode. In
the nature mode you will hear one of
two phrases followed by a variety of
melodies. A soothing image will be
projected onto the ceiling.
MELODY LIST
1. Brahms’ Lullaby
2. Are You Sleeping?
3. My Bonnie Lies Over the Ocean
4. Hush Little Baby
5. Beautiful Dreamer
6. Fur Elise
7. Greensleeves
8. Moonlight Sonata
9. Oh Where Has My Little Dog Gone?
10. Clair de Lune
11. Rock-a-Bye Baby
12. All Through the Night
13. Au Clair de la Lune
14. Shenandoah
15. Twinkle, Twinkle, Little Star
16. Sailing, Sailing
Instructions & Activities
100000IM.indd 7 12/24/08 12:04:58 PM

8
SONG LYRICS
SONG 1
Rock-a-bye baby, on the tree top,
When the wind blows, the cradle will rock.
SONG 2
Twinkle, twinkle, little star,
How I wonder what you are.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat
source.
3. Remove the batteries when the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
TROUBLESHOOTING
If for some reason the program/activity stops working or
malfunctions,please follow these steps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with an entire set of new
batteries.
Care & Maintenance/Troubleshooting
100000IM.indd 8 12/24/08 12:04:58 PM

9
If the problem persists, please call our Consumer Services Department
at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, and a
service representative will be happy to help you.
For information on this product’s warranty, please call VTech®1-800-
521-2010 in the U.S., or 1-877-352-8697 in Canada.
IMPORTANT NOTE:
Creating and developing Infant Learning products is
accompanied by a responsibility that we at VTech®take very
seriously. We make every effort to ensure the accuracy of the
information, which forms the value of our products. However,
errors sometimes can occur. It is important for you to know
that we stand behind our products and encourage you to call
our Consumer Services Department at 1-800-521-2010 in the
U.S., or 1-877-352-8697 in Canada, with any problems and/or
suggestions that you might have. A service representative will
be happy to help you.
FCC Notice:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Other Info
100000IM.indd 9 12/24/08 12:04:58 PM