Vaisala HMP 35A User manual

Operating instructions
Manuel d'utilisation
Bedienungsanleitung
Kaytt6ohje
HMP 35A & HMP 350
Sondes de mesure de
temperature et d'humidite
Humidity and
temperature probes
Mel"Ssonden fur Feuchte
und Temperatur Kosteus- ja lamp6tila-
mittapaat
Doc. no. HMP35A-OO217-2.1
~+}VftlSftLft
SENSORSYSTEMS

more often, depending on the conditions of use and
desired accuracy. A one-point calibration may be per-
formed for the probes during actual measurement by
adjusting the trimmer potentiometer marked "DRY" in
the probe shaft. The field calibration can be performed
against a calibrated Vaisala humidity meter. For a high-
accuracy two-point calibration use a Vaisala HMK 11
calibrator and saturated salt solutions as described in
the HMK 11 Operating Manual. The calibration is first
done for the dry end and then for the wet end by
adjusting trimmer potentiometers marked "DRY" and
"WET". The potentiometers are located under a protec-
tive plug in the probe handle, see Figure 3. (Note: the
minimum output signal of 0.002 V corresponds to a
relative humidity of 0.2 %RH.)
Replacing the H-sensor
Detach the damaged sensor and replace it with a new
one. Handle the sensor with care. Calibrate the probe,
preferably using two-point calibration, before taking it
into use.
Chemical tolerances of the H-sensor
Long-term exposure of the sensor to certain chemicals
and gases may shorten sensor life and change its
properties. The following list give suggested maximum
ambient concentrations for some typical chemicals:
1. Organic solvents 1000...10000 ppm (typ.)
Aggressive chemicals
(e.g. strong acids such
as S02' H2SO4' H2S,
HCI, C12,etc.)
2
1...10 ppm (typ.)
100...1000 ppm (typ.)
10000...100000 ppm (typ.
3,
Weak
acids
Bases4.
Detailed information on allowed concentrations is
available on request from your Vaisala representative.
2

4.
SPARE PARTS AND ACCESSORIES
HMK
11 calibrator
Radiation shield
0062
10429
2787
6685
6686
6597
HMP 35A
HUMICAP@ H-sensor
Temperature sensor Pt 100
(1/3 DIN 43760B)
Membrane filter
Sintered filter 37 ~m
Sintered filter 216 ~m
Plastic grid
HMP 35D
0062
10429
HUMICAP@ H-sensor
Temperature sensor Pt 100
(1/3 DIN 437608)
Membrane filter, chromium-plated
Sintered filter 37 ~m
Sintered filter 216 ~m
16126
6685
6686
5.
TECHNICAL SPECIFICATIONS
HMP
35A & HMP 35D
0 ...100 %RH
0.002 ...1 VDC
(equals 0.2 ...1
Measurement range
Output signal range
00
% RH)
%RH
:t
Accuracy at +20 °C
(including nonlinearity
and hysteresis)
.against factory
references
.against field references :t2 %RH (0 .,
:t3 %RH (90 90 %RH)
.100%RH)
3

Temperature dependence :to.04 %RH/oC
Typical long-term stability better than 1 % RH per year
Response time 15 s with membrane filter
(at 20 °C, 90 % response)
Settling time 1 s
Sensor HUMICAP@ H-sensor
(part no. 0062)
Pt 100 (1/3 DIN 43760B,
four-wire connection)
7...35VDC
$:4 mA
-40 ...+60 °C
IP 55 (NEMA 3S)
IP 65 (NEMA 4) *
180g
radiation shield
Temperature sensor
Supply voltage
Current consumption
Operating temperature
Protection class
Weight
Accessories
HMP 35A
Sensor protection
.standard
.optional
membrane filter
(part no. 2787)
plastic grid (part no. 6597)
sintered filter 37 ~m
(part no. 6685)
sintered filter 216 ~m
(part no. 6686)
ASS plastic
1600 mm
Housing material
Cable length
HMP 35D IEC 801-3 standard, level 2
E.M.I. protection
Sensor protection
.standard membrane filter,
chromium-plated (part no.
2787)

Sensor protection
.optional
Housing material
sintered filter 37 ~m
(part no. 6685)
sintered fi1ter 216 ~m
(part no. 6686)
chromium-plated ASS
plastic
3500 mm
Cable length
(* For details, consult your Vaisala representative.
Information and specifications in this manual subject to
change withough prior notice.
Copyright Vaisala Oy, 1991.
HUMICAP@ is a registered trademark of Vaisala.
5

HMP
35A
Fig. 3
Fig. 3
Bild 3
Kuva 3
Electrical connections
Connexions electriques
Elektrische Anschlu~e
Sahk6iset liitannat
r

Dimensions, HM P 35A & HM P 35D
Dimensions, HM P 35A & HM P 35D
Mar5e, HMP 35A & HMP 35D
Mitat, HMP 35A & HMP 35D
Fig. 1
Fig. 1
Bild 1
Kuva 1
HMP 35A
1600 mm HMP 350 3500 mm
Cable length
Longueur du cable
Lange des Kabels
Kaapelin pituus

HMP 35D
Fig. 4
Fig. 4
Bild 4
Kuva 4
Electrical connections
Connexions electriques
Elektrische AnschlOBe
Sahk6iset liitannat
-(,
,~
-SHIELC
"'-'~~~"~""~.'