V-tech Toot-Toot Drivers Monster Truck Rally Assembly Instructions

Monster Truck Rally
Parent’s Guide
91-003998-001 UK

2
Platform
Launcher
Jump
Launcher
Landing Ramp
Bridge
INTRODUCTION
Thank you for purchasing the Toot-Toot Drivers®Monster Truck
Rally.
Little racers will love performing all the stunts on this wild ride!
Launch the Monster Truck off one of two launchers and create
multiple configurations for even more fun. Plus, hear fun music and
sound effects when the vehicle responds to the four SmartPointTM
locations. It’s a great day to race!
4SmartPointTM
Locations
SmartPointTM
Monster Truck

3
INCLUDED IN THE PACKAGE
One SmartPointTM
Monster Truck
One jump launcher
base
One platform
launcher
Two 1/3 length
male track pieces
One stadium base
One fire arch
One slope track C
One stadium wall
One jump launcher
One landing ramp One slope track A One slope track B

4
Two cross tracks
Two platform
launcher supports
One switch track
One sign One sign base
One bridge
One end track
One S-track exit Two S-track supports
Three S-tracks One S-track platform
· Label sheet
· Parent’s Guide
A
A
A
B
B
B
C

5
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not
part of this toy, and should be discarded for your child’s safety.
NOTE
Please save this Parent’s Guide as it contains important information.
GETTING STARTED
Battery Removal and Installation
Monster Truck
1. Make sure the unit is turned Off.
2. Locate the battery cover on the
bottom of the Monster Truck. Use a
screwdriver to loosen the screw, then
open the battery cover.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box.
5. Replace the battery cover and tighten the screw to secure.
Unlock the Packaging Locks
Turn the packaging lock anticlockwise
several times.
Pull out the packaging lock and discard.

6
IMPORTANT: BATTERY INFORMATION
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotmixoldandnewbatteries.
• Donotmixalkaline,standard(carbon-zinc)orrechargeable
batteries.
• Onlybatteriesofthesameorequivalenttypeasrecommended
aretobeused.
• Donotshort-circuitthesupplyterminals.
• Removebatteriesduringlongperiodsofnon-use.
• Removeexhaustedbatteriesfromthetoy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinre.
RECHARGEABLE BATTERIES:
• Removerechargeablebatteriesfromthetoybeforecharging.
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.
• Donotchargenon-rechargeablebatteries.

7
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates
they must not be disposed of in domestic waste as
they contain substances that can be damaging to the
environment and human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on
the market after 13th August, 2005.
Help protect the environment by disposing of your
product or batteries responsibly.
VTech®cares for the planet.
Care for the environment and give your toy a second life by
disposing of it at a small electricals collection point so all its
materials can be recycled.
In the UK:
Visit www.recyclenow.com to see a list of collection points near
you.
In Australia & New Zealand:
Check with you local council for kerbside collections.

8
LABEL APPLICATION
Please stick the labels to the play set as shown below:
1
10
14
20
22
21
16
17
18
15
19
11
12
13
23
5
4
89

9
18
14
8
6
9
4
5
24
17
27
11
10
23
6
13
26
12
25
16
21
22
73
15 19
2
20

10
ASSEMBLY INSTRUCTIONS
With the Toot-Toot Drivers®Monster Truck Rally, safety comes
first. To ensure your child’s safety, adult assembly is required.
1. Connect the Platform Launcher and S-Track B with the
Stadium Wall.
2. Connect the Platform Launcher with S-Track A, and connect
S-Track A, S-Track C and Slope Track C with S-Track B.
3. Insert the Jump Launcher into the Jump Launcher Base, then
connect with Slope Track B and Cross Track B. Make sure you
hear a click to confirm the pieces are firmly connected.