V-tech Toot-Toot Friends User manual

User’s Manual
Enchanted Princess Palace
UK
91-003236-015

2
2
2
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot FriendsTM Enchanted
Princess Palace.
This amazing palace expands to more than 1.2m/4ft wide and has a
variety of luxurious rooms, including a ballroom, music room, kitchen,
parlour and observation tower. While exploring the palace with Princess
Darla, place her on the ve MagicPoint locations to experience her
bright and friendly personality! When Princess Darla sits at her
MagicPoint Tea Set table with a friend (additional characters sold
separately), they will chat and sing with each other.
THREE ACCESSORIES
CLOCK
TOWER
OBSERVATION
TOWER
LIFT
BALLROOM
SPINNING
WHEEL
MAGICCHAT
TEA SET
SWING
STAIRCASE
MAGICPOINT CHARACTER
PRINCESS DARLA

3
3
3
INCLUDED IN THIS PACKAGE
• One MagicPoint character - Princess Darla
• Two pillars
• One observation tower railing
• One ground oor main wall
• One 1st oor main wall
• One ground oor base and dance oor with one MagicPoint
location
• One 1st oor base with one MagicPoint location
• One bed
NOTE: This toy is not intended for teething.
• One harp • One mirror

4
4
4
• One clock tower
• Four ags
• One twin tower roof with toy engravings inside
• One twin tower roof with a smooth surface for label application
• One single tower roof
• Two piers
• One staircase
• One tower bridge
• One MagicPoint tea set
• One tea set base
• One tower base
• One lift platform
• One lift tower support cover
• One tower with lift support

5
5
5
• Two swing ropes
• Two doors
• One MagicPoint support cover
• One chandelier support cover
• Two label sheets
• One label instruction sheet
• User’s manual
• One small bridge
• One swing seat

6
6
6
Unlock the packaging lock:
There is one packaging lock located on the character.
Use a coin or screwdriver to loosen
the screw.
Pull out the screw with the packaging
lock and discard them.
1
2
WARNING:
All packing materials, such as tape, plastic sheets, screws,
packaging locks and tags are not part of this toy and should be
discarded for your child’s safety.
NOTE: Please keep this user’s manual as it contains important
information.
GETTING STARTED
BATTERY INSTALLATION -
CHARACTER
1. Make sure the unit is OFF.
2. Locate the battery cover on the bottom of the
unit. Use a screwdriver to loosen the screws.
3. Install 2 new “AAA” (LR03/AM-4) batteries
following the diagram inside the battery
box. (The use of new alkaline batteries is
recommended for maximum performance.)
4 Replace the battery cover and tighten the
screws to secure.

7
7
7
BATTERY NOTICE
• Alkaline Batteries are recommended. Rechargeable batteries are
not guaranteed to work with this product.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in re.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate
that the battery contains more than the specied value of
mercury (Hg), cadmium (Cd) or lead (Pb) set out in Battery
Directive (2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com

8
8
8
ASSEMBLY INSTRUCTIONS
With the VTech®Toot-Toot Friends™ Enchanted Princess Palace,
safety comes rst. To ensure your child’s safety, adult assembly is
required.
1 Insert the two PILLARS into the
GROUND FLOOR BASE as shown
in the picture. You will hear a “click”
sound when the pieces are secure.
2. Insert the GROUND FLOOR MAIN
WALL into the GROUND FLOOR
BASE as shown in the picture. You
will hear a “click” sound when the
pieces are secure.
3 Attach the two DOORS to the GROUND FLOOR MAIN WALL and
GROUND FLOOR BASE as shown in the picture.
Note: The door prongs are each a distinct shape. Carefully check
the shape of each door prong and ensure you are inserting it into
the correct hole.

9
9
9
4. Insert the OBSERVATION TOWER RAILING into the 1ST FLOOR
BASE. Then, insert the 1ST FLOOR BASE into the GROUND
FLOOR MAIN WALL as shown in the picture.
5. Insert the 1ST FLOOR MAIN
WALL into the 1ST FLOOR BASE
as shown in the picture.
6. Insert the CLOCK TOWER, a TWIN TOWER ROOF and the SINGLE
TOWER ROOF into the 1ST FLOOR MAIN WALL as shown in the
picture. You will hear a “click” sound when the pieces are secure.
Twin Tower with
Toy Engravings