Vacon 100 flow User manual

vacon 100 industrial
vacon 100 flow
ac drives
installation manual
ip00 drive modules
®
®

PREFACE
DOCUMENT DETAILS
Document ID: DPD01665D
Date: 6.11.2017
ABOUT THIS MANUAL
This manual is copyright of VACON Ltd. All Rights Reserved. The manual is subject to change
without prior notice. The language of the original instructions is English.
ABOUT THE PRODUCT
This manual describes the VACON®100 IP00 Drive Module. The drive has a power range of
75-800 kW, and a voltage range of 208-240 V, 380-500 V, or 525-690 V. The drive is available in
4 different enclosure sizes: MR8, MR9, MR10 and MR12. The enclosure class of the drive is
IP00, and that is why the drive must be installed in a cabinet or other enclosure after
delivery.
Fig. 1: Examples of the VACON®100 IP00 drive module
PREFACE VACON · 3
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

VACON · 4
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

TABLE OF CONTENTS
Preface
Document details 3
About this manual 3
About the product 3
1 Approvals 8
2 Safety 10
2.1 The safety symbols used in the manual 10
2.2 Warning 10
2.3 Caution 11
2.4 Grounding and earth fault protection 12
2.5 Using an RCD or an RCM device 13
3 Receiving the delivery 14
3.1 Package label 14
3.2 Type designation code 15
3.3 The contents of the delivery 15
3.4 Removing the packaging and lifting the AC drive 16
3.4.1 Weight of the AC drive 16
3.4.2 Lifting the IP00 drive module 16
3.5 "Product modified" label 19
3.6 Disposal 20
4 Mounting dimensions 21
4.1 Dimensions of MR8, IP00 21
4.2 Dimensions of MR9, IP00 22
4.3 Dimensions of MR10 and MR12, IP00 23
4.4 Dimensions for flange mounting of MR8 25
4.5 Dimensions for flange mounting of MR9 26
4.6 Dimensions for flange mounting of MR10 27
4.7 Dimensions of options for MR10 and MR12 28
5 Installation into cabinet 30
5.1 General information 30
5.1.1 General information about the installation, MR8-MR9 30
5.1.2 General information about the installation, MR10 31
5.1.3 General information about the installation, MR12 34
5.2 Mechanical installation 36
5.2.1 Installing the IP00 drive module into the cabinet 37
5.2.2 Flange mounting of the IP00 drive module 39
5.2.3 Installing a detached control unit 41
5.2.4 Cooling and free space around the AC drive 42
6 Power cabling 45
6.1 Cable dimensioning and selection 45
6.1.1 Cable and fuse sizes 45
6.1.2 Cable and fuse sizes, North America 52
6.2 Brake resistor cables 57
TABLE OF CONTENTS VACON · 5
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

6.3 Preparing for the cable installation 59
6.4 Cable installation 60
6.4.1 Enclosure sizes MR8 and MR9 60
6.4.2 Enclosure sizes MR10 and MR12 64
7 Control unit 73
7.1 Control unit components 73
7.2 Control unit cabling 75
7.2.1 Selection of the control cables 75
7.2.2 Control terminals and DIP switches 75
7.3 Fieldbus connection 79
7.3.1 Using fieldbus through an Ethernet cable 80
7.3.2 Using fieldbus through an RS485 cable 81
7.4 Installation of option boards 84
7.4.1 The installation procedure 85
7.5 Installation of a battery for the Real Time Clock (RTC) 86
7.6 Galvanic isolation barriers 86
8 Commissioning and additional instructions 88
8.1 Commissioning safety 88
8.2 Operation of the motor 89
8.2.1 Checks before starting the motor 89
8.3 Measuring the cable and motor insulation 89
8.4 Installation in a corner-grounded network 89
8.5 Installation in an IT system 90
8.5.1 The EMC jumper in MR8 90
8.5.2 The EMC jumper in MR9 91
8.5.3 The EMC jumper in MR10 and MR12 92
8.6 Maintenance 95
8.6.1 Maintenance intervals 95
8.6.2 Replacing the fans of the AC drive 96
8.6.3 Downloading the software 100
9 Technical data, VACON®100 INDUSTRIAL 103
9.1 AC drive power ratings 103
9.1.1 Mains voltage 208-240 V 103
9.1.2 Mains voltage 380-500 V 104
9.1.3 Mains voltage 525-690 V 105
9.1.4 Overload capability 105
9.1.5 Brake resistor ratings 106
9.2 VACON®100 INDUSTRIAL - technical data 110
10 Technical data, VACON®100 FLOW 115
10.1 AC drive power ratings 115
10.1.1 Mains voltage 208-240 V 115
10.1.2 Mains voltage 380-500 V 116
10.1.3 Mains voltage 525-690 V 117
10.1.4 Overload capability 117
10.2 VACON®100 FLOW - technical data 119
VACON · 6 TABLE OF CONTENTS
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

11 Technical data on control connections 124
11.1 Technical data on control connections 124
TABLE OF CONTENTS VACON · 7
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

1 APPROVALS
Here are the approvals that have been granted to this VACON®product.
1.EC Declaration of conformity
•Find the EC Declaration of Conformity on the next page.
2.UL approval *
•cULus approval file number E171278.
3.KC approval
•Registration number MSIP-REM-V93-VC100.
* The UL approval is valid for input voltage up to 600 V.
VACON · 8 APPROVALS
1 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

Antti Vuola
Head of Standard Drives
Timo Kasi
VP, Design Center Finland and Italy
Danfoss A/S
DK-6430 Nordborg
Denmark
CVR nr.: 20 16 57 15
Telephone: [phone]
Fax: [phone]
15-04-2016 15-04-2016
Date Issued by Date Approved by
Signature
Name
Title
Signature
Name
Title
Danfoss only vouches for the correctness of the English version of this declaration. In the event of the declaration being translated
into any other language, the translator concerned shall be liable for the correctness of the translation.
EU DECLARATION OF CONFORMITY
Danfoss A/S
Vacon Ltd
declares under our sole responsibility that the
Product(s) VACON® 100 AC drive
Type(s) Wall-Mounted Drives:
VACON® 0100 3L 0003 2...0310 2
VACON® 0100 3L 0003 4...0310 4
VACON® 0100 3L 0003 5...0310 5
VACON® 0100 3L 0004 6...0208 6
VACON® 0100 3L 0007 7...0208 7
Covered by this declaration is in conformity with the following directive(s), standard(s) or other normative document(s),
provided that the product is used in accordance with our instructions.
Safety: EN 61800-5-1: 2007
EN 60204-1: 2006+A1:2009 (as relevant)
EMC: EN 61800-3: 2004 + A1: 2012
and conforms to the relevant safety provisions of Low Voltage Directive 2006/95/EC (until April 19th, 2016), 2014/35/EU
(from April 20th, 2016) and EMC Directive 2004/108/EC (until April 19th, 2016), 2014/30/EU (from April 20th, 2016).
The year the CE marking was affixed: 2009
IP00 Drives:
VACON® 0100 3L 0140 2...0310 2
VACON® 0100 3L 0140 5...1180 5
VACON® 0100 3L 0080 6...0820 6
VACON® 0100 3L 0080 7...0820 7
Enclosed Drives:
VACON® 0100 3L 0140 5...1180 5
VACON® 0100 3L 0080 7...0820 7
APPROVALS VACON · 9
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 1

2 SAFETY
2.1 THE SAFETY SYMBOLS USED IN THE MANUAL
This manual contains warnings and cautions, which are identified with safety symbols. The
warnings and cautions give important information on how to prevent injury and damage to
the equipment or your system.
Read the warnings and cautions carefully and obey their instructions.
Table 1: The safety symbols
The safety symbol The safety word Description
WARNING!
If you do not obey the
instructions, injury or
death is possible.
CAUTION!
If you do not obey the
instructions, damage to
the equipment is possible.
HOT SURFACE!
If you do not obey the
instructions, burns are
possible.
2.2 WARNING
WARNING!
Do not touch the components of the power unit when the drive is connected to
mains. The components are live when the drive is connected to mains. A contact
with this voltage is very dangerous.
WARNING!
Do not touch the motor cable terminals U, V, W, the brake resistor terminals or the
DC terminals when the drive is connected to mains. These terminals are live when
the drive is connected to mains, also when the motor does not operate.
WARNING!
Do not touch the control terminals. They can have a dangerous voltage also when
the drive is disconnected from mains.
VACON · 10 SAFETY
2 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

WARNING!
Before you do electrical work on the drive, disconnect the drive from the mains and
make sure that the motor has stopped. Lock out and tag out the power source to
the drive. Make sure that no external source generates unintended voltage during
work. Note that also the load side of the drive can generate voltage.
Wait 5 minutes before you open the cabinet door or the cover of the AC drive. Use a
measuring device to make sure that there is no voltage. The terminal connections
and the components of the drive can be live 5 minutes after it is disconnected from
the mains and the motor has stopped.
WARNING!
Before you connect the drive to mains, make sure that the front cover and the cable
cover of the drive are closed. The connections of the AC drive are live when the
drive is connected to mains.
WARNING!
Disconnect the motor from the drive if an accidental start can be dangerous. When
there is a power-up, a power break or a fault reset, the motor starts immediately if
the start signal is active, unless the pulse control for Start/Stop logic is selected. If
the parameters, the applications or the software change, the I/O functions
(including the start inputs) can change.
WARNING!
Wear protective gloves when you do mounting, cabling or maintenance operations.
There can be sharp edges in the AC drive that can cause cuts.
2.3 CAUTION
CAUTION!
Do not move the AC drive. Use a fixed installation to prevent damage to the drive.
CAUTION!
Do not make measurements when the AC drive is connected to mains. It can cause
damage to the drive.
CAUTION!
Make sure that there is reinforced protective ground connection. It is mandatory,
because the touch current of the AC drives is more than 3.5 mA AC (refer to EN
61800-5-1). See chapter 2.4 Grounding and earth fault protection.
CAUTION!
Do not use spare parts that are not from the manufacturer. Using other spare parts
can cause damage to the drive.
CAUTION!
Do not touch the components on the circuit boards. Static voltage can cause
damage to these components.
SAFETY VACON · 11
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 2

CAUTION!
Make sure that the EMC level of the AC drive is correct for your mains. See chapter
8.5 Installation in an IT system. An incorrect EMC level can cause damage to the
drive.
If you use Corner-grounding, change the EMC level to C4, see chapter 8.5
Installation in an IT system.
For information on permitted drive types for Corner-grounding, see chapter 8.4
Installation in a corner-grounded network.
CAUTION!
Prevent radio interference. The AC drive can cause radio interference in a domestic
environment.
NOTE!
If you activate the autoreset function, the motor starts automatically after an
automatic fault reset. See the Application Manual.
NOTE!
If you use the AC drive as a part of a machine, the machine manufacturer must
supply a mains disconnection device (refer to EN 60204-1).
2.4 GROUNDING AND EARTH FAULT PROTECTION
CAUTION!
The AC drive must always be grounded with a grounding conductor that is
connected to the grounding terminal that is identified with the symbol . Not using
a grounding conductor can cause damage to the drive.
The touch current of the drive is more than 3.5 mA AC. The standard EN 61800-5-1 tells that
1 or more of these conditions for the protective circuit must be true.
The connection must be fixed.
a)The protective grounding conductor must have a cross-sectional area of minimum 10
mm2Cu or 16 mm2Al. OR
b)There must be an automatic disconnection of the mains, if the protective grounding
conductor breaks. See chapter 6 Power cabling. OR
c)There must be a terminal for a second protective grounding conductor in the same
cross-sectional area as the first protective grounding conductor.
VACON · 12 SAFETY
2 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

Table 2: Protective grounding conductor cross-section
Cross-sectional area of the phase conductors (S)
[mm2]
The minimum cross-sectional area of the protective
grounding conductor in question [mm2]
S ≤ 16 S
16 < S ≤ 35 16
35 < S S/2
The values of the table are valid only if the protective grounding conductor is made of the
same metal as the phase conductors. If this is not so, the cross-sectional area of the
protective grounding conductor must be determined in a manner that produces a
conductance equivalent to that which results from the application of this table.
The cross-sectional area of each protective grounding conductor that is not a part of the
mains cable or the cable enclosure, must be a minimum of:
•2.5 mm2if there is mechanical protection, and
•4 mm2if there is not mechanical protection. If you have cord-connected equipment,
make sure that the protective grounding conductor in the cord is the last conductor to be
interrupted, if the strain-relief mechanism breaks.
Obey the local regulations on the minimum size of the protective grounding conductor.
NOTE!
Because there are high capacitive currents in the AC drive, it is possible that the
fault current protective switches do not operate correctly.
CAUTION!
Do not do voltage withstand tests on the AC drive. The manufacturer has already
done the tests. Doing voltage withstand tests can cause damage to the drive.
2.5 USING AN RCD OR AN RCM DEVICE
The drive can cause a current in the protective grounding conductor. You can use a residual
current-operated protective (RCD) device, or a residual current-operated monitoring (RCM)
device to give protection against a direct or an indirect contact. Use a type B RCD or RCM
device on the mains side of the drive.
NOTE! You can download the English and French product manuals with applicable safety, warning and caution
information from http://drives.danfoss.com/knowledge-center/technical-documentation/.
REMARQUE Vous pouvez télécharger les versions anglaise et française des manuels produit contenant l'en-
semble des informations de sécurité, avertissements et mises en garde applicables sur le site http://
drives.danfoss.com/knowledge-center/technical-documentation/.
SAFETY VACON · 13
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 2

3 RECEIVING THE DELIVERY
Before a VACON®AC drive is sent to the customer, the manufacturer makes many tests on
the drive to ensure its quality. When you receive the delivery, examine the packaging
carefully. After you remove the packaging, examine the drive for transport damages.
If the drive was damaged during the shipping, speak to the cargo insurance company or the
carrier.
To make sure that the contents of the delivery is correct and complete, compare the type
designation of the product to the type designation code. See Chapter 3.2 Type designation
code.
3.1 PACKAGE LABEL
To make sure that the delivery is correct, compare your order data to the data on the
package label. If the delivery does not agree with your order, speak to the vendor
immediately.
A B
H
G
F
E
D
C
I
Danfoss Industries Pte. Ltd.
MSIP-REM-V93-VC100
VAF
1000418030
V00001331708
70-AB3L07305W12B030BM26-00074393
Danfoss A/S, 6430 Nordborg, Denmark
3~AC,0-Uin, 0-320Hz
Uin:3~AC,380-500V, 50/60Hz
730A 40°C / 650A 50°C
724A 40°C / 642A 50°C
400kW:400V / 600HP:480V
IP00/Open Type
Made in Finland
POWER:
OUTPUT:
INPUT:
VACON0100-3L-0730-5+IP00
170120
16695624
FW0072V025
Marks:
Cust. Ord. No:
Application:
Firmware:
B.ID:
V00001331708
S/N:
70-AB3L07305W12B030BM26-00074393
Code:
Type:
AC DRIVE
Fig. 2: The package label of VACON®AC drives
A. The batch ID
B. The VACON®order number
C. The type designation code
D. The serial number
E. The mains voltage
F. The nominal output current
G. The IP class
H. The application code
I. The order number of the customer
VACON · 14 RECEIVING THE DELIVERY
3 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

3.2 TYPE DESIGNATION CODE
The type designation code is made of standard codes and option codes. Each part of the type
designation code agrees to the data in your order. The code can have this format, for
example:
VACON0100-3L-0385-5-FLOW+IP00
Table 3: The description of the parts in the type designation code
Code Description
VACON0100 The product family: VACON0100 = the VACON®100 product family
3L Input/Function: 3L = A 3-phase input
0385 The drive rating in amperes. For example, 0385 = 385 A
5 The mains voltage:
2 = 208-240 V
5 = 380-500 V
7 = 525-690 V
FLOW The product:
(empty) = The VACON®100 INDUSTRIAL AC drive
FLOW = The VACON®100 FLOW AC drive
+IP00 The enclosure class of the AC drive is IP00.
3.3 THE CONTENTS OF THE DELIVERY
The contents of the delivery, MR8-MR9
•The IP00 drive module with an integrated control unit
•An accessories bag
•Installation Manual, Application Manual and manuals for the options that you ordered
The contents of the delivery, MR10
•The IP00 drive module with an integrated control unit
•An accessories bag
•The options module, if you ordered it with options
•Installation Manual, Application Manual and manuals for the options that you ordered
The contents of the delivery, MR12
•The IP00 drive module: 2 power units, 1 of them with an integrated control unit
•An accessories bag
•The options module, if you ordered it with options
•A DC link cable
•A set of optical fibre cables
•Installation Manual, Application Manual and manuals for the options that you ordered
RECEIVING THE DELIVERY VACON · 15
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 3

3.4 REMOVING THE PACKAGING AND LIFTING THE AC DRIVE
3.4.1 WEIGHT OF THE AC DRIVE
The weights of AC drives of different enclosure sizes are very different. It can be necessary
for you to use a lifting device to move the drive from its package.
Table 4: The weight of the AC drive, MR8-MR12
Enclosure size or item Weight [kg] Weight [lb]
MR8 IP00 drive module 62 137
MR9 IP00 drive module 97 214
MR10 IP00 drive module 221 487
MR10 IP00 drive module and the options module with the brake
chopper 252 556
MR10 IP00 drive module and the options module with the brake
chopper and the common mode filter 258 569
MR10 IP00 drive module and the options module with the brake
chopper, the common mode filter, and the du/dt filter 289 637
MR10 IP00 drive module and the options module with AC fuses and
fuse switch (+CIFD) 332 732
MR12 IP00 drive module 442 974
MR12 IP00 drive module and the options module with the brake
chopper 504 1111
MR12 IP00 drive module and the options module with the brake
chopper and the common mode filter 516 1138
MR12 IP00 drive module and the options module with the brake
chopper, the common mode filter, and the du/dt filter 578 1274
MR12 IP00 drive module and the options module with AC fuses and
fuse switch (+CIFD) 570 1257
3.4.2 LIFTING THE IP00 DRIVE MODULE
The AC drive is delivered horizontally on a wooden pallet. Open the package only when you
install the drive. Do not keep the drive in storage in the vertical position.
LIFTING THE IP00 DRIVE MODULE, MR8 AND MR9
1 Remove the drive from the pallet where it was
bolted to.
2 Use a lifting device that is sufficiently strong for the
weight of the drive.
3 Put the lifting hooks symmetrically in a minimum of
2 holes.
VACON · 16 RECEIVING THE DELIVERY
3 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

4 The maximum lifting angle is 45 degrees.
≤45º≤45º
RECEIVING THE DELIVERY VACON · 17
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 3

LIFTING THE IP00 DRIVE MODULE, MR10 OR MR12 WITHOUT THE OPTIONS MODULE
1 Make sure that the support is attached to the
bottom of the drive. It gives the terminals
protection when you lift the drive or put it vertically
on the floor.
A
A
A. The support / fixing bracket
2 Lift the drive with a lifting device. Put the lifting
hooks in the holes on the top of the cabinet. The
maximum lifting angle is 60 degrees.
3 After the lifting, you can remove the support if
necessary. You can also use it as a fixing bracket.
LIFTING THE IP00 DRIVE MODULE, MR10 OR MR12 WITH AN OPTIONS MODULE
1 Remove the drive from the package.
2 Use a lifting device that is sufficiently strong for the
weight of the drive.
3 Put the lifting hooks in the holes on the top of the
cabinet.
VACON · 18 RECEIVING THE DELIVERY
3 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/

4 Lift the drive into a vertical position.
5 The maximum lifting angle is 60 degrees.
≤60º
3.5 "PRODUCT MODIFIED" LABEL
In the accessories bag, there is also a "product modified" label. The function of the label is to
tell the service personnel about the changes that are made in the AC drive. Attach the label
on the side of the AC drive to know where to find it. If you make changes in the AC drive, write
the change on the label.
Product modified
Date:
Date:
Date:
RECEIVING THE DELIVERY VACON · 19
LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/ 3

3.6 DISPOSAL
When the drive is at the end of its operation life, do not discard it as a part of municipal
waste. You can recycle the primary components of the drive. You must disassemble
some components before you can remove the different materials. Recycle the electrical
and electronic components as waste.
To make sure that the waste is recycled correctly, send the waste to a recycling centre.
You can also send the waste back to the manufacturer.
Obey the local and other applicable regulations.
VACON · 20 RECEIVING THE DELIVERY
3 LOCAL CONTACTS: HTTP://DRIVES.DANFOSS.COM/DANFOSS-DRIVES/LOCAL-CONTACTS/