V2 HURRICANE-RS User manual

V2 S.p.A.
Corso Principi di Piemonte, 65/67
12035 RACCONIGI (CN) ITALY
tel. [phone] - fax [phone]
[email protected] - www.v2home.com
HURRICANE-RS
IL n. 280
EDIZ. 13/07/2011
ANEMOMETRO CON SENSORE DI SOLE E
TEM ERATURA - SEGNALE VIA RADIO
ANEMOMETER WITH SUN AND
TEM ERATURE SENSOR - WIRELESS
ANÉMOMÈTRE AVEC CA TEUR DE SOLEIL
ET TEM ÉRATURE - AR RADIO
ANEMOMETER MIT SONNEN- UND
TEM ERATURSENSOR - U?BER FUNK
ANEMÓMETRO CON SENSOR DE SOL Y
TEM ERATURA - VIA RADIO
ANEMÓMETRO COM SENSOR DE SOL E
TEM ERATURA - COMANDO VIA RÁDIO
I
GB
F
D
E

Fig.1
2 x 1 mm2 (300/500V)

Fig.3
Fig.2
L (BROWN)
phase 230V
N (BLUE)
neutral 230V

ENGLISH
ANEMOMETER WITH SUN AND
TEM ERATURE SENSOR – REMOTE CONTROL
The HURRICANE-RS sensor detects the sun, wind, and
temperature parameters and transmits them by radio to the
remote controller.
If the SUN threshold is exceeded, an OPEN command is sent to
the sunshade, whereas if the WIND threshold is exceeded, a
CLOSE command is sent.
Using 2 buttons and 8 LEDs, the thresholds for the sensors can
be set and the device can be memorized on the controlled
remote controller.
To install HURRICANE-RS, carefully read these instructions.
CAUTION: If the system is left unattended for long periods,
we recommended that the sunshade be closed and that
the sun sensor's automatic function be deactivated.
TECHNICAL DATA
1. DEVICE MEMORIZATION ON REMOTE
CONTROLLERS
1. Move to a position close to the remote controller that will be
controlled
2. Power the device with a temporary cable
3. If the sunshade is controlled with transmitters in the DUO
series, use a remote control that is already memorized in the
controller and proceed as follows:
a. Press SELC on the transmitter a few times, until the LEDs
display the channel memorized (only DUO6 and DUO4)
b. Return the awning to its mid-height
c. Move Switch 1 on the transmitter to the ON position
d. Press and hold down PROG on the transmitter for about 5
seconds, until the motor starts to move
e. Release PROG and the motor will stop
f. Press 1 on HURRICANE-RS for at least 2 seconds (Fig.2)
g. To check that it has been memorized correctly, press 1:
the sunshade should CLOSE. If not, repeat the procedure
4. If the sunshade is controlled with transmitters in the ADLER
series, use a remote control that is already memorized in the
controller and proceed as follows:
CAUTION: If the remote control used has multiple channels,
first select the channel memorized in the controller using C.
a. Press and hold down the UP and DOWN buttons on the
remote control until the motor starts to move in one
direction.
b. Release the buttons and the motor will stop.
c. Within 8 seconds, press 1 on HURRICANE-RS for at least
2 seconds
d. To check that it has been memorized correctly, press 1:
the sunshade should CLOSE. If not, repeat the procedure.
2. INSTALLATION
CAUTION: For correct operation, please remember that the
sensor must be positioned near the sunshade it protects and in
an area exposed to sun and wind.
The articulated arm should be parallel to the ground and
the blades should be turned downwards (Fig. 3).
Before attaching the device, make sure the radio coverage is
sufficient: put HURRICANE-RS in the position for installation and
press 1. Check that the sunshade closes.
CAUTION: Check that there are no other devices operating on
the same frequency (434.15 MHz) and with continuous
transmission, such as alarms, radio headphones, etc., which may
interfere with the communication between the sensor and the
command controller. Installing more HURRICANE-RS sensors in
the same area could give rise to the same problem.
If the radio channel is not accessible for more than 15 minutes,
for safety reasons the controller closes the sunshade and blocks.
The system will return to normal operation once the controller
again receives the radio signal from the sensor.
To force exit from the BLOC state, power must be disconnected
from the command controller for a few seconds.
1. Remove the cover (Fig. 1)
2. Attach the device to the wall using the provided wall plugs
(Fig. 1)
3. Position the articulated arm horizontally with the blades
turned downwards (Fig. 3)
CAUTION: If the articulated arm is not perfectly horizontal there
may be problems detecting the wind speed.
4. Tighten the screw, V1 (Fig. 3), to lock the movement of the
arm
3. ELECTRICAL WIRING
1. Connect a power grid cable (2 x 1.5 sq. mm section) on the L
and Nterminals
2. Block the cable using the provided cable gland
3. Close the cover
Maximum applicable voltage 230 V ~ 50Hz
Absorbed power 3,5 W
Transmission frequency 434,15 MHz
Protection IP44
Temperature for use -20 ÷ +60 °C

ENGLISH
4. SENSOR THRESHOLD LEVELS
To display and modify the threshold levels of the various sensors,
follow this procedure:
a) WIND Sensor
mCAUTION: To cause the sunshade to close, the wind sensor
must detect a value greater than the set threshold for at least 5
seconds. Closure of the sunshade due to strong wind causes the
system to block for 8 minutes.
1. Press 2: the WIND LED will turn on, identifying the wind
sensor, and at the same time the LED that displays the sensor
threshold level turns on:
LED 1 = level 1 = 10 km/h (default value)
LED 2 = level 2 = 15 km/h
LED 3 = level 3 = 20 km/h
LED 4 = level 4 = 30 km/h
LED 5 = level 5 = 40 km/h
2. To change the set level, press 1 a number of times until the
level you want is displayed (once level 5 is reached, the next
time it is pressed it restarts from level 1).
b) SUN Sensor
mCAUTION: To cause the sunshade to open, the sun sensor
must detect a value greater than the set threshold for at least 8
minutes.
To cause the sunshade to close, the sun sensor must detect a
value less than the set threshold for at least 8 minutes.
1. Press 2 twice: the SUN LED will turn on, identifying the sun
sensor, and at the same time the LED that displays the sensor
threshold level turns on:
LEDs OFF = sensor disabled
LED 1 = level 1 = 2 klux
LED 2 = level 2 = 5 klux
LED 3 = level 3 = 10 klux (default value)
LED 4 = level 4 = 20 klux
LED 5 = level 5 = 40 klux
2. To change the set level, press 1 a number of times until the
level you want is displayed (once level 5 is reached, the next
time it is pressed it restarts from level 1).
c) TEM ERATURE Sensor
This function allows the temperature level below which the
device must not open the sunshade, even if the light intensity is
greater than the threshold level set.
This function is very useful in countries with cold climates, where
it is often sunny but very cold. Under these conditions it is not
necessary that the sunshade open, which would prohibit the
sun's rays from heating the inside space.
1. Press 2 three times: the TEM LED will turn on, identifying
the temperature sensor, and at the same time the LED that
displays the sensor threshold level turns on:
LEDs OFF = sensor disabled
LED 1=Level 1 = sensor disabled (default value)
LED 2 = Level 2 = 0 °C
LED 3 = Level 3 = 5 °C
LED 4 = Level 4 = 10 °C
LED 5 = Level 5 = 15 °C
2. To change the set level, press 1 a number of times until the
level you want is displayed (once level 5 is reached, the next time
it is pressed it restar
DECLARATION OF CONFORMITY
V2 SPA herewith states that the HURRICANE-RS models
are in accordance with the following EEC directive:
2004/108/CEE EMC directive
2006/95/CEE Electrical safety directive
99/05/CEE Radio directive
Racconigi, 02/02/2010
V2 SPA legal representative
Cosimo De Falco